Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

p-Index From 2021 - 2026

0.23

P-Index

This Author published in this journals

All Journal Jurnal Teknik ITS IPTEK Journal of Proceedings Series Journal of Civil Engineering

Irmawan, Mudji

Institut Teknologi Sepuluh Nopember

Author-ID : 1454656

Computer Science & IT Engineering

Published : 8 Documents Claim Missing Document

Claim Missing Document

Articles

Title

PHYSICAL AND MECHANICAL PROPERTIES LIGHTWEIGHT CONCRETE AND THE USE STYROFOAM SILICA SAND Kurdian Suprapto; Mudji Irmawan; Fauzi Rahman
Journal of Civil Engineering Vol 31, No 1 (2011)
Publisher : Institut Teknologi Sepuluh Nopember

The research is motivated rationale for reuse styrofoam waste (wrappers monitor) that is widely available on the ground that this cannot be destroyed or recycled. Utilization of waste is intended to not pollute the environment and can even be commercially valuable. In addition, this study is an attempt to find alternative materials replacement bricks. One of them is by using a mixture of portland cement, silica sand and styrofoam for the manufacture of non-structural lightweight concrete. Silica sand crushed into powder 22.44% retained on sieve no. 325 and styrofoam used in the form of small granules which pass 9.5 mm sieve. This study begins with a test mortar with silica sand content of 0%, 30%, 40%, 50% by weight of cement + silica sand. Then one of the mortar mixture composition is taken to be combined with Styrofoam to test concrete with styrofoam levels of 3%, 3.5%, 4% by weight of cement + silica sand. From the results of testing mortars, the composition of the mixture is taken as 40% silica sand and cement 60%. In testing the concrete, the greater the level of styrofoam, the smaller the volume weight, compressive strength, tensile strength and flexural strength concrete. The composition of concrete mixtures with styrofoam levels 3.5% and 4% which can be categorized as non-structural lightweight concrete material to be used as wall panels / insulation.

DUCTILITY EVALUATION OF REINFORCED CONCRETE COLUMN MADE OF NORMAL- TO HIGH-STRENGTH CONCRETE UNDER CONSTANT AXIAL LOAD LEVEL COMBINED WITH FLEXURAL LOADING USING NONLINEAR SECTIONAL FIBER BASED MODEL Bambang Piscesa; Dwi Prasetya; Mudji Irmawan; Harun Alrasyid
Journal of Civil Engineering Vol 34, No 1 (2019)
Publisher : Institut Teknologi Sepuluh Nopember

This study presents the ductility evaluation of reinforced concrete column made of normal-strength material using various empirical stress-strain model with nonlinear sectional fiber based analysis. The purpose is to evaluate the confinement requirement for reinforced concrete column under high axial load level. The concrete strength considered in the analysis are varies from 30 to 70 MPa while the steel reinforcing bar yield strength considered is only 400 MPa. The ductility is evaluated by using the customized ductility index measurement. The ratio of the concrete cover to the concrete core is set to 0.1 but not more than 40 mm. Attard and Setunge’s concrete constitutive model is used in this investigation. Cover spalling behavior is considered in the analysis by including the restrained shrinkage effect on the concrete strength and the softening behavior. From this study, it was found that extra confinement is necessary to maintain the expected minimum level of ductility.

Strength reduction factor evaluation of the circular reinforced concrete column with varying eccentricity ratio (e/h) Wahyuniarsih Sutrisno; Mudji Irmawan; Dwi Prasetya
Journal of Civil Engineering Vol 35, No 1 (2020)
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j20861206.v35i1.7788

This paper presents strength reduction factor evaluation of circular reinforced concrete column with varying eccentricity ratio (e/h) using the first-order-reliability-methods. The resistance properties of the reinforced concrete column is estimated using the monte-carlo simulation with random normally distributed material properties. Only dead and live load combination considered in the analysis. The parameters being investigated when evaluating the resistance of the reinforced concrete column are the concrete compressive strength, steel yield strength, coefficient of variation for both the concrete and steel materials, reinforced concrete column size, and the longitudinal reinforcement ratio. When evaluating the strength-reduction factor, the safety index values are 3.0, 3.5, and 4.0. From the analysis, it was found out that the strength reduction factor, for e/h higher than one and with safety index equal to 3.0, was equal to 0.9 which agrees well with the ACI 318 strength reduction factor for tension-controlled region. However, for e/h lower than one and safety index equal to 3.0, the strength reduction factor was equal to 0.6 which was lower than the ACI 318 strength reduction factor for compression-compression controlled region.

APPLICATION OF DIGITAL IMAGE CORRELATION TO CAPTURE THE CRACK MOUTH OPENING DISPLACEMENT OF THE NOTCHED STEEL FIBER REINFORCED CONCRETE (SFRC) BEAM Mudji Irmawan; Bambang Piscesa; Priyo Suprobo; Harun Al Rasyid
Journal of Civil Engineering Vol 37, No 2 (2022)
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j20861206.v37i2.14046

The application of digital image correlation (DIC) to capture any point in the experimental test is found to be promising. Using the DIC and appropriate tool can overcome the limitation of the traditional sensors to capture the movement or displacement in the tested specimen. In this study, an open-source DIC called Digital Image Correlation Engine (DICE) is used to capture the crack mouth opening displacement (CMOD) of the notched steel fiber reinforced concrete (SFRC) beam with points tracking method. There are three beam specimens with different sizes and similar aspect ratios reported in this paper. All beams have 0.5% steel fiber volumetric content. The SFRC beams are marked with points and tested under a three-point bending flexural test. Custom firmware for Canon DSLR 650D digital camera called Magic Lantern is used to capture the pictures per one second. DICE software is used to analyze the point movements and dumped the output file. ParaView 5.9.0 is then used to visualize the data. A method to calibrate the point coordinate with actual measurement is proposed. A small script is written in Visual Basic Application (VBA) in Microsoft Excel to correlate the displacement for each point of interest with the recorded applied load. With the developed script, any point of interest tracked with DICE can be related to the recorded data from the data logger. From this study, the obtained CMOD with the corresponding applied load is presented, which can be used to investigate the flexural fracture energy of the SFRC beam.

Co-Authors Alrasyid, Harun Bambang Piscesa Darmawan, Muhammad Sigit Endah Wahyuni Fauzi Rahman FX Teddy Badai Samodra Harun Al Rasyid Krisdianto, Johanes Kurdian Suprapto Kusuma Indra Klana Prasetya, Dwi Priyo Suprobo Refani, Afif Navir Wahyuniarsih Sutrisno Yerry Kahaditu Firmansyah

Title Search

Found 4 Documents Search Journal : Journal of Civil Engineering

Abstract

Abstract

Abstract

Abstract

Title

Found 4 Documents
Search
Journal : Journal of Civil Engineering