BOYBUL BOYBUL
Unknown Affiliation

Published : 23 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 23 Documents
Search

PENGARUH PARAMETER PROSES ELEKTRODEPOSISI TERHADAP PENENTUAN BERAT ISOTOP 235U DALAM PEB U3Si2/Al PASCA IRADIASI Yanlinastuti Yanlinastuti; Boybul Boybul; Aslina Br. Ginting; Dian Anggraini
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 2 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.2.3093

Abstract

Electrodeposition process for determination of 235U isotope is affected by current, contact time, feed volume and type of buffer solution. The aim of this research is to obtain optimum parameter of electrodeposition process for 235U determination in U3Si2/Al irradiated fuel plate. Electrodeposition process is done by some variation of parameters, that are the current 1; 1.2; and 1.4 ampere with variation of time 1; 1.5; 2.0; 2.5 and 3.0 hours. The standard solution volume of 20% U3O8 are 100; 300; 500; 700 µL with variation of electrolyte buffer solution NH4Cl, NH4OAc, NH4HSO4 dan (NH4)2SO4. The result of electrodeposition process showed that optimum condition electrodeposition process for 235U isotope was obtained currents 1.2 ampere with process time for 2 hours, and 300 µL volume feed with electrolyte buffer NH4HSO4 in pH 3,5. The results of the electrodeposition process was obtained 2.314 µg deposition of the isotope 235U with recovery of 99.91%. The condition optimum parameter above was used for electrodeposition process in determination of 235U isotope which contained in U3Si2/Al irradiated fuel element. The spectrometer alpha analysis was obtained weight of 235U isotope as 0.403 µg with recovery of 91.80%. The conclusion of this research, the electrodeposition methods is good enough to be used for determining 235U isotope in U3Si2/Al irradiated fuel plate.
PENGARUH TEMPERATUR DAN IRADIASI TERHADAP INTERDIFUSI PARTIKEL BAHAN BAKAR JENIS U−7Mo/Al Maman Kartaman Ajiriyanto; Aslina Br. Ginting; Supardjo; Boybul Boybul
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 1 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.1.2740

Abstract

U−7Mo/Al alloy had great potential as research reactor fuel, but it had several disadvantages, such as, it can form a interaction layer at the interface during the process of fabrication and irradiation in a reactor. The research objective was determining the interaction layer that was caused by interdiffusion or diffusion couple of U−7Mo with AlMg2 alloy which was annealed at 500 °C and 550 °C for 24 hours. The observation of microstructure used a Scanning Electron Microscope (SEM) on diffusion couple sample which was heated at temperature of 500 °C had not seen the layer interaction or the formation of a new phase between particles of U−Mo and Al matrix, but heating treatment at 550 °C indicated that U−7Mo alloy had been interdiffusion with AlMg2 plate produced (U,Mo) Alx compound on the interfaces. It was evidenced by interdiffusion reaction analysis used DTA that showed that U−7Mo / Al alloy at 500 °C had good heat compatibility, but at temperatures upper than 550 °C it had been phase changed from a + d to a + g phase. The heating in DTA furnace up to 679.14 °C produced U(Al,Mo)x meta stable phase and then interdiffusion process with uranium molten formed layer interaction that formed UAlx compound agglomerates (UAl4, UAl3 and UAl2). Agglomerates was formed from the heating process which was similar to agglomerates that caused by irradiation. U−7Mo / Al Fuel alloy that had 58% burn up had been interdiffusion between U−7Mo with Al matrix produced U(Al,Mo)x metastable phase that turned into (U, Mo) Al7 layer, UMo2Al20 precipitates, (UMo)Al3−Al and formed a boundary or UAlx (UAl4, UAl3 and UAl2) agglomerates. The results of microstructure analysis used SEM and interdiffusion reactions used DTA was supported by the analysis of micro hardness used Vickers Hardness. The results of hardness analysis that was done to AlMg cladding and U−7Mo alloy (before and after heating) and diffusion couple of U−7Mo / Al samples with AlMg2 plate after heating at 550 °C were respectively 64.62 and 340.45 HV (before heating) and 52.34; 303.16 and 497.34 HV (after heating). Diffusion couple U−7Mo/Al with AlMg2 plate samples had the highest hardness value. This hardness difference showed that the interdiffusion test used diffusion couple produced a new compound (U, Mo) Alx in interface zone that had different character, but the formation of interaction layer is not expected in the fuel U−Mo / Al dispersion because micro hardness and density of (U, Mo) Alx compound’s layer was lower than the average density of U−7Mo/ Al alloy.
PENGARUH UNSUR Zr TERHADAP PERUBAHAN SIFAT TERMAL BAHAN BAKAR DISPERSI U-7Mo-xZr/Al Supardjo; Agoeng Kadarjono; Boybul Boybul; Aslina Br. Ginting
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 22 No. 1 (2016): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2016.22.1.2741

Abstract

Thermal properties data of nuclear fuel is required as input data to predict material properties change phenomenon during the fabrication process and irradiated in a nuclear reactor. Study the influence of Zr element in the U-7Mo-xZr/Al (x = 1%, 2% and 3%) fuel dispersion to changes in the thermal properties at various temperatures have been stiffened. Thermal analysis includes determining the melting temperature, enthalpy, and phase changes made using Differential Thermal Analysis (DTA) in the temperature range between 30 °C up to 1400 °C, while the heat capacity of U-7Mo-xZr alloy and U-7Mo-xZr/Al dispersion fuel using Differential Scanning Calorimeter (DSC) at room temperature up to 450 °C. Thermal analyst data DTA shows that Zr levels of all three compositions showed a similar phenomenon. At temperatures between 565.60 °C – 584.98 °C change becomes α + δ to α + γ phase and at 649.22 °C – 650.13 °C happen smelting Al matrix Occur followed by a reaction between Al matrix with U-7Mo-xZr on 670.38 °C – 673.38 °C form U (Al, Mo)x Zr. Furthermore a phase change α + β becomes β + γ Occurs at temperatures 762.08 °C – 776.33 °C and diffusion between the matrix by U-7Mo-xZr/Al on 853.55 °C – 875.20 °C. Every phenomenon that Occurs, entalphy posed a relative stable. Consolidation of uranium Occur in 1052.42 °C – 1104.99 °C and decomposition reaction of U (Al, Mo)x and U (Al, Zr)x becomes (UAl4, UAl3, UAl2), U-Mo, and UZr on 1328,34 °C - 1332,06 °C , The existence of Zr in U-Mo alloy increases the heat capacity of the U-7Mo-xZr/Al, dispersion fuel and the higher heat capacity of Zr levels increased due to interactions between the atoms of Zr with Al matrix so that the heat absorbed by the fuel increase.