Helmi Fauzi Rahmatullah
Unknown Affiliation

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

OPTIMASI PARAMETER JARAK VARIASI PROBE ULTRASONIC TEST IMMERSION PADA CLADDING PEB Refa Artika Artika; Helmi Fauzi Rahmatullah
PIN Pengelolaan Instalasi Nuklir Vol 11, No 21 (2018): Oktober 2018
Publisher : PIN Pengelolaan Instalasi Nuklir

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (8349.758 KB)

Abstract

ABSTRAKoptimasi Jarak probe ultrasonic test immersion pada cladding PEB. Telah didapat parameter jarak optimum pada pengujian kondisi permukaan kelongsong PEB menggunakan beberapa variasi probe ultrasonic test immersion. Penggunan alat uji ultrasonik khususnya pada kegiatan PIE (Post irradiation examination) merupakan salah satu metode pengujian pada tahap uji tak merusak bahan bakar nuklir yang ada di Instalasi Radiometalurgi PTBBN-BATAN.  Metode yang dilakukan yaitu membandingkan data sinyal keluaran %FSH (Full Screen High) pada variasi jarak tertentu (28 – 42 mm) pada probe IK-5-6, IK-5-10, dan IW-10-6 menggunakan sampel kelongsong PEB dengan kecepatan 6400 m/s. Hasil yang diperoleh pada masing-masing probe tersebut mempunyai jarak optimum 32 mm, 38 mm, dan 32 mm terhadap sampel dengan %FSH tertinggi pada probe IK-5-6. Sehingga optimasi parameter jarak variasi probe terbaik pada kelongsong PEB berjalan normal menghasilkan bahwa probe IK-5-6 merupakan probe terbaik dalam mengintrepetasikan kondisi permukaan kelongsong PEB jika terdapat cacat/anomali  Kata kunci: PIE, ultrasonic testing, probe, jarak optimum, kelongsong PEB ABSTRACTOPTIMIZATION OF DISTANCE OF ULTRASONIC TEST IMMERSION PROBE CLADDING PEB.The optimum distance parameters obtained in testing the surface condition of the PEB cladding using a variety of ultrasonic test immersion probes. The use of ultrasonic testing equipment, especially in PIE activities (Post irradiation examination), is one of the testing methods at the test stage which does not damage nuclear fuel in Radiotherapy Metallurgical Instalation of PTBBN-BATAN. The method used is to compare %FSH (Full Screen High) output signal data at certain distance variations (28 – 42 mm) on IK-56, IK-5-10, and IW-10-6 probes using PEB cladding samples with 6400 m/s velocity. The results obtained are that each of these probes has an optimum distance of 32 mm, 38 mm, and 32 mm against the sample with highest %FSH on the IK-5-6 probe. So that the optimization of the parametersof the variation of probes on the PEB cladding is normal and results in the probes IK-5-6 being the best probe in interpreting the surface conditions of the PEB cladding if there are defects/anomalies. Key words: PIE, ultrasonic testing, probe, optimum distance, PEB cladding
ANALISIS CACAT BLISTER PADA KELONGSONG BAHAN BAