Garuda - Garba Rujukan Digital

Acquiring higher lumen efficacy and color rendering index with green NaYF4:Er3+Yb3+ and red α-SrO·3B2O3:Sm2+ layers for designing remote phosphor LED My Hanh Nguyen Thi; Nguyen Thi Phuong Loan; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 6: December 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i6.13796

Lighting devices that apply diodes to create white light-emitting diodes (WLEDs) can achieve remarkable results in color quality, especially those containing quantum dots (QDs) and phosphor. The technique to create an appropriate package is providing spaces between the QDs and phosphor components which helps decrease the ratio of the reabsorption losses and keeps the QDs surface ligands constant. The research aims to perfect the constructing method of remote phosphor configuration containing quantum dots and phosphor materials that based on lighting properties and temperature feature of WLEDs. The infrared thermography is the tool to measure and analyze total emitted light and emission ranges of the device. This device is also used in temperature simulation and experimental verification. At the given mA of 60, the WLEDs structure with green QDs layer above the phosphor layer results in 996 lm luminous flux (LF), and Ra = 57 in color rendering ability. Meanwhile, luminous flux of WLEDs with red QDs-on-phosphor structure is 632, and Ra = 70. Furthermore, comparing with the green QDs-on-phosphor type, the red QDs-on-phosphor type emitted less LF. However, the red QDs-on-phosphor type can be the most effective package design to achieve color rendering ability.

TiO2/silicone encapsulation film for achieving optical performance improvement of chip-on-board packaging LEDs My Hanh Nguyen Thi; Phung Ton That
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 2: April 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i2.16755

TiO2 nanoparticle and silicon composite has powerful effect of scattering, thus it is famous in enhancing the scattered light in light-emitting diode (LED) packages. To accomplish higher lighting performance in LED devices, a thin encapsulation layer of TiO2 with high concentration and silicon glue is introduced to complement the main encapsulation one. After conducting experiments, the results present that in the case of the main encapsulation including only silicone, the light extraction efﬁciency (LEE) of COB LEDs increases to 65%. On the other hand, when there is the additional layer of TiO2 and silicone, the improvement of LEE depends on the concentration of TiO2. As this nanoparticle concentration decreases from 0.12 to 0.035 g/cm3, the LEE can be enhanced from 6% to 24%. Moreover, at the average correlated color temperature (CCT) of approximately 8500 K, the layer of TiO2/silicone composite can help to accomplish the reduction of the angular correlated color temperature (CCT) deviation, from 900 to 470 K, within −90° to 90° viewing angle range.

Investigation on the application of ZnO nanostructures to improve the optical performance of white light-emitting diodes My Hanh Nguyen Thi; Phung Ton That; Hoang Van Ngoc
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 3: June 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i3.16714

Though combining blue LED chips with yellow phosphor has been the most common method in white light-emitting diode (WLED) production, the attained angular correlated color temperature (CCT) uniformity is still poor. Thus, this article proposes to add ZnO nanostructures to WLED packages to promote the color uniformity of the WLEDs. The outcomes of the research demonstrate that utilizing ZnO at different amount can affect the scattering energy and the CCT deviations in WLEDs packages in different extents. Particularly, adding the node-like (N-ZnO), sheet-like (S-ZnO), and rod-like (R-ZnO) leads to the corresponding decreases of CCT deviations from 3455.49 K to 96.30 K, 40.03 K, and 60.09 K, respectively. Meanwhile, with 0.25% N-ZnO, 0.75% S-ZnO, and 0.25 % R-ZnO, WLED devices can achieve both better CCT homogeneity and lower reduction in luminous flux. The results of this article can be a valuable document for the manufacturer to use as reference in improving their WLED products.

Improving optical properties of remote phosphor LED using green Y2O3:Ho3+ and red Mg4(F)(Ge, Sn)O6:Mn2+ layers My Hanh Nguyen Thi; Nguyen Thi Phuong Loan; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 6: December 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i6.13797

The lighting device that employs diodes to create white light (WLEDs) with quantum dots (QDs) and phosphor layers is a promising lighting method that is increasingly used in many fields on account of the remarkable color expressing ability. The QDs film is usually placed apart from the phosphor layer according to the packaging configuration to prevent light loss due to backscattering as well as preserve the consistency of the ligands on the QDs surface. The article also conducted experiments to compare the lighting properties and thermal output of the two packaging orders of QDs and phosphor. The heat discharing ranges were simulated with thermography technology, moreover, other parameters such as light energy emission and PL spectra are acquired to evaluate the efficiency of the packaging order. The results from the practical experiment show that while under 10% wt., the luminous output (LO) of green QDs-on-phosphor structure reaches 1130 lm, higher than the red QDs-on-phosphor structure with 878 lm, and the color rendering value in the configuration with red QDs on phosphor is Ra = 74 are higher than Ra = 68 index of the green QDs-on-phosphor structure. As a result, the QDs-on-phosphor is determined as the better packaging configuration to choose to achieve an overall improvement in lighting efficiency, color rendering index

