Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Bulletin of Electrical Engineering and Informatics

EEI
Website

Published by Universitas Ahmad Dahlan

ISSN : - EISSN : - DOI : -

Core Subject : Engineering,

Electrical & Electronics Engineering

Bulletin of Electrical Engineering and Informatics (Buletin Teknik Elektro dan Informatika) ISSN: 2089-3191, e-ISSN: 2302-9285 is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world. The journal publishes original papers in the field of electrical, computer and informatics engineering.

Arjuna Subject : -

Articles 12 Documents

1 2

Search results for , issue "Vol 6, No 1: March 2017" : 12 Documents clear

Performance of OFDM System under Different Fading Channels and Channel Coding Pratima Manhas; M. K. Soni
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Orthogonal frequency division multiplexing (OFDM) is a type of multicarrier modulation (MCM) technique in which larger bandwidth is divided into parallel narrow bands each of which is modulated by different subcarriers. All the subcarriers are orthogonal to each other and hence it reduces the interference among various subcarriers. OFDM technique is an efficient modulation technique used in certain wired and wireless application.In a wireless communication channel, the transmitted signal can travel from transmitter to receiver over multiple reflective paths. This results to multipath fading which causes fluctuations in amplitude, phase and angle of arrival of the received signal. For example, the signal which is transmitted from BTS (base transceiver station) may suffer multiple reflections from the buildings nearby, before reaching the mobile station. Such multipath fading channels are classified into slow fading/fast fading and frequency-selective/flat fading channels. This paper discusses the performance of OFDM system using various fading channels and channel coding. The parameter which is known as Bit error rate (BER) is calculated under different fading channels (AWGN, Rayleigh and Rician) for different digital modulation (BPSK, QPSK and QAM) and Channel coding (linear/Cyclic coding). Matlab Simulink tool is used to calculate the BER parameter.

A Survey on Wireless Network Simulators Amanjot Singh Toor; A. K. Jain
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

The Network simulator helps the developer to create and simulate new models on an arbitrary network by specifying both the behavior of the network nodes and the communication channels. It provides a virtual environment for an assortment of desirable features such as modeling a network based on a specific criteria and analyzing its performance under different scenarios. This saves cost and time required for testing the functionality and the execution of network. This paper has surveyed various Wireless Network Simulators and compared them.

On-chip Generation of Functional Tests with Reduced Delay and Power Hemanth Kumar Motamarri; B. Leela Kumari
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

This paper describes different methods on-chip test generation method for functional tests. The hardware was based on application of primary input sequences in order to allow the circuit to produce reachable states. Random primary input sequences were modeled to avoid repeated synchronization and thus yields varied sets of reachable states by implementing a decoder in between circuit and LFSR. The on-chip generation of functional tests require simple hardware and achieved high transition fault coverage for testable circuits. Further, power and delay can be reduced by using Bit Swapping LFSR (BS-LFSR). This technique yields less number of transitions for all pattern generation. Bit-swapping (BS) technique is less complex and more reliable to hardware miscommunications.

Routing in Networks using Genetic Algorithm Meenakshi Moza; Suresh Kumar
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

With the increase in traffic, internet service providers are trying their best to provide maximum utilization of resources available. The current traffic load has to be taken into account for computation of paths in routing protocols. Network applications; require the shortest paths to be used for communication purposes. Addressing the selection of path, from a known source to destination is the basic aim of this paper. This paper proposes a method of calculating the shortest path for a network using a combination of Open shortest path first and Genetic Algorithm (OSGA). Genetic Algorithm is used in this paper for optimization of routing. It helps in enhancing the performance of the routers.

Energy Aware Heuristic approach for Cluster Head Selection in Wireless Sensor Networks A. Tamizharasi M. E.; J. Jasmine Selvathai M. E.; A. Kavi Priya; Maarlin R.; Harinetha M.
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Wireless sensor networks idea is envisioned and defined as self-deployed, error prone, long living inexpensive communication devices that are densely deployed to collect data from physical space. Sensor nodes communicate with each other to detect events depending on the application, to collect and process data, and to transmit the sensed information to the base station by hopping the data from node to node. Major challenge in wireless network is energy consumption, since the sensor devices are deployed on unattended wide areas and replacing their batteries is not very feasible. Therefore, designing energy-aware algorithms becomes a major challenge for extending the lifetime of sensors. The lifetime of the network can be maximized by selecting the most optimal cluster head. In this paper, a heuristic decision making approach is proposed for producing energy-aware clusters with optimal selection of cluster head. This helps to improve the efficiency and accuracy and overcome the drawbacks like getting trapped at a local extreme in the optimization process.

