cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota adm. jakarta selatan,
Dki jakarta
INDONESIA
Urania Jurnal Ilmiah Daur Bahan Bakar Nuklir
ISSN : -     EISSN : -     DOI : -
Core Subject : Science,
Jurnal Ilmiah Daur Bahan Bakar Nuklir URANIA adalah wahana informasi tentang daur bagan bakar nuklir yang berisi hasil penelitian, pengembangan dan tulisan ilmiah terkait. terbitan pertama kali pada tahun 1995 dengan frekuensi terbit sebanyak empat kali dalam setahun yakni pada bulan Januari, April, Juli dan Oktober.
Arjuna Subject : -
Articles 6 Documents
Search results for , issue "Vol 14, No 4 (2008): Oktober 2008" : 6 Documents clear
PENENTUAN KANDUNGAN Sn, Fe, Cr, Ni DAN PENGOTOR ZIRCALOY-2 SEBAGAI BAHAN KELONGSONG DAN TUTUP UJUNG ELEMEN BAKAR REAKTOR DAYA Arif Nugroho; Dian Anggraini; Rosika K; Djoko Kisworo
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (299.737 KB) | DOI: 10.17146/urania.2008.14.4.2570

Abstract

ABSTRAK PENENTUAN KANDUNGAN Sn, Fe, Cr, Ni DAN PENGOTOR ZIRCALOY-2 SEBAGAI BAHAN KELONGSONG DAN TUTUP UJUNG ELEMEN BAKAR REAKTOR DAYA. Telah dilakukan pengukuran unsur  pemadu dan pengotor dalam zircaloy-2 menggunakan alat spektrometer emisi dan X-Ray Flouresence (XRF). Tujuan penelitian ini adalah memverifikasi spesifikasi bahan zircaloy-2 (Zry-2) yang digunakan secara kualitatif dan kuantitatif. Langkah pertama yang dilakukan adalah seluruh permukaan bahan sampel standar dan sampel zircaloy-2 dihaluskan menggunakan mesin bubut, dan dibersihkan menggunakan alkohol. Sampel yang sudah bersih dan kering diukur menggunakan alat spektrometer emisi dan XRF dengan tujuh kali pengulangan. Pengukuran bahan standar dengan berbagai variasi konsentrasi unsur digunakan untuk membuat kurva kalibrasi hubungan antara konsentrasi unsur dengan intensitas. Hasil pengukuran intensitas unsur dalam sampel zircaloy-2 kemudian diplotkan ke kurva kalibrasi sehingga konsentrasi unsur dalam sampel zircaloy-2 dapat diketahui. Hasil penelitian ini diharapkan dapat dipakai sebagai metode analisis pengukuran zircaloy-2, karena alat spektrometer emisi dan XRF selektif untuk mengukur unsur-unsur logam dalam suatu bahan. Hasil pengukuran unsur pemadu dalam sampel zircaloy-2 adalah Sn 1,346%, Fe 0,2151%, Cr 0,12 % dan Ni 0,039%. Sedangkan kandungan unsur pengotor Al 42,7275 ppm, Cu 6,0335 ppm, Si 54,0706 ppm, Ti 39,9182 ppm, Co, Mn dan Mo tidak terdeteksi. Hasil analisis unsur yang diperoleh masih dalam kisaran nilai sertifikat zircaloy-2 sehingga zircaloy-2 dapat digunakan sebagai bahan kelongsong sesuai yang dipersyaratkan fabrikasi. Konsentrasi pengotor lainnya seperti B, C, Ca, Cd, Hf, H, Mg, N, Na, Nb, Pb, Ta, U, V, W dan O belum bisa ditentukan, karena keterbatasan bahan standar dan detektor yang digunakan pada alat spektrometer emisi. Kata kunci : Zircaloy-2, metode spektrometri emisi dan X-ray fluorescence (XRF)   ABSTRACT Determination of Sn, Fe, Cr, Ni and Zr-2 impurities as cladding material and end cup of fuel element for power reactor. A measurement of major and poison elements in zircaloy-2 using emission spectrometer and X-Ray Fluorescence (XRF) equipment has been conducted. The objective of this investigation is for verifying specification of zircaloy-2 material by qualitative and quantitative method. Firstly, the surface of standards and a Zr-2 sample were smoothed by lathe equipment, and cleaned by using alcohol. The clean and dry samples were measured by emission spectrometer and XRF equipment seven times. The measurement of standard elements with different concentrations was carried out to prepare calibration curves of element concentrations versus intensity. Hence, the element intensities of zircaloy-2 sample were plotted to calibration curve so that the concentration can be found. The result of measurement is expected to be used as zircaloy-2 measurement analysis method, since emission spectrometer and XRF equipment are selective for measuring metal element in the materials. The results obtained were Sn 1.346%, Fe 0.2151%, Cr 0.12 % and Ni 0.039%, whilst the impurities were  Al 42.7275 ppm, Cu 6.0335 ppm, Si 54.0706 ppm, Ti 39.9182 ppm, and Co, Mn and Mo were not detected. The result analysis showed that the specification of Zr-2 sample is still in the limit so that it can be used as a cladding material. The other impurities such as  B, C, Ca, Cd, Hf, H, Mg, N, Na, Nb, Pb, Ta, U, V, W and O could not measured because the standard materials and the detectors  are not available in place. Key words: Zircaloy-2, emission spectrometry method and X-ray fluorescence (XRF).
PENENTUAN WAKTU TANGGAP TERMAL BATANG BAHAN BAKAR SELAMA PEMADAMAN REAKTOR NUKLIR DENGAN MENGGUNAKAN MODEL ADIABATIK Suwardi .
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (435.33 KB) | DOI: 10.17146/urania.2008.14.4.2571