Study of red-emitting LaAsO4:Eu3+ phosphor for color rendering index improvement of WLEDs with dual-layer remote phosphor geometry My Hanh Nguyen Thi; Nguyen Thi Phuong Loan; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 6: December 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i6.13637

The remote phosphor structure is often disadvantageous in color quality but in terms of optics it is more convenient when compared to other phosphor structures such as conformal or in-cup ones. From this disadvantage, there are many studies to improve its chromatic output. In this research paper, we propose a dual-layer remote phosphor geometry for the improvement of white light-emitting diodes (WLEDs) in two parameters: color rendering index (CRI) and color quality scale (CQS). The 7700 K WLEDs are used in this study. The idea of the study is to place a red phosphor layer LaAsO4:Eu3+ on the yellow phosphor YAG: Ce3+, and then find the concentration of LaAsO4:Eu3+ in an appropriate way to achieve the highest color quality. The results showed that LaAsO4:Eu3+ bring great benefits for enhancing CRI and CQS. In particular, the greater the concentration of LaAsO4:Eu3+, the greater the CRI and CQS because the portion of red lights in WLEDs increases. However, the decrease in lumen output occurs when the concentration of LaAsO4:Eu3+ increases excessively. This is proved thanks to Mie-scattering theory and Beer-Lambert law. The results of important articles in WLEDs fabrication have greatly contributed to a higher white light quality.

The application of dual-layer remote phosphor geometry in achieving higher color quality of WLEDs My Hanh Nguyen Thi; Phung Ton That; Hoang Van Ngoc
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 2: April 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i2.16706

If remote phosphor structures are put into comparison with conformal phosphor or in-cup phosphor, their luminous flux are better, but the color quality is not as elevated. This leads to an obvious need of a practical solution to enhance color quality. Therefore, many studies were carried out to achieve this purpose, and so is ours. We proposed using two layers of phosphor in WLEDs to achieve better rendering ability and chromatic performance. The identical WLEDs with different color temperatures, 5600 K-8500 K, were used and reported in this paper. Our research consists of two parts, which are placing a layer of red phosphor SrwFxByOz:Eu2+,Sm2+on the yellow YAG:Ce3+ phosphor layer at first, and then specifying an appropriate SrwFxByOz:Eu2+,Sm2+ concentration to reach the highest color performance. It is shown that with the contribution of SrwFxByOz:Eu2+,Sm2+,the color rendering index (CRI) and color quality scale (CQS) are increased. This can be explained by the increased amount of red light components in the WLEDs when the concentration of SrwFxByOz:Eu2+,Sm2+ was greater. However, excessive SrwFxByOz:Eu2+,Sm2+ will cause the reduction in the flux, which has been proven by the application of Mie scattering and the Lambert-Beer law. Therefore, the conclusion will present an optimal amount of SrwFxByOz:Eu2+,Sm2+ to obtain high color quality while minimizing the light loss.

Using flat phosphor layer in dual-layer remote phosphor configuration to improve luminous efficacy My Hanh Nguyen Thi; Phung Ton That; Tri-Vien Vu
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 3: June 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i3.16349

The phosphor layer shape and components distances are the subjects proposed to advance the quality of WLEDs in this article. The two distances, between phosphor layers (d1) and between the phosphor layer and the LED chip (d2) in Flat dual-remote phosphor (FDRP) and Concave dual-remote phosphor (CDRP) were examined by experiments to determine their impacts on WLEDs lighting performances. The results suggest that FDRP is a better option than CDRP for lighting performance. In each respective structure, the distances influence the lighting capacity and color output whenever they fluctuate. Therefore, to effectively control and study this phenomenon, the correlated color temperature is maintained at 8500 K, and the concentration of phosphor material is altered while the distances are changing. When d1 and d2 are at the starting value of 0, the recorded lumen output and chromatic performance of lighting devices are the lowest and begin to increase as d1 and d2 expand. Bigger d1 and d2 mean bigger scattering area and better chromatic light integration, which leads to higher color quality. Detailed results present that optimal values of d1 or d2 for the highest lumen output of 1020 lm are 0.08 mm or 0.63 mm, respectively. Meanwhile the lowest color deviation is accomplished with d1=0.64 mm or d2=1.35 mm.