Segmentation Comparing Eggs Watermarking Image and Original Image Anton Yudhana; Sunardi Sunardi; Shoffan Saifullah
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

The research used watermarking techniques to obtain the image originality. The aims of the research were to identify small area in eggs properly and compared preprocessing, the methods, and the results of image processing. The study has been improved from the previous papers by combined all methods and analysis was obtained.This study was conducted by using centroid and the bounding box for determining the object and the small area of chicken eggs. The segmentation method was used to compare the original image and the watermarked image. Image processing using image data that are subject watermark to maintain the authenticity of the images used in the study will the impact in delivering the desired results. In the identification of chicken eggs using watermark image using several methods are expected to provide results as desired. Segmentation also deployed to process the Image and counted the objects. The results showed that the process of segmentation and objects counting determined that the original image and watermarked image had the same value and recognized eggs. Identification had determined percentage of 100% for all the samples.

Z Source Inverter Topologies-A Survey V. Saravanan; M. Aravindan; V. Balaji; M. Arumugam
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Need for alternative energy sources to satisfy the rising demand in energy consumption elicited the research in the area of power converters/inverters. An increasing interest of using Z source inverter/converter in power generation involving renewable energy sources like wind and solar energy for both off grid and grid tied schemes were originated from 2003. This paper surveys the literature of Z source inverters/converter topologies that were developed over the years.

Design of a Low Cost Remotly Operated Vehicle with 3 Dof Navigation Romi Wiryadinata; Annisa Sucianti Nurliany; Imamul Muttakin; Teguh Firmansyah
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v6i1.596

One type of underwater robot is the ROV (Remotely Operated Vehicle) whose movements are controlled directly by humans from the water surface. In this paper, ROV prototype has been designed and tested with three DoF (Degrees of Freedom) and controlled by a joystick which is connected with UTP (Unshielded Twisted Pair) cables as data transmission between joystick with a microcontroller embedded in the robot. This prototype has 3 thrusters with 3 degrees of freedom, 1 rotational motion (heave) and 2 translational motion (yaw and surge), with direction of movement up, down, forward, backward, turn right, and turn left. Speed mode setting when forward movement on PWM (Pulse Width Modulation) 75% = 0,037 m/s, 90% = 0.053 m/s and 100% = 0,071 m/s, while the reverse speed by 75% = 0,034 m/s, 90% = 0.045 m/s and 100% = 0.059 m/s, when the ROV moves up is 0,042 m/s, down 0.032 m/s, turn right 9 o/s and turn left 15 o/s set with fixed PWM value, is 100%.

Comparison of PID Controller with Model Predictive Controller for Milk Pasteurization Process Tesfaye Alamirew; V. Balaji; Nigus Gabbeye
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Proportional–Integral–Derivative (PID) controllers are used in many of the Industries for various process control applications. PID controller yields a long settling time and overshoot which is not good for the process control applications. PID is not suitable for many of the complex process control applications. This research paper is about developing a better type of controller, known as MPC (Model Predictive Control). The aim of the paper is to design MPC and PID for a pasteurization process. In this manuscript comparison of PID controller with MPC is made and the responses are presented. MPC is an advanced control strategy that uses the internal dynamic model of the process and a history of past control moves and a combination of many different technologies to predict the future plant output. The dynamics of the pasteurization process was estimated by using system identification from the experimental data. The quality of different model structures was checked using best fit with data validation, residual and stability analysis. Auto-regressive with exogenous input (ARX322) model was chosen as a model structure of the pasteurization process and fits about 80.37% with datavalidation. MPC and PID control strategies were designed using ARX322 model structure. The controller performance was compared based on settling time, percent of overshoot and stability analysis and the results are presented.