Abstract

ABSTRAK WAKTU TANGGAP TERMAL  BATANG  BAHAN  BAKAR SELAMA PEMADAMAN  REAKTOR NUKLIR DENGAN  MENGGUNAKAN  MODEL  ADIABATIK. Proses pemadaman reaktor nuklir yang kompleks tergantung dari parameter disain bahan bakar dan parameter dan operasi reaktor. Dalam kaitan dengan analisis RIA dan LOCA, proses pemadaman dicirikan dengan konstanta waktu tanggap termal. Pada makalah ini disajikan konsep konstanta waktu tanggap termal dengan memperhitungkan transfer panas antara batang bahan bakar dan pendingin dengan model adiabatik yang  lebih realistik daripada model temperatur permukaan konstan yang saat ini masih digunakan. Model ini diselesaikan secara eksakta ke deret Bessel. Pendekatan numerik menghasilkan rumus perhitungan sederhana sampai 4 suku. Dibandingkan perhitungan dengan menggunakan kode Transuranus yang telah diverifikasi dengan pengukuran eksperimental, waktu tanggap model termal adiabatik untuk tipikal BB PWR sedikit lebih rendah.   Kata kunci : Waktu tanggap termal, batang bahan bakar, nuklir,  adiabatic,  fungsi Bessel   ABSTRACT DETERMINATION OF THERMAL TIME CONSTANT OF FUEL PIN DURING NUCLEAR REACTOR SHUT DOWN BY USING ADIABATIC MODEL. A complex shut down process of nuclear reactor depends on different parameters of fuel design and of reactor operation. In correlation to RIA and LOCA analyses of reactor core, the shut down process is characterized by a time constant. In this paper, the concept of time constant by considering adiabatic heat transfer between fuel pin and coolant fluid is analyzed. The concept is more realistic than the model of constant surface temperature that is still used currently. The model has been mathematically solved by Bessel function. The numerical approach obtained a simple formula until 4 significant terms. Comparison between temperature constant of typical PWR fuel obtained by the adiabatic model and by Transuranus calculations that have been verified by experimental measurement shows a slightly lower. Keyword : Thermal time constant, fuel pin, nuclear reactor, adiabatic, Bessel function. 
KAJIAN KESELAMATAN KRITIKALITAS PADA RANCANGAN TANGKI V-401 UNTUK MENYIMPAN LARUTAN URANIL NITRAT (UN) DIPERKAYA U235 SAMPAI 5% Bambang G Susanto
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2008.14.4.2572

Abstract

ABSTRAK KAJIAN KESELAMATAN KRITIKALITAS PADA RANCANGAN TANGKI V-401 UNTUK MENAMPUNG LARUTAN URANIL NITRAT (UN) DIPERKAYA U235 SAMPAI 5%. Telah dilakukan kajian keselamatan kritikalitas padarancangan tangki V-401 untuk mengetahui apakah tangki penyimpan tersebut dapat digunakan untuk menampung larutan uranil nitrat diperkaya U235 sampai 5%. Dengan menggunakan program Monte Carlo Code Neutron Particle (MCNP) versi 4.C untuk tangki V-401, diperoleh harga Keff sebesar 0.98657 bila ketinggian cairan UN mencapai 120 cm. Harga Keff mencapai 1.01101 bila ketinggian cairan UN pada posisi 130 cm. Harga Keff akan semakin besar yaitu 1.15679 bila keinggian cairan UN mencapai 330 cm (batas kapasitas penuh). Desain tangki V-401 tidak aman secara geometri karena volume dan diameter tangki terlalu besar.  Namun demikian, kalau racun netron gelas raschig ring borosilikat dimasukkan (mengisi hampir 1/3 volume tangki) hasil analysis menunjukkan harga Keff = 0.030 untuk ketinggian cairan UN  330 cm. Harga Keff akan tetap konstan di sekitar harga 0.030 untuk berbagai variasi koordinat sumber netron.Tangki V-401 tetap dapat digunakan walaupun tidak aman secara geometri, jika diisi dengan racun netron dari gelas raschig ring borosilikat, untuk menurunkan harga Keff <1. Katakunci: kritikalitas, keselamatan, uranium diperkaya ABSTRACT CRITICALITY SAFETY ASSESSMENT ON THE DESIGN OF TANK V-401 TO ACCUMULATE THE URANYL NITRATE SOLUTION ENRICHED U235 UP TO 5%. The criticality safety assessment has been conducted to tank of V-401 to know wether the tank can accumulate the uranyl nitrate solution enriched U235 up to 5%. By using Monte Carlo Code Neutron Particle (MCNP) program version 4C for tank V-401, is obtained the value of Keff 0.98657 when the height of fluid of UN reach up to 120 cms. The value of Keff would be 1,01101 when the height of UN fluid at the position of 130 cms. The value of Keff will reach up to 1,15679 when the height of UN fluid has reached the position 330 cms (full capacity limit).  Tank design V-401 is not safe geometrically because volume and tank diameter were too large. However, if neutron poison of glass raschig borosilicate ring is filled to the tank (fills approximately 1/3 tank volume) the result of analysis shows the value of Keff = 0.030 at the UN fluid position 330 cms. The value of Keff would constantly be around value of 0.030 for various coordinates source of neutron. The tank V-401 still can be utilized eventhough is not safe geometrically, if the tank is filled with neutron poison of glass raschig borosilicate ring to reduce the value of Keff <1. Keywords: criticality, safety, enriched uranium
PERILAKU SERBUK UO2 HASIL PROSES ADU, AUC, IDR DAN MODIFIED ADU SELAMA PROSES PENYINTERAN MENGGUNAKAN DILATOMETER Tri Yulianto; Etty Mutiara
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2008.14.4.2568

Abstract

ABSTRAK PERILAKU SERBUK UO2 HASIL PROSES ADU, AUC, IDR DAN MODIFIED ADU SELAMA PROSES PENYINTERAN MENGGUNAKAN DILATOMETER. Telah dilakukan penelitian perilaku serbuk UO2 selama penyinteran. Pengamatan perilaku serbuk tersebut dilakukan terhadap empat macam serbuk UO2 yang diperoleh dari jalur proses yang berbeda yaitu rute ADU, AUC, IDR dan Modified ADU. Hal ini bertujuan untuk menentukan serbuk UO2 yang mempunyai mampu sinter yang baik tanpa perlakuan pengkondisian awal terhadap serbuk tersebut. Dengan demikian proses penyinteran dapat dilakukan pada temperatur yang lebih rendah dan waktu lebih singkat sehingga biaya proses peletisasi dapat ditekan. Untuk pengamatan perilaku serbuk selama penyinteran tersebut disiapkan pelet dari masing-masing serbuk yang dikompakkan pada tekanan 3ton/cm2 untuk cetakan berdiameter 10,34 mm. Sebelum dilakukan pengompakan, keempat macam serbuk UO2 tersebut dikarakterisasi untuk mendapatkan data ukuran serbuk rata-rata dan luas muka serbuk. Penelitian ini dilakukan menggunakan tungku sinter yang dilengkapi dilatometer dengan memvariasikan temperatur sinter dengan tiga variasi (1450 oC, 1600 oC dan 1750 oC) untuk penyinteran dengan waktu sinter 4 jam. Hasil pengamatan berupa kurva dilatometer, densitas geometri dan mikrograf SEM pelet sinter yang selanjutnya diolah untuk menentukan mampu sinter masing-masing serbuk. Berdasarkan olahan data hasil pengamatan dapat disimpulkan bahwa serbuk modified ADU mempunyai mampu sinter yang paling baik yang ditandai dengan laju penyusutan pelet yang tinggi selama penyinteran sehingga mampu mencapai densitas akhir dan ukuran butir sesuai persyaratan pada temperatur sinter lebih rendah dan waktu sinter yang lebih singkat. Kata kunci: serbuk UO2, mampu sinter, ukuran serbuk, luas muka,densitas, dilatometer.   ABSTRACT THE BEHAVIOR OF UO2 POWDER FROM ADU, AUC, IDR AND MODIFIED ADU PROCESSES DURING SINTERING USING DILATOMETER. Research on the behavior of UO2 powder during sintering has been performed. Observation of the powder behavior is conducted on four types of UO2 powder prepared from ADU, AUC, IDR and Modified ADU routes. The purpose is to determine UO2 powder that has good sinterability without pre-conditioning treatment on the powder. Thus the sintering process can be carried out at lower temperature and shorter time that will minimize the cost of pelletization process. To observe powder behavior during sintering, pellets from each type of powder are prepared by means of compacting at a pressure of 3 ton/cm2 for die of 10.34 mm in diameter.The investigation is performed using sintering furnace that is equipped with a dilatometer and varying sintering temperature with three variation (1450 oC, 1600 oC and 1750 oC)  for hold time of 4 hours. Before compaction, the UO2 powders are characterized to obtain the average powder size and surface area. Result of the observation are dilatometer curves, pellet density and SEM micrographs of the sintered pellets which are further processed to determine the sinterability of powder. It is concluded that Modified ADU powder has the best sinterability indicated by the activeness and high shrinkage rate during sintering that allow the powder to achieve high final density and grain size as specified at lower sintering temperature and shorter sintering time. Keyword : UO2 powder, sinterability, powder size, surface area, density, dilatometer.
ENERGY AUDIT FOR THE ELECTRICAL SYSTEM IN THE COMMERCIAL BUILDING Amiral Aziz; Rizka Elyza Sari
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2008.14.4.2573

Abstract

ABSTRACT ENERGY AUDIT  FOR  THE  ELECTRICAL  SYSTEM IN THE  COMMERCIAL BUOLDING . This papers presents some results of the energy audit that was conducted in the commercial building i.e a hotel  to recommended measures to decrease energy costs every month by identifying of energy loss. This audit focused on the electrical system. The performance of this system was examined to identify opportunities for improving energy efficiency. It is concluded that approximately 65 % of electricity use in the object study is for its central air conditioning system. Therefore, automatic energy saving adjustments towards the air conditioning system will provide a significant amount of savings. Keywords: Energy audit, electrical system ABSTRAK AUDIT  ENERGI UNTUK SISTEM  ELEKTRIKAL  PADA GEDUNG  KOMERSIAL. Tulisan ini menampilkan beberapa hasil dari audit energi yang telah dilakukan untuk gedung komersial dalam hal ini hotel untuk menurunkan biaya energi setiap bulan dengan cara mengidentifikasi kehilangan energi. Audit ini difokuskan pada system elektrikal. Kinerja system ini telah dievaluasi untuk mengidentifikasi oportunitas memperbaiki efisiensi energy. Disimpulkan bahwa sekitar 65 % dari penggunaan energi pada objek studi adalah untuk system pengkondisian udara sentral. Oleh karena itu, pengaturan penghematan energi otomatis pada system pengkondisian udara akan memberikan jumlah yang cukup siknifikan. Kata Kunci : Audit energi, sistem elektrikal
PENGARUH UNSUR Zr PADA PADUAN U-Zr DAN INTERAKSINYA DENGAN LOGAM Al TERHADAP PEMBENTUKAN FASA Masrukan .; Aslina Br.Ginting
Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol 14, No 4 (2008): Oktober 2008
Publisher : website

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2008.14.4.2569

Abstract

ABSTRAK PENGARUH  UNSUR Zr  PADA PADUAN U-Zr DAN   INTERAKSINYA  DENGAN LOGAM Al   TERHADAP PEMBENTUKAN FASA. Telah dilakukan penelitian tentang pengaruh penambahan unsur Zr pada paduan U-Zr dan interaksinya dengan logam Al  terhadap pembentukan fasa.  Mula-mula paduan U-Zr dengan komposisi Zr masing-masing 2, 6, 10, 14 dan 55 %  ditambah logam Al dengan perbandingan U-Zr dan logam Al sebagai satu dibanding setengah. Setelah dicampur dengan logam Al selanjutnya dikenai pengujian dengan menggunakan DTA pada interval temperatur dari temperatur kamar hingga 1000 oC. Penambahan logam Al dimaksudkan untuk mensimulasikan kondisi bahan bakar pada saat digunakan di reaktor. Adanya logam Al pada paduan U-Zr akan mengakibatkan terjadinya reaksi termokimia dan terbentuknya fasa-fasa, dimana fasa yang terbentuk akan mempengaruhi kinerja bahan bakar di dalam reaktor.  Penelitian ini bertujuan untuk   mengetahui reaksi termokimia antara paduan U-Zr dengan logam Al sebagai matriks.  Hasil analisis menunjukkan terjadinya pembentukan fasa dari fasa α + δ menjadi α + γ Zr  pada semua komposisi, dan pada pembentukan fasa tersebut pada 55 %Zr  membutuhkan panas yang paling besar dibandingkan pada  2, 6, 10, 14 % Zr.   Selain itu, dapat diketahui bahwa  pada U-Zr dengan kandungan  Zr masing-masing  2, 6, 10 dan 14 terbentuk fasa berturut-turut  α, γ Zr, β,  δ, UAl2,  γU dan  ZrAl2,  sedangkan pada 55 % Zr jumlah fasa yang terbentuk  lebih sedikit yakni  fasa   α, γ Zr, β,  UAl2,  dan ZrAl2. Pembentukan fasa pada  2,6,10 dan  14 %  Zr  berlangsung  pada temperatur   yang berbeda meskipun fasa yang terbentuk sama. Panas yang dibutuhkam untuk proses pembentukan fasa mengalami kenaikan  apabila  persen Zr naik,  misalnya untuk 2 % berat  Zr panas yang dibutuhkan untuk membentuk β + δ  sebesar 0,8721 cal/g akan menjadi sebesar 3,0201 cal/g apabila konsentrasi  Zr sebesar 10 % berat. Kata kunci : Paduan U-Zr, Interaksi, logam Al dan  fasa.   ABSTRACT INFLUENCE of Zr ELEMENT AT U-Zr ALLOYS AND IT   INTERACTION WITH THE  Al  METAL TO PHASE FORMING. Have been done research of  Zr element addition influence at  U-Zr alloys and its interaction with the Al metal  to phase forming.  Originally,   U-Zr alloy with the composition of 2, 6, 10, 14 and 55 % w Zr respectively  are  added  by  Al metal with the comparison of U-Zr and Al metal  as one compared to  half. After the U metal  are  mixed with Al metal,   then it  physical properties tested  by using DTA at temperature interval from room  temperature up to  1000 oC. Addition of Al metal intended  to  the simulation of fuel condition at the time of used in reactor. The Al  metal  in   U-Zr alloy  will result the thermochemical reaction  and phases forming, where the phase formed will influence the fuel performance in reactor. This research  intend  to know the thermochemical reaction between U-Zr alloy with the Al metal as matrix. Result of analysis show the phases  forming  from α + δ to α + γZr at all of composition, and at the phase forming at 55 % Zr require the biggest heat if it  compared with  2, 6, 10, 14 %  weight Zr. Others, knowable that at U-Zr alloy with  Zr concentration  of  2, 6, 10 and 14 are pahses  formed  Zr α, γ Zr, β,  δ, UAl2,  γU and  ZrAl2, while at 55 % w Zr  the  total phases  formed  slimmer,   that are α, γ Zr, β, UAl2,  and  ZrAl2. Phases forming  at  2,6,10 and 14 %  w Zr   take place at  different temperature,  although the phases  formed  are same. The heat  that  is needed to phases forming process  will  increase  if  Zr percent concentration  is increase, as example for  2 % w Zr the heat  required to form β + δ   is  0,8721 cal / g will become  3,0201 cal / g  if Zr content equal to 10 % w Zr. Keyword :  U-Zr alloy, Interaction,  Al metal  and phase.

