Garuda - Garba Rujukan Digital

Pengembangan Deteksi Suhu dan Kelembaban Laboratorium Elektronika Dengan Menggunakan Metode Fuzzy Logic Bahrun Niam; Rony Darpono; Martselani Adias Sabara
CIRCUIT: Jurnal Ilmiah Pendidikan Teknik Elektro Vol 6, No 1 (2022)
Publisher : PTE FTK UIN Ar-Raniry

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22373/crc.v6i1.10498

The electronics laboratory is an important place to run the practical activities, especially among electronics students. It is important to protect laboratory equipment and components from the temperature and humidity factors. Whether, the temperature is too cold and the humidity is too high, it caused the corrosion of all electronic components. Thus, it also caused minor until severe damage of the components. Arduino is an open source electronics kit which specially designed to make easier for researcher to develop electronic devices regarding to various sensors and controllers. The laboratory room temperature detection system was carried out by using an Arduino device, which aims to determine the temperature conditions in the laboratory. The method used in this research is the fuzzy logic method. The software used is Arduiono and Matlab, while the hardware is power supply, D1 Mini microcontroller, DHT11 sensor and LCD. The results showed that the temperature data obtained from the DHT11 sensor will be displayed on the LCD. The temperature data obtained is 27 degrees Celsius – 29 degrees Celsius. The system is able to provide information when the temperature and humidity conditions are abnormal and the LED lights up according to room conditions.

APLIKASI NODEMCU ESP8266 DAN SENSOR SUHU UNTUK MONITORING SUHU PERMUKAAN PANEL SURYA MELALUI SMARTPHONE Riyani Prima Dewi; Uli Karyani; Rony Darpono
Jurnal Ilmiah Flash Vol 8 No 2 (2022)
Publisher : P3M- Politeknik Negeri Kupang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32511/flash.v8i2.954

Potensi energi surya menurut energi outlook Indonesia (OEI) tahun 2019 sebesar 207,8 Gwp. Potensi tersebut merupakan yang terbesar diantara jenis energi terbarukan lainnya. Panel surya adalah peralatan utama sistem pembangkit listrik tenaga surya. Panel surya berfungsi untuk mengkonversikan energi cahaya matahari menjadi energi listrik. Kinerja sebuah panel surya dapat diketahui dengan cara mengukur parameter keluarannya seperti tegangan, arus dan daya. Kinerja panel surya dipengaruhi oleh beberapa faktor, diantaranya intensitas iradiasi matahari dan temperature kerja panel surya. Semakin besar iradiasi matahari yang ditangkap oleh panel surya makan semakin besar daya listrik yang dibangkitkan. Sekitar 15%-20% energi matahari yang diserap panel surya diubah menjadi listrik, sementara sisanya menghasilkan panas yang menyebabkan naiknya temperature permukaan panel surya. Kenaikan temperature ini justru akan menurukan daya listrik yang dihasilkan. Melalui pnelitian ini suhu panel permukaan panel surya akan diukur oleh sensor suhu DS18B20 kemudian dikirimkan ke NodeMCU ESP8622 sehingga dapat ditampilkan melalui aplikasi bylink di smartphone. Monitoring ini adalah upaya awal sebelum melakukan control terhadap suhu permukaan panel surya. Dari 3 hari percobaan, diketahui bahwa sistem monitoring yang dibuat berhasil berjalan dengan baik. Sensor suhu dapat membaca suhu permukaan panel dan aplikasi dapat menampilkan hasil pembacaan sensor. Terdapat selisih pembacaan suhu antara alat dengan alat ukur suhu sebesar 1,5 °C.

RANCANG BANGUN SISTEM INFORMASI GEMPA MENGGUNAKAN RASPBERRY PI BERBASIS WEB Ulil Albab; Rony Darpono; Fahreza Moch Revikansyah
JURNAL ILMIAH SAINS TEKNOLOGI DAN INFORMASI Vol. 1 No. 1 (2023): Januari : Jurnal Ilmiah Sains Teknologi dan Informasi
Publisher : CV. ALIM'SPUBLISHING

Earthquake is one of the natural disasters that can occur without being used. Earthquakes originate from vibrations in the bowels of the earth that travel to the surface caused by fractures in the earth breaking and shifting violently. To prevent material and inmaterial losses, this research can be carried out by utilizing hardware technology in the form of Raspberry PI and Piezoelectric Sensors. Raspberry PI is a small single-board computer (SBC) used for electronics projects. Raspberry PI has 40 pins divided into two modes, namely BCM and BOARD. For making a Piezoelectric Sensor value reading program using the Python Programming Language. The results of reading the output of the Piezoelectric Sensor integrated with the Raspberry PI are in the form of a voltage value. The output of the voltage is sent to the Website Page in real time. The collection of output data can then be analyzed if there are indications of an earthquake. The trial form was carried out by dropping the weight of objects weighing 2 and 3 Kilograms with the drop points being 25 cm, 50 cm and 95 cm. The experiment was carried out 3 times based on weight and falling point. From the test results, the value of vibration on the piezoelectric sensor was obtained with the lowest value of 107787 and the highest 568785063. For the criteria for an earthquake or not, it is divided into 2 categories, namely weak or strong. If the vibration value is more than 880000 it is interpreted as a strong category otherwise if it is less than 880000 it is categorized as weak. The sensor reading results are then stored in the database and displayed on the Website Page.

