Article Per Year (5 Year)
p-Index From 2020 - 2025
0.444
P-Index
This Author published in this journals
All Journal Communications in Science and Technology
Fadhillah, Farid
Unknown Affiliation
Engineering

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search
Journal : Communications in Science and Technology

 1 
Thin film composite polyelectrolyte multilayer nanofiltration membrane fabricated using spin assisted layer by layer assembly: Application of solution diffusion film model Alghamdi, Ahmad; Fadhillah, Farid
Communications in Science and Technology Vol 5 No 1 (2020)
Publisher : Komunitas Ilmuwan dan Profesional Muslim Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (998.886 KB) | DOI: 10.21924/cst.5.1.2020.177

Abstract

Thin Film Composite (TFC) Polyelectrolyte Multilayer (PEM) Nanofiltration (NF) membrane consisting of multilayer of Poly(diallyl dimethyl ammonium chloride) (PDAC) and Poly(sodium 4-styrenesulfonate) (PSS) deposited on polyethersulfone (PES) support was prepared using spin-assisted layer by layer assembly (SA-LbL). This work is an effort to discover new material having better characteristics and performance than commercial polyamide (PA) NF membrane. Two main operating conditions namely temperature and salt concentration were investigated and the effect of both on membrane performance was studied. Solution-diffusion Film Model (SDFM) membrane employing two fitting parameters i.e. membrane salt permeability (PS) and stagnant layer salt permeability PS(d), was used to explain membrane transport across the membrane. The result showed an good agreement between experimental and observed rejection rate suggests PEM membrane behaves similar to typical solution diffusion-type composite membrane and SDFM can be used to predict the membrane performance and behavior.
Domestic waste (eggshells and banana peels particles) as sustainable and renewable resources for improving resin-based brakepad performance: Bibliometric literature review, techno-economic analysis, dual-sized reinforcing experiments, to comparison ... Nandiyanto, Asep Bayu Dani; Ragadhita, Risti; Fiandini, Meli; Al Husaeni, Dwi Fitria; Al Husaeni, Dwi Novia; Fadhillah, Farid
Communications in Science and Technology Vol 7 No 1 (2022)
Publisher : Komunitas Ilmuwan dan Profesional Muslim Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21924/cst.7.1.2022.757

Abstract

The objective of this study is to develop a new environmentally-friendly brake pad made from eggshells (Es) and banana peels (BPs) as reinforcement agents. E and BP particles as dual reinforcement with various compositions were combined. The E/BP mixture was then embedded on a polymer matrix composing a resin/hardener mixture in a 1:1 ratio. As a standard, brake pads using a single reinforcement of E and BP particles were also fabricated. Physical properties (i.e. particle size, surface roughness, morphology, and density), as well as mechanical properties (i.e. hardness, wear rate, and friction coefficient properties) were investigated. It was observed that using dual reinforcements was preferable (compared to using single reinforcements) because they had a synergistic effect on the mechanical properties of the brake pad. The best mechanical properties were found in dual reinforcements of brake pad specimens using E/BP particles with a higher BP ratio in which the value of the stiffness test, puncture test, wear rate, and coefficient of friction were 4.5 MPa, 86.80, 0.093×10-4 g/s.mm2, and 1.67×10-4, respectively. A high BP particle ratio played a dominant role in dual reinforcements, increasing the resin's bonding ability and resulting in good adhesion between the reinforcement and matrix. When compared to commercial brake pads, the brake pad specimens fabricated in this study met the standards. The techno-economic analysis also confirmed the prospective production of brake pads from E and BP particles (compared to commercial brake pads). From this research, it is expected that environmentally friendly and low-cost brake pads can be used to replace the dangerous friction materials.
Co-Authors Al Husaeni, Dwi Fitria Al Husaeni, Dwi Novia Alghamdi, Ahmad Asep Bayu Dani Nandiyanto Fiandini, Meli Ragadhita, Risti