Article Per Year (5 Year)
p-Index From 2021 - 2026
0.562
P-Index
This Author published in this journals
All Journal Journal of Applied Science, Engineering, Technology, and Education
Chavali, Murthy
Unknown Affiliation
Civil Engineering, Building, Construction & Architecture Computer Science & IT Electrical & Electronics Engineering Industrial & Manufacturing Engineering Other

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Nanotechnology for Mitigating Impact of COVID-19 Tripathi, Dr. Gagan Kant; Rathore, Harshit; Chavali, Murthy; Rathore, Deepshikha
Journal of Applied Science, Engineering, Technology, and Education Vol. 3 No. 2 (2021)
Publisher : Yayasan Ahmar Cendekia Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (538.786 KB) | DOI: 10.35877/454RI.asci151

Abstract

This review article aims to create awareness towards COVID-19 epidemic and develop a basic responsibility in human beings to control and stop the transmission of COVID-19. It has been highlighted that disaster is imminent if we play with nanostructures unknowingly. The effect of COVID-19 on mankind and its detection and transmission have also been discussed briefly. The protection guidelines including treatment procedures have been illustrated. The utilization of nanoparticles to detect and cure COVID-19 has been described.
Novel eco-friendly linear gel for oil well recovery through efficient hydrofracturing Murthy, R. V. V. Ramana; Murthy, K. S. R.; Chavali, Murthy
Journal of Applied Science, Engineering, Technology, and Education Vol. 3 No. 2 (2021)
Publisher : Yayasan Ahmar Cendekia Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (490.439 KB) | DOI: 10.35877/454RI.asci165

Abstract

The linear gel is prepared by treating bio-diesel with various water samples collected from different water bodies. The new biodiesel based linear gel was employed in the recovery of oil wells through hydrofracturing and pilot tests were conducted for the first time. The viscosity of gel was measured at various bottom hole-circulating temperatures and it was found to vary from 32 to zero dial reading in the range of 45ºC to 60ºC. The gel was observed to break at 45ºC and 60ºC in 120 min. So the final temperature was selected as 60ºC for the application of gel for coal bed methane (CBM) wells. It was observed that higher levels of salinity in water helped in optimum utilization of gel in real-time application.
Design and development of instant linear gel for coal bed methane gas operations Murthy, R. V. V. Ramana; Murthy, K. S. R.; Chavali, Murthy
Journal of Applied Science, Engineering, Technology, and Education Vol. 3 No. 2 (2021)
Publisher : Yayasan Ahmar Cendekia Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (800.652 KB) | DOI: 10.35877/454RI.asci167

Abstract

Linear gel fracturing fluids are expressed with an extensive range of materials/polymers in an aqueous base. Earlier we developed fracturing linear gel with fossil diesel, bio-diesel and also used suspending anti-settling agents and emulsifiers. Here we report on a novel and an efficient method for the preparation of linear gel direct mix with water, guar gum and sodium acetate together instantly. In this research work, we used water instead of diesel without any need to mix anti-settling agents, suspending agents, emulsifiers that resulted in 30 viscosity linear gel. The degradation pattern observed from the breaker test showed that a reduction in gel viscosity depends on time, temperature & breaker concentration. Ammonium per sulphate or Ammonium per oxidisulphate and enzyme-G were used for oxidation purpose to break the gel gradually at a particular static temperature. Observations from experiments revealed that a small concentration of breaker provides rapid break compared to oxidative breakers. This article, designing of fracturing fluids describes how to use the fluid's viscosity generated by the gelling agents like guar gum for CBM operations.
Co-Authors Murthy, K. S. R. Murthy, R. V. V. Ramana Rathore, Deepshikha Rathore, Harshit Tripathi, Dr. Gagan Kant