PELATIHAN MIKROKONTROLLER UNTUK MENINGKATKAN KOMPETENSI SISWA SMK BHAKTI PRAJA ADIWERNA Bahrun Niam; Rony Darpono; Muchamad Sobri Sungkar
SWARNA: Jurnal Pengabdian Kepada Masyarakat Vol. 2 No. 8 (2023): SWARNA: Jurnal Pengabdian Kepada Masyarakat, Agustus 2023
Publisher : LPPM Sekolah Tinggi Ilmu Ekonomi 45 Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55681/swarna.v2i8.800

Pengabdian Kepada Masyarakat dalam bentuk pelatihan mikrokontroler yang dilaksanakan di SMK Bhakti Praja Adiwerna untuk meningkatkan pengetahuan dan ketrampilan siswa-siswa tentang mikrokontroler. Mikrokontroler yang digunakan adalah D1 mini dan menggunakan sensor DHT11 untuk mendeteksi suhu dan kelembaban ruangan. Tahap pertama dalam pelatihan ini yaitu siswa diberi materi terlebih dahulu kemudian mempraktekkan cara merakit dan memprogram mikrokontrolernya. Suhu yang terbaca oleh sensor sebesar 26.00 0 C dan kelembabannya 73.00 %. Peserta pelatihan merasa senang dan semangat dalam mengikut pelatihan karena bisa memanfaatkan teknologi mikrokontroler untuk kehidupan sehari-hari.

PELATIHAN MIKROKONTROLLER UNTUK MENINGKATKAN KOMPETENSI SISWA SMK BHAKTI PRAJA ADIWERNA Bahrun Niam; Rony Darpono; Muchamad Sobri Sungkar
SWARNA: Jurnal Pengabdian Kepada Masyarakat Vol. 2 No. 8 (2023): SWARNA: Jurnal Pengabdian Kepada Masyarakat, Agustus 2023
Publisher : LPPM Sekolah Tinggi Ilmu Ekonomi 45 Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55681/swarna.v2i8.800

Pengabdian Kepada Masyarakat dalam bentuk pelatihan mikrokontroler yang dilaksanakan di SMK Bhakti Praja Adiwerna untuk meningkatkan pengetahuan dan ketrampilan siswa-siswa tentang mikrokontroler. Mikrokontroler yang digunakan adalah D1 mini dan menggunakan sensor DHT11 untuk mendeteksi suhu dan kelembaban ruangan. Tahap pertama dalam pelatihan ini yaitu siswa diberi materi terlebih dahulu kemudian mempraktekkan cara merakit dan memprogram mikrokontrolernya. Suhu yang terbaca oleh sensor sebesar 26.00 0 C dan kelembabannya 73.00 %. Peserta pelatihan merasa senang dan semangat dalam mengikut pelatihan karena bisa memanfaatkan teknologi mikrokontroler untuk kehidupan sehari-hari.

Peningkatan Pengetahuan Pembuatan Rangkaian Elektronika Menggunakan Proteus Di SMKN 3 Kota Tegal Ulil Albab; Qirom Qirom; Dany Sucipto; Rony Darpono; Bahrun Niam
Jurnal Surya Masyarakat Vol 8, No 1 (2025): November 2025
Publisher : Universitas Muhammadiyah Semarang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26714/jsm.8.1.2025.32-42

This community service activity was initiated in response to the limited ability of students at SMKN 3 Kota Tegal to design and analyze electronic circuits, due to inadequate access to industry-standard simulation software. The purpose of this program was to enhance students’ knowledge and skills through training in electronic circuit development using Proteus software. The implementation method consisted of preparation, training sessions, hands-on practice, and ongoing monitoring and evaluation. Participants included eleventh-grade students from the Electronics Engineering Department and accompanying teachers, who engaged in activities ranging from component introduction, circuit simulation, PCB design, to practical PCB fabrication using CNC machines. Evaluation results indicated a significant improvement in students’ understanding and technical capabilities, evidenced by an increase in average test scores from 75 to 93, and a 133 percent rise in the number of students achieving top score ranges. Furthermore, a shift was observed in teaching methods, from conventional whiteboard instruction to digitally integrated simulations. In conclusion, the Proteus-based training effectively enhanced students’ technical competencies, bridged the gap between theoretical concepts and practical applications, and better prepared vocational graduates to meet the demands of a technology-driven industrial environment..

Peningkatan Pengetahuan Pembuatan Rangkaian Elektronika Menggunakan Proteus Di SMKN 3 Kota Tegal Ulil Albab; Qirom Qirom; Dany Sucipto; Rony Darpono; Bahrun Niam
Jurnal Surya Masyarakat Vol 8, No 1 (2025): November 2025
Publisher : Universitas Muhammadiyah Semarang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26714/jsm.8.1.2025.32-42

This community service activity was initiated in response to the limited ability of students at SMKN 3 Kota Tegal to design and analyze electronic circuits, due to inadequate access to industry-standard simulation software. The purpose of this program was to enhance students’ knowledge and skills through training in electronic circuit development using Proteus software. The implementation method consisted of preparation, training sessions, hands-on practice, and ongoing monitoring and evaluation. Participants included eleventh-grade students from the Electronics Engineering Department and accompanying teachers, who engaged in activities ranging from component introduction, circuit simulation, PCB design, to practical PCB fabrication using CNC machines. Evaluation results indicated a significant improvement in students’ understanding and technical capabilities, evidenced by an increase in average test scores from 75 to 93, and a 133 percent rise in the number of students achieving top score ranges. Furthermore, a shift was observed in teaching methods, from conventional whiteboard instruction to digitally integrated simulations. In conclusion, the Proteus-based training effectively enhanced students’ technical competencies, bridged the gap between theoretical concepts and practical applications, and better prepared vocational graduates to meet the demands of a technology-driven industrial environment..

Title

Found 7 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 7 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 7 Documents
Search