Article Per Year (5 Year)
p-Index From 2021 - 2026
0
P-Index
This Author published in this journals
All Journal International Journal of Renewable Energy Development
Sözen, Adnan
Unknown Affiliation
Chemistry Energy

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search
Journal : International Journal of Renewable Energy Development

 1 
Experimental and Numerical Investigation of Nanofluid Usage in a Plate Heat Exchanger for Performance Improvement Sözen, Adnan; Khanları, Ataollah; Çiftçi, Erdem
International Journal of Renewable Energy Development Vol 8, No 1 (2019): February 2019
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.8.1.27-32

Abstract

Plate heat exchangers, a compact-type heat exchanger, are commonly used heat transfer devices because of their superior characteristics. Their thermal performances are strongly dependent to working fluid circulating inside the system. The influences of nanofluid utilization as the working fluid in a plate heat exchanger was experimentally and numerically analysed in this study. In order to show off the improvement rate in heat transfer, the experiments were performed by using deionized water and TiO2-deionized water nanofluid. The nanofluid was prepared at the rate of 1.5 % as weighted. A surface-active agent, Triton X-100, was also doped into the mixture at the rate of 0.2% of a final concentration to prevent the sedimentation and flocculation of the nanoparticles inside the solution. The experiments were performed in different temperatures as 40°C, 45°C, 50°C and varying cold fluid mass flow rates as 3,4, 5, 6 and 7 lpm.  In addition, using the experimental data, a numerical simulation was realized by ANSYS Fluent software.  The both results indicate that heat transfer rate in plate heat exchanger can be improved using nanofluid as the working fluid in place of deionized water. The maximum improvement rate in heat transfer was obtained as 11 % in experimental study. It is also seen that experimental and numerical results are in good agreement.©2019. CBIORE-IJRED. All rights reservedArticle History: Received May 18th 2018; Received in revised form October 17th 2018; Accepted January 8th 2019; Available onlineHow to Cite This Article: Sözen, A., Khanlari, A., and Çiftçi, E. (2019) Experimental and Numerical Investigation of Nanofluid Usage in a Plate Heat Exchanger for Performance Improvement. Int. Journal of Renewable Energy Development, 8(1), 27-32.https://doi.org/10.14710/ijred.8.1.27-32
Energy-Exergy Analysis of A Novel Multi-Pass Solar Air Collector With Perforated Fins Aktaş, Mustafa; Sözen, Adnan; Tuncer, Azim Doğuş; Arslan, Erhan; Koşan, Meltem; Çürük, Osman
International Journal of Renewable Energy Development Vol 8, No 1 (2019): February 2019
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.8.1.47-55

Abstract

This work presents performance analysis of a novel multi-pass solar air collector with perforated fins (MPSACF) in winter conditions, Ankara province, Turkey. The aim of this work is to experimentally test  and compare the performance of the two different design of solar collectors in the same climatic conditions.  In addition, a double-pass solar air collector without fins (DPSAC) at the same absorber area was manufactured and tested as a control group. The total absorber area of both solar collectors is 0.325 m2. Thermal effects for performance improvement of the collectors have been designated.  Average thermal efficiency values of DPSAC and MPSACF were calculated as 47.85% and 51.86%, 67.10% and 72.86%, respectively in experiments performed at 0.0069 kg/s (0.7 m/s air velocity) and 0.0087 kg/s (0.9 m/s air velocity) mass flow rates. Exergy efficiency of DPSAC and MPSACF were 2.10-17.12% and 8.74-23.97%, respectively. Coefficient of performance(COP) values were ocomputed 4.63 and 4.94, 3.18 and 3.48 respectively in experiments performed at 0.0069 kg/s and 0.0087 kg/s mass flow rates. Although the MPSACF has high efficiency values, COP values are lower due to the presence of dual fans. Because of their high thermal efficiency, both collectors can be effectively practiced for applications such as preheating, space heating and ventilation, greenhouse heating and product drying©2019. CBIORE-IJRED. All rights reservedArticle History: Received May 16th 2018; Received in revised form October 16th 2018 ; Accepted January 6th 2019; Available onlineHow to Cite This Article: Aktaş, M., Sözen, A., Tuncer, A.D., Arslan, E., Koşan, M., Çürük, O. (2019) Energy-exergy analysis of a novel multi-pass solar air collector with perforated fins. International Journal of Renewable Energy Development, 8(1), 47-55.http://dx.doi.org/10.14710/ijred.8.1.47-55 
Thermal Performance Improvement of the Heat Pipe by Employing Dolomite/Ethylene Glycol Nanofluid Aydin, Duygu Yilmaz; Gürü, Metin; Sözen, Adnan; Çiftçi, Erdem
International Journal of Renewable Energy Development Vol 9, No 1 (2020): February 2020
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.9.1.23-27

Abstract

In heat transfer applications, heat pipes are widely- preferred because of some characteristics such as low cost, being able to be produced in any size and low maintenance cost make them superior. Moreover, the working fluid to be employed substantially affects the heat transfer characteristics of a heat pipe. In this paper, effects of nanoparticle addition into the ethylene glycol on heat pipe’s thermal performance were analysed experimentally. Every test was done using two variant working fluids, ethylene glycol and dolomite nanoparticles-doped ethylene glycol, respectively. Dolomite nanoparticles (2% by weight) and Sodium Dodecyl Benzene Sulfonate (0.5% by weight) were doped into the ethylene glycol while preparing the dolomite/ethylene glycol nanofluid. After filling in the heat pipe, experiments were realized under changing working conditions. Using experimental data, efficiency and thermal resistance of the heat pipe were examined. Viscosity of the each working fluid was determined. The contact angle –wettability measurements were also performed to specify the effects of surface active agent addition. The obtained findings revealed that nanoparticle inclusion inside the base fluid, i.e. ethylene glycol, improved the thermal performance (efficiency) and decreased the heat pipe’s thermal resistance substantially. ©2020. CBIORE-IJRED. All rights reserved
Co-Authors Aktaş, Mustafa Arslan, Erhan Aydin, Duygu Yilmaz Çürük, Osman Çiftçi, Erdem Gürü, Metin Khanları, Ataollah Koşan, Meltem Tuncer, Azim Doğuş