Circuits for Optical Based Line of Sight Voice Communication Devasis Haldar; Shagun Panwar; Vipul Kumar; Ayush Goswami; Sakshi Dhawan
Bulletin of Electrical Engineering and Informatics Vol 6, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

We present here line of sight communication between a person and his neighbour with the help of optical signal produced by a laser torch which act as a carrier. It is therefore a wireless communication and the transmission can go up to 500 meters. We used photodiode to receive the signal at the receiver. The transmitter circuit comprises condenser microphone transistor amplifier BC547 followed by an op-amp stage built around µA741. When we give a voice signal from the mike, it converts the voice signal into the electrical signal. This electrical signal is fed to IC741 (op-amp) for amplification. The gain of the op-amp can be controlled with the help of 1-mega-ohm potentiometer. The AF output from IC is coupled to the base of a class B amplifier which, in turn, modulates the signal. The transmitter uses 5V power supply. However, the 3-volt laser torch (after removal of its battery) can be directly connected to the circuit-with the body of the torch connected to the class B. The photodiode converts the optical signal into electrical signal and again this signal is amplified using IC741 and a combination of class B push pull amplifiers. The receiver circuit uses an NPN photodiode as the light sensor that is followed by a two-stage transistor preamplifier and IC741 based audio Power amplifier. The receiver does not need any complicated alignment. Just keep the photodiode oriented towards the remote transmitter’s laser point and adjust the volume control for a clear sound. The sensor must not directly face the sun.

Page 1 of 2 | Total Record : 12

1 2

Filter by Year

2017 2017

Filter By Issues

All Issue Vol 14, No 6: December 2025 Vol 14, No 5: October 2025 Vol 14, No 4: August 2025 Vol 14, No 3: June 2025 Vol 14, No 2: April 2025 Vol 14, No 1: February 2025 Vol 13, No 6: December 2024 Vol 13, No 5: October 2024 Vol 13, No 4: August 2024 Vol 13, No 3: June 2024 Vol 13, No 2: April 2024 Vol 13, No 1: February 2024 Vol 12, No 6: December 2023 Vol 12, No 5: October 2023 Vol 12, No 4: August 2023 Vol 12, No 3: June 2023 Vol 12, No 2: April 2023 Vol 12, No 1: February 2023 Vol 11, No 6: December 2022 Vol 11, No 5: October 2022 Vol 11, No 4: August 2022 Vol 11, No 3: June 2022 Vol 11, No 2: April 2022 Vol 11, No 1: February 2022 Vol 10, No 6: December 2021 Vol 10, No 5: October 2021 Vol 10, No 4: August 2021 Vol 10, No 3: June 2021 Vol 10, No 2: April 2021 Vol 10, No 1: February 2021 Vol 9, No 6: December 2020 Vol 9, No 5: October 2020 Vol 9, No 4: August 2020 Vol 9, No 3: June 2020 Vol 9, No 2: April 2020 Vol 9, No 1: February 2020 Vol 8, No 4: December 2019 Vol 8, No 3: September 2019 Vol 8, No 2: June 2019 Vol 8, No 1: March 2019 Vol 7, No 4: December 2018 Vol 7, No 3: September 2018 Vol 7, No 2: June 2018 Vol 7, No 1: March 2018 Vol 6, No 4: December 2017 Vol 6, No 3: September 2017 Vol 6, No 2: June 2017 Vol 6, No 1: March 2017 Vol 5, No 4: December 2016 Vol 5, No 3: September 2016 Vol 5, No 2: June 2016 Vol 5, No 1: March 2016 Vol 4, No 4: December 2015 Vol 4, No 3: September 2015 Vol 4, No 2: June 2015 Vol 4, No 1: March 2015 Vol 3, No 4: December 2014 Vol 3, No 3: September 2014 Vol 3, No 2: June 2014 Vol 3, No 1: March 2014 Vol 2, No 4: December 2013 Vol 2, No 3: September 2013 Vol 2, No 2: June 2013 Vol 2, No 1: March 2013 Vol 1, No 4: December 2012 Vol 1, No 3: September 2012 Vol 1, No 2: June 2012 Vol 1, No 1: March 2012 List of Accepted Papers (with minor revisions) More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA