Article Per Year (5 Year)
p-Index From 2021 - 2026
0
P-Index
This Author published in this journals
All Journal International Journal of Renewable Energy Development
Chitsomboon, Tawit
Unknown Affiliation
Chemistry Energy

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
Effects of turbulence models and grid densities on computational accuracy of flows over a vertical axis wind turbine Chaiyanupong, Jaruwan; Chitsomboon, Tawit
International Journal of Renewable Energy Development Vol 7, No 3 (2018): October 2018
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.7.3.213-222

Abstract

Flows through a vertical axis wind turbine (VAWT) are very complex due to their inherent unsteadiness caused by large variations of the angle of attacks as the turbine is rotating and changing its azimuth angles simultaneously. In addition, a turbine must go through a wide range of operating conditions especially the change in blade speed ratio (BSR). Accurate prediction of flows over VAWT using Reynolds-Averaged Navier-Stokes (RANS) model needs a well-tested turbulence model as well as a careful grid control around the airfoil. This paper aimed to compare various turbulence models and seek the most accurate one. Furthermore, grid convergence was studied using the Roache method to determine the sufficient number of grid elements around the blade section. The three-dimensional grid was generated by extrution from the two-dimensional grid along with the appropriate y+ controlling. Comparisons were made among the three turbulence models that are widely used namely: the RNG model, the shear stress transport k-ω model (SST) and the Menter’s shear stress transport k-ω model (transition SST). Results obtained clearly showed that turbulence models significantly affected computational accuracy. The SST turbulence model showed best agreement with reported experimental data at BSR lower than 2.35, while the transition SST model showed better results when BSR is higher than 2.35. In addition, grid extruding technique with y+ control could reduce total grid requirement while maintaining acceptable prediction accuracy.Article History: Received April 15th 2018; Received in revised form June 16th 2018; Accepted September 17th 2018; Available onlineHow to Cite This Article: Chaiyanupong,J and Chitsomboon, T. (2018) Effects of Turbulence Models and Grid Densities on Computational Accuracy of Flows Over a Vertical Axis Wind Turbine. Int. Journal of Renewable Energy Development, 7(3), 213-222.http://dx.doi.org/10.14710/ijred.7.3.213-222 
Numerical Study of Effect of Blade Twist Modifications on the Aerodynamic Performance of Wind Turbine Beabpimai, Wiroj; Chitsomboon, Tawit
International Journal of Renewable Energy Development Vol 8, No 3 (2019): October 2019
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.8.3.285-292

Abstract

This paper aims to investigate aerodynamic performance of a wind turbine blade with twist modifications using computational fluid dynamics (CFD). The phenomenon of 3D stall-delay effect in relation to blade twist is the key feature to be investigated in order to improve efficiency of a wind turbine. The NREL (National Renewable Energy Laboratory) Phase VI wind turbine rotor was used for validation and as the baseline rotor. The baseline blade geometry was modified by increasing/decreasing the twist angles in the inboard, mid-board and outboard regions of the blade in the form of a symmetrical curve with maximum twist angle of 3°. The steady incompressible Reynolds-averaged Navier-Stokes (RANS) equations with the k-ω Shear Stress Transport (SST) turbulence closure model were used for the calculations at wind speeds ranging from 5-20 m/s. The computational results for the baseline Phase VI rotor were validated against experimental data and a good agreement was found. The computational results for the modified blades were compared against those of the baseline blade. It was found that increase of annual energy production of up to 5.1% could be achieved by this modification technique.  ©2019. CBIORE-IJRED. All rights reserved
Co-Authors Beabpimai, Wiroj Chaiyanupong, Jaruwan