Article Per Year (5 Year)
p-Index From 2020 - 2025
0
P-Index
This Author published in this journals
All Journal International Journal of Power Electronics and Drive Systems (IJPEDS)
M. S. Chye
Universiti Malaysia Perlis
Control & Systems Engineering Electrical & Electronics Engineering

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Non-iterative Wide-modulation-index Switching-angle Calculation Techniques for 15-level Binary Cascaded H-bridge Multilevel Inverter J. A. Soo; M. S. Chye; Y. C. Tan; S. L. Ong; J. H. Leong; T. Sutikno
International Journal of Power Electronics and Drive Systems (IJPEDS) Vol 8, No 1: March 2017
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijpeds.v8.i1.pp93-99

Abstract

Cascaded H-bridge multilevel inverter (CHBMI) is able to generate a staircase AC output voltage with low switching losses. The switching angles applied to the CHBMI have to be calculated and arranged properly in order to minimize the total harmonic distortion (THD) of the output voltage waveform. In this paper, two non-iterative switching-angle calculation techniques applied for a 15-level binary asymmetric CHBMI are proposed. Both techniques employ a geometric approach to estimate the switching angles, and therefore, the generated equations can be solved directly without iterations, which are usually time-consuming and challenging to be implemented in real-time. Apart from this, both techniques are also able to calculate the switching angles for a wide range of modulation index. The proposed calculation techniques have been validated via MATLAB simulation and experiment.
Single-phase Multilevel Inverter with Simpler Basic Unit Cells for Photovoltaic Power Generation M. S. Chye; J. A. Soo; Y. C. Tan; M. Aizuddin; S. Lee; M. Faddle; S. L. Ong; T. Sutikno; J. H. Leong
International Journal of Power Electronics and Drive Systems (IJPEDS) Vol 7, No 4: December 2016
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijpeds.v7.i4.pp1233-1239

Abstract

This paper presents a single-phase multilevel inverter (MLI) with simpler basic unit cells. The proposed MLI is able to operate in two modes, i.e. charge mode to charge the batteries, and inverter mode to supply AC power to load, and therefore, it is inherently suitable for photovoltaic (PV) power generation applications. The proposed MLI requires lower number of power MOSFETs and gate driver units, which will translate into higher cost saving and better system reliability. The power MOSFETs in the basic unit cells and H-bridge module are switched at near fundamental frequency, i.e. 100 Hz and 50 Hz, respectively, resulting in lower switching losses. For low total harmonic distortion (THD) operation, a deep scanning method is employed to calculate the switching angles of the MLI. The lowest THD obtained is 8.91% at modulation index of 0.82. The performance of the proposed MLI (9-level) has been simulated and evaluated experimentally. The simulation and experimental results are in good agreement and this confirms that the proposed MLI is able to produce an AC output voltage with low THD.
MATLAB/Simulink modelling and simulation of 9-level cascaded h-bridge multilevel inverter with mismatched DC sources W. V. Yong; M. S. Chye; Y. C. Tan; S. L. Ong; J. H. Leong
International Journal of Power Electronics and Drive Systems (IJPEDS) Vol 10, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijpeds.v10.i2.pp617-624

Abstract

This paper presents a MATLAB/Simulink model for a 9-level cascaded H-bridge multilevel inverter with mismatched DC voltage sources. The impact of mismatched DC voltage sources on the performance of the 9-level CHBMI is investigated. Due to the mismatched voltages among DC voltage sources, the output fundamental voltage is different from the input reference voltage. To address this problem, a switching-angle calculation technique that accounts for mismatched as well as varying DC voltage sources is demonstrated. The switching angles obtained using this technique is able to produce the desired output fundamental voltage for a wide range of input reference voltages. Since this switching-angle calculation technique does not require complex iterative computation, it has the potential for real-time implementation.
Co-Authors J. A. Soo J. H. Leong M. Aizuddin M. Faddle S. L. Ong S. Lee T. Sutikno W. V. Yong Y. C. Tan