cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
Redaksi Jurnal Rekayasa Mesin Jurusan Teknik Mesin Fakultas Teknik, Universitas Brawijaya Jl. MT. Haryono 167 Malang, Jawa Timur Indonesia 65145
Location
Kota malang,
Jawa timur
INDONESIA
Rekayasa Mesin
Published by Universitas Brawijaya
ISSN : 23381663     EISSN : 24776041     DOI : 10.21776/ub.jrm
Core Subject : Engineering,
Mechanical Engineering
Rekayasa Mesin is published by Mechanical Engineering Department, Faculty of Engineering, Brawijaya, Malang-East Java-Indonesia. Rekayasa Mesin is an open-access peer reviewed journal that mediates the dissemination of academicians, researchers, and practitioners in mechanical engineering. Rekayasa Mesin accepts submission from all over the world, especially from Indonesia. Rekayasa Mesin aims to provide a forum for national and international academicians, researchers and practitioners on mechanical engineering to publish the original articles. All accepted articles will be published and will be freely available to all readers with worldwide visibility and coverage. The scope of Rekayasa Mesin are the specific topics issues in mechanical engineering such as design, energy conversion, manufacture, and metallurgy. All articles submitted to this journal can be written in Bahasa and English Language.
Arjuna Subject : -
Articles 11 Documents
 1   2 
Search results for , issue "Vol 4, No 3 (2013)" : 11 Documents clear
Optimasi Desain Metal Gasket Tipis Bentuk New Corrugated Untuk Kebutuhan Tekanan Kerja Rendah Dengan Simulasi Komputer Permanasari, Avita Ayu; Choiron, Moch. Agus; Purnowidodo, Anindito
Jurnal Rekayasa Mesin Vol 4, No 3 (2013)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (561.714 KB)

Abstract

Contact width and leakage had been used as the main parameter to optimize a new corrugated metal gasket for high working pressure. The leakage could be reduced as increasing the contact width. On the other hand, gaskets in piping for low pressure were used into distribution of water in the hotel. In this study, thin metal gasket is optimized by using simulation experiment. The design of experimentation (DOE) Taguchi method is used to analyze the effect of each parameter design and to predict optimal design of thin metal gasket. The L27 orthogonal array is concerned to design the experimental matrix for five factors with three levels. The five factors are thickness (t), pitch (p), over hang (OH), lip height (h), and radius convex (R). The observed value is denoted by using the slope of the curve of relationship between contact width and clamping load. The slope of curve is increased; it will be reduce the clamping load. The optimum design of thin metal gasket based on the results of each observed values is a model with thickness (t) = 0.3 mm, pitch (p) = 4 mm, over hang (OH) = 3 mm, lip height (h) = 0.4 mm, and radius convex (R) = 2.5 mm.Keywords: Contact width, leakage, Taguchi, optimum design

Page 2 of 2 | Total Record : 11

 1   2 

Filter by Year

2013 2013


Reset
Filter By Issues
All Issue Vol. 16 No. 3 (2025) Vol. 16 No. 2 (2025) Vol. 16 No. 1 (2025) Vol. 15 No. 3 (2024) Vol. 15 No. 2 (2024) Vol. 15 No. 1 (2024) Vol. 14 No. 3 (2023) Vol. 14 No. 2 (2023) Vol. 14 No. 1 (2023) Vol. 13 No. 3 (2022) Vol. 13 No. 2 (2022) Vol. 13 No. 1 (2022) Vol 12, No 2 (2021) Vol 12, No 1 (2021) Vol 11, No 3 (2020) Vol 11, No 2 (2020) Vol 11, No 1 (2020) Vol 10, No 3 (2019) Vol 10, No 2 (2019) Vol 10, No 1 (2019) Vol 9, No 3 (2018) Vol 9, No 2 (2018) Vol 9, No 1 (2018) Vol. 9 No. 1 (2018) Vol 8, No 3 (2017) Vol 8, No 2 (2017) Vol 8, No 1 (2017) Vol 7, No 3 (2016) Vol. 7 No. 2 (2016) Vol 7, No 2 (2016) Vol 7, No 1 (2016) Vol 6, No 3 (2015) Vol 6, No 2 (2015) Vol 6, No 1 (2015) Vol 5, No 3 (2014) Vol 5, No 2 (2014) Vol 5, No 1 (2014) Vol 4, No 3 (2013) Vol 4, No 2 (2013) Vol 4, No 2 (2013) Vol 4, No 1 (2013) Vol 3, No 3 (2012) Vol 3, No 3 (2012) Vol 3, No 2 (2012) Vol 3, No 1 (2012) Vol 3, No 1 (2012) Vol 2, No 3 (2011) Vol 2, No 2 (2011) Vol 2, No 1 (2011) Vol 1, No 3 (2010) Vol 1, No 2 (2010) Vol 1, No 1 (2010) More Issue