Claim Missing Document
Check
Articles

Found 3 Documents
Search

Bandage Effect Antiaging Cream Channa Striata Extract (Snakehead Fish) With Tretinoin Cream 0.1% Against Photoaging Indrawan, Yudi; Putri, Arridha Hutami
Buletin Farmatera Vol 10, No 3 (2025)
Publisher : Universitas Muhammadiyah Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30596/bf.v10i3.24635

Abstract

Abstract: Photoaging is a skin aging process that occurs due to sun exposure causing damage to the skin. From the results of the study, it was also found that the most visible signs of premature aging were not fine lines or wrinkles, but dull skin with a percentage of 53.30%. Snakehead fish has a protein level in 100 grams of fish meat reaching 25.2 grams. The albumin level of snakehead fish is quite high up to 6.22%, and the zinc mineral content from snakehead fish reaches 1.74 mg/100 grams, with high levels of protein and albumin snakehead fish useful as photoaging therapy. This study aims to find out whether there is a difference in effect between the use of Channa striata (snakehead fish) extract cream and 0.1% tretinoin cream as photoaging therapy. This type of study is a randomized control trial using 2 groups, namely the group with the administration of snakehead fish cream test material and the group with the 0.1% tretinoin cream test material for 30 days with a total sample of 96 people, each sample will be observed at the beginning and end of the treatment using the Glombau scale. Based on the results of the study, there was no difference in effectiveness between the use of Channa Striata (snakehead fish) extract cream and 0.1% tretinoin cream on photoaging (p=1.00). There was no comparison of effectiveness between the use of Channa Striata (snakehead fish) extract cream and 0.1% tretinoin cream on photoaging.
Analisis Kontribusi Keuntungan Atas Produk-Produk Pada Toko Kaca Dan Alumunium Ridho Utama Di Tenggarong (Penerapan Linear Programming Metode Simpleks) Indrawan, Yudi; Iskandar, Iskandar; S, Syahhruddin
JEMI is managed and published by the Management Study Program, Faculty of Economics and Business, Kutai Kartanegara University. Institutional legality is reflected in the ISSN number: 1411-9560 published by LIPI in 2003 as a manifestation of the comm Vol 16 No 2 (2016)
Publisher : FAKULTAS EKONOMI DAN BISNIS UNIKARTA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.53640/jemi.v16i2.224

Abstract

The main objective of this study was to find out what is the optimum amount of production to generate maximum profit contribution for the products produced by Ridho Utama glass and Aluminum shop in Tenggarong. A series of observations carried out on the object of research is  Ridho Utama glass and Aluminum shop in Tenggarong where the company is going to take maximum advantage of two combinations of product that the product stove door (A3) and the product of the wardrobe (A8) with the respective number of optimal production was 7, 1883 or rounded up to 7 units and 33.215 or rounded to 33 units to generate the maximum profit of Rp 65,314,580, - or with rounded figure was Rp 64.750.000, for the glass installation-time or process 3 (S3) and mounting rubber or poccess 4 (S4) respectively still leave time for 590.1001 minutes it indicates that the company can save time on the 3 and 4 respectively during 590.1001 minutes or can be totaled 1180.2002 or 19,67 hours for 3 months. Another case for products that have the status of non basic or value equal to 0 (zero) it means that other product is better not manufactured by the company because it does not produce the maximum profit. Then the hypothesis has been stated previously that states "That the production of glass and Aluminum shop Ridho Utama in Tenggarong has been optimized so that produce the maximum profitKeywords: Profit Contributions(Application of Linear Programming Simplex Method)
Analisis Kontribusi Keuntungan Atas Produk-Produk Pada Toko Kaca Dan Alumunium Ridho Utama Di Tenggarong (Penerapan Linear Programming Metode Simpleks) Indrawan, Yudi; Iskandar, Iskandar; S, Syahhruddin
JEMI is managed and published by the Management Study Program, Faculty of Economics and Business, Kutai Kartanegara University. Institutional legality is reflected in the ISSN number: 1411-9560 published by LIPI in 2003 as a manifestation of the comm Vol 16 No 2 (2016)
Publisher : FAKULTAS EKONOMI DAN BISNIS UNIKARTA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.53640/jemi.v16i2.224

Abstract

The main objective of this study was to find out what is the optimum amount of production to generate maximum profit contribution for the products produced by Ridho Utama glass and Aluminum shop in Tenggarong. A series of observations carried out on the object of research is  Ridho Utama glass and Aluminum shop in Tenggarong where the company is going to take maximum advantage of two combinations of product that the product stove door (A3) and the product of the wardrobe (A8) with the respective number of optimal production was 7, 1883 or rounded up to 7 units and 33.215 or rounded to 33 units to generate the maximum profit of Rp 65,314,580, - or with rounded figure was Rp 64.750.000, for the glass installation-time or process 3 (S3) and mounting rubber or poccess 4 (S4) respectively still leave time for 590.1001 minutes it indicates that the company can save time on the 3 and 4 respectively during 590.1001 minutes or can be totaled 1180.2002 or 19,67 hours for 3 months. Another case for products that have the status of non basic or value equal to 0 (zero) it means that other product is better not manufactured by the company because it does not produce the maximum profit. Then the hypothesis has been stated previously that states "That the production of glass and Aluminum shop Ridho Utama in Tenggarong has been optimized so that produce the maximum profitKeywords: Profit Contributions(Application of Linear Programming Simplex Method)