Page 1 of 1 | Total Record : 6


Filter by Year

2008 2008


Filter By Issues
All Issue Vol 29, No 2 (2023): OKTOBER, 2023 Vol 29, No 1 (2023): APRIL, 2023 Vol 28, No 3 (2022): OKTOBER, 2022 Vol 28, No 2 (2022): JUNI, 2022 Vol 28, No 1 (2022): Februari, 2022 Vol 27, No 3 (2021): Oktober, 2021 Vol 27, No 2 (2021): Juni, 2021 Vol 27, No 1 (2021): Februari, 2021 Vol 26, No 3 (2020): Oktober, 2020 Vol 26, No 2 (2020): Juni 2020 Vol 26, No 1 (2020): Februari, 2020 Vol 25, No 3 (2019): Oktober, 2019 Vol 25, No 2 (2019): Juni, 2019 Vol 25, No 1 (2019): Februari, 2019 Vol 24, No 3 (2018): Oktober, 2018 Vol 24, No 2 (2018): Juni, 2018 Vol 24, No 1 (2018): Februari, 2018 Vol 23, No 3 (2017): Oktober 2017 Vol 23, No 2 (2017): Juni 2017 Vol 23, No 1 (2017): Februari 2017 Vol 22, No 3 (2016): Oktober 2016 Vol 22, No 2 (2016): Juni 2016 Vol 22, No 1 (2016): Februari 2016 Vol 21, No 3 (2015): Oktober 2015 Vol 21, No 2 (2015): Juni 2015 Vol 21, No 1 (2015): Februari 2015 Vol 20, No 3 (2014): Oktober 2014 Vol 20, No 2 (2014): Juni 2014 Vol 20, No 1 (2014): Februari 2014 Vol 19, No 3 (2013): Oktober 2013 Vol 19, No 2 (2013): JUNI 2013 Vol 19, No 1 (2013): Februari 2013 Vol 18, No 3 (2012): Oktober 2012 Vol 18, No 2 (2012): Juni 2012 Vol 18, No 1 (2012): Februari 2012 Vol 17, No 3 (2011): Oktober 2011 Vol 17, No 2 (2011): Juni 2011 Vol 17, No 1 (2011): Februari 2011 Vol 16, No 4 (2010): Oktober 2010 Vol 16, No 3 (2010): Juli 2010 Vol 16, No 2 (2010): April 2010 Vol 16, No 1 (2010): Januari 2010 Vol 15, No 4 (2009): Oktober 2009 Vol 15, No 2 (2009): April 2009 Vol 15, No 1 (2009): Januari 2009 Vol 14, No 4 (2008): Oktober 2008 Vol 14, No 3 (2008): Juli 2008 Vol 14, No 2 (2008): April 2008 Vol 14, No 1 (2008): Januari 2008 More Issue