Garuda - Garba Rujukan Digital

Ashar Saputra

Department of Civil and Environmental Engineering, Universitas Gadjah Mada, Yogyakarta

Author-ID : 3516966

Civil Engineering, Building, Construction & Architecture Environmental Science

Published : 2 Documents Claim Missing Document

Claim Missing Document

Articles

Title

1

An Analysis of Energy Consumption in the Campus Building’s Operation (Case Study: The Building of Faculty of Engineering and Department of Civil and Environmental Engineering, Universitas Gadjah Mada) Syarifudin Syarifudin; Ashar Saputra; Suprapto Siswosukarto
Journal of the Civil Engineering Forum Vol. 4 No. 1 (January 2018)
Publisher : Department of Civil and Environmental Engineering, Faculty of Engineering, UGM

Energy Consumption Intensity (IKE) is an indicator that is used to determine the amount of energy used per area by an air-conditioned building within a month or a year as a reference to determine how much energy conservation can be done in the building. To determine the energy consumption of buildings and to determine the savings opportunities, there should be an effort to review the energy consumption through energy audits. In this research, energy consumption analysis was conducted at the Main Office building of the Faculty of Engineering (KPFT) and Department of Civil Engineering and Environmental (CEED) of UniversitasGadjah Mada Yogyakarta. The analysis was conducted on the main variables of energy efficiency, namely: measurement of temperature and relative humidity, calculation of Overall Thermal Transfer Value (OTTV) and Roof Thermal Transfer Value (RTTV), calculation of Energy Consumption Intensity (IKE) in air-conditioned and non-air-conditioned rooms as well as an analysis of opportunities to increase the efficiency of energy consumption in the buildings.The results showed that the temperature and the relative humidity of the KPFT building = 28.4℃ and 62%, while CEED Building = 28.4℃ dan 65%. Calculation of average OTTV of the KPFT building = 17.61 W/m2 and CEED building = 43.05 W/m2. Average IKE of the KPFT building in 2015 was 3.25 kWh/m2/month and in 2016 was 3.45 kWh/m2/month, while the average IKE of CEED building in 2015 was 1.5 kWh/m2/month and in 2016 was 0.79 kWh/m2/month. Based on the calculation of IKE in both buildings, they are still considered in the category of efficient. However, based on the measurement of temperature and relative humidity, it shows that in both buildings air conditioning is still necessary to achieve the level of thermal comfort, therefore an increase of efficiency in the load is needed to avoid wastage.

Mix Design of Self Compacting Concrete Based on Ultra High Compressive Strength Flow Mortar Mix Soca Anggoro Wulan; Iman Satyarno; Ashar Saputra
Journal of the Civil Engineering Forum Vol. 4 No. 1 (January 2018)
Publisher : Department of Civil and Environmental Engineering, Faculty of Engineering, UGM

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/jcef.29797

Mix design of Self Compacting Concrete or SCC is not straight forward because many parameters control its rheological properties. The case becomes more complicated if high compressive strength is also to be achieved. Therefore simpler approach is used, that is by firstly determining the flow mortar mix which is easier to be designed even with the requirement of ultra-high compressive strength. The mix design of SCC is then determined by simply adding the coarse aggregate with a certain amount of that mortar mix. In this research the ultra-high compressive strength flow mortar was made of Type I cement, 15% of cement weight silica fume, weight ratio of cement and curve No IV sand was 1: 0.35. The water-cementious ratio was 0.22 and the amount of plasticizer was 1.3%, 1.4%, 1.5% and 1.6% of the cement weight. For the SCC, the used coefficient was taken to be 1.4, 1.6, and 1.8 of the volume of that aggregate void for mortars, the aggregate value was at the volume of the remaining count of mortar and its size was 4.8 mm - 9.6 mm. Test results show that the mortar flow ability was 170 mm, 180 mm, 220 mm and 250 mm, where the achieved compressive strength was 83.1 MPa, 96.8 MPa, 111.4 MPa, and 135.5 MPa respectively. Mortar mix with 1.6% super plasticizer was then used for making the SCC and the results show that the concrete flow were 460 mm, 580 mm and 660 mm and the compressive strength were 88.2 MPa, 100.0 MPa, and 97.9 MPa. It can be concluded that using this simpler approach the SCC can have 580 mm flow and 100 MPa compressive strength

Title Search

Found 2 Documents Search Journal : journal of the civil engineering forum

Abstract

Abstract

Title

Found 2 Documents
Search
Journal : journal of the civil engineering forum