USEP ALI ALBAYUMI
Teknik Elektro Institut Teknologi Nasional (ITENAS) Bandung

Published : 7 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search
Journal : REKA ELKOMIKA

Perancangan dan Pembuatan PLC-MIKRO untuk Model Flap dengan Feedback Potensiometer Berbasis Microcontroller PIC16F877A IMANDA, SEMADHI ADHI; NATALIANA, DECY; ALBAYUMI, USEP ALI
REKA ELKOMIKA Vol 2, No 3 (2014)
Publisher : REKA ELKOMIKA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1464.319 KB)

Abstract

Abstrak Flap pada sayap pesawat merupakan salah satu komponen dalam sistem pesawat terbang yang menghasilkan gaya angkat atau High Lift Device. Beberapa sistem ini menggunakan electromechanic system. Penelitian ini mencoba menggantikan electromechanic system tersebut menjadi suatu sistem yang dapat dikendalikan secara terpusat dengan menggunakan PLC-mikro. Sistem yang diimplementasikan berupa model flap sayap pesawat yang bekerja berdasarkan instruksi dari ladder diagram yang diprogram menggunakan software LDmicro. PLC-mikro akan mengirimkan perintah pada motor stepper, motor stepper akan bergerak searah ataupun berlawanan arah jarum jam menuju posisi flap yang diinginkan. Terdapat sebuah potensiometer yang berfungsi sebagai sensor posisi. Dilakukan pengujian terhadap prototype flap sayap pesawat terbang dan berhasil menggerakkan motor stepper berputar searah jarum jam maupun berlawanan dengan arah jarum jam, memberikan informasi posisi flap sempurna dari pesawat. Sistem ini juga berhasil membaca informasi posisi flap pesawat dari potensiometer. Kata Kunci : Flap, Motor Stepper, PLCmikro, LDmicro, Ladder Diagram. Abstract Flap is the most important device to make a high-lift in an airplane. It device can make a high-lift called High Lift Device. Some of high-lift systems using an electromechanic system. This research tried to replace the electromechanic system into a system that could be controlled centrally by using a PLC-mikro. The system was implemented in a flap model that worked based on the instruction of the ladder diagram. It program used LDmicro software. PLCmikro would give a command to a motor stepper, and it will move the prototype to a desired position. Potensiometer was an analog input model of the sensor position. Flap prototype was realized successfully driving the stepper motor to rotate in clockwise or counter-clockwise, giving information a perfect flap of the aircraft. The system was also able to read information from the aircraft flap position potentiometer. Keywords: Flap, Motor Stepper, PLCmikro, LDmicro, Ladder Diagram.
Prototype Synopsis Page pada Model Landing Gear System Pesawat Terbang dengan Kontrol PLCmikro PIC16F877A dan Aplikasi HMI Stampplot ADRIAN, SANDY RACHMAN; NATALIANA, DECY; ALBAYUMI, USEP ALI
REKA ELKOMIKA Vol 2, No 3 (2014)
Publisher : REKA ELKOMIKA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1414.636 KB)

Abstract

Abstrak Sistem monitoring roda pesawat untuk satu kondisi roda pesawat yang ada saat ini dibutuhkan beberapa komponen elektrik maupun mekanik agar pilot dapat mengerti informasi tentang keadaan roda. Untuk itu diperlukan adanya suatu sistem monitoring yang lebih sederhana namun dapat memberikan pilot sebuah informasi roda pesawat yang lebih baik. Tujuan penelitian ini adalah merancang dan merealisasikan sebuah purwarupa dari synopsis page roda pesawat terbang yang dikontrol oleh PLCmikro. Sistem ini menampilkan status roda pesawat terbang dalam berbagai macam kondisi, saat pesawat di landasan, saat pesawat lepas landas, saat pesawat di udara, saat pesawat mendarat dan saat pesawat mengalami kegagalan fungsi. PLCmikro difungsikan sebagai alat kontrol sedangkan synopsis page difungsikan sebagai alat monitoring roda pesawat. Pengujian dilakukan dengan mengintegrasikan PLCmikro dengan aplikasi Stampplot kemudian hasil pengujian dilihat pada tampilan synopsis page. Didapatkan kesimpulan bahwa sistem monitoring dapat bekerja dengan baik dengan respon rata-rata kurang dari 1 detik sesuai dengan kondisi roda pesawat yang beroperasi. Kata kunci : Synopsis Page, roda pendarat, roda pesawat, PLCmikro Abstract A current plane landing gear monitoring system for one condition needs some electrical and mechanical components so that a pilot can get some information about the state of the wheel. That’s why we need more simpler monitoring system that can give the pilot more information. The purposes of this research were to design and create a prototype of synopsis page landing gear system that controlled by PLCmicro. This system would display of status of airplane wheels in various conditions, start from the airplane on the ground, takeoff, in the air, landing and when the system was malfunction. PLCmicro was used as a controller while the synopsis page was used as a monitor of landing gear. The test for this system was done by integrating PLCmicro with Stampplot then the results of the test could be displayed in the synopsis page. It could be concluded that the monitoring system could work well less than 1 second in accordance with the operating conditions of airplane wheels. Keywords : Synopsis Page, landing gear, airplane wheels, PLCmicro