The application of green YF3:Er3+,Yb3+ and red MgSr3Si2O8:Eu2+,Mn2+ layers to remote phosphor LED My Hanh Nguyen Thi; Nguyen Thi Phuong Loan; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 6: December 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i6.13827

White light-emitting diodes (WLEDs) with quantum dots (QDs) and phosphor have pulled in huge consideration because of their incredible shading rendering capacity. In the bundling procedure, a QDs film and a phosphor silicone layer will in general be isolated for lessening the reabsorption misfortunes and keeping the QDs surface molecules in a good condition. This examination explored the bundling succession of QDs and phosphor layers to the optical and warm exhibitions of WLEDs. The emitted optical power and PL spectra were estimated and dissected, while an infrared warm imager was utilized to reenact and approve tentatively the temperature fields. The results reveal that at 60 mA, WLEDs with green QDs-on-phosphor type accomplished lumen output (LO) of 1578 lm, with shading rendering record (CRI) of Ra = 60, while the red QDs-on-phosphor type WLEDs exhibited lower LO of 1000 lm, with Ra = 82. In addition, the QDs-onphosphor type WLEDs generated less warmth than the other, and as a result, the most noteworthy temperature in this packaged type was lower than the other. Additionally, its temperature contrast can arrive at 12.3°C. Along these lines, regarding bundling arrangement, the QDs-on-phosphor type is an ideal bundling design to better the optical productivity and shading rendering capacity, as well as lower gadget temperature.

The application of green YPO4:Ce3+,Tb3+ and red LiLaO2:Eu3+ layers to remote phosphor LED My Hanh Nguyen Thi; Nguyen Thi Phuong Loan; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 6: December 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i6.13647

Remote phosphor structure is commonly limited in color quality, but has greater luminous flux when comparing to structures with in-cup or conformal coating. From this dilemma, various researches with advance modifications have been proposed to perfect the chromatic performance of remote structure. In this research, we reach higher color quality by obtaining better values in quality indcators such as color rendering index (CRI) and color quality scale (CQS) with the dual-layer phosphor in our remote white light-emitting diodes (WLEDs). The idea is to ultize WLEDs with 7000 K correlated color temperature (CCT) and create dual-layer configuration with yellow phosphor YAG:Ce3+ under green phosphor YPO4:Ce3+,Tb3+ or red phosphor LiLaO2:Eu3+. After that, we search for suitable concentration of LiLaO2:Eu3+ for addition in order to acquire the finest color quality. The result shows that WLED with LiLaO2:Eu3+ has better CRI and CQS as the higher the concentration of LiLaO2:Eu3+, the larger CRI and CQS due to increased light scattered in WLEDs. Meanwhile, the green phosphor layer YPO4:Ce3+,Tb3+ give advantages to luminous flux. However, the reduction in luminous flux and color quality occurs when the concentration of LiLaO2:Eu3+ and YPO4:Ce3+,Tb3+ over increase. Results are verified by Mie theory and Beer’s Law and can be applied to practical manufacturing of high quality WLEDs.

Enhancement of luminous flux and color quality of white light-emitting diodes by using green (Y,Gd)BO3:Tb3+ phosphor My Hanh Nguyen Thi; Phung Ton That; Nguyen Doan Quoc Anh
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 3: June 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i3.15746

In the study, we analyzed and clarified the effect of green (Y,Gd)BO3:Tb3+ phosphor on chromatic homogeneity and optical performance of multi-chip white LEDs (MCW-LED). Thereby there is a solution to get the best luminous efficiency. In addition, (Y,Gd)BO3:Tb3+ is known as one of the factors that has a significant impact on lighting performance, so it needs to add the (Y,Gd)BO3:Tb3+ phosphor in the structure of LEDs to combine with the yellow phosphor YAG:Ce3+ to receive the best results. Therefore, the concentration and size of (Y,Gd)BO3:Tb3+ should be choose carefully so that the presentation of MCW-LEDs would be more incredible. The results show that when the concentration of green-emitting (Y,Gd)BO3:Tb3+ phosphor tends to increase, it also helps the color homogeneity and the lumen efficiency of MCW-LEDs with the average correlated color temperature (CCT) of 5600 K-8500 K become better.

Title

Found 13 Documents
Search
Journal : TELKOMNIKA (Telecommunication Computing Electronics and Control)

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 13 Documents Search Journal : TELKOMNIKA (Telecommunication Computing Electronics and Control)

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 13 Documents
Search
Journal : TELKOMNIKA (Telecommunication Computing Electronics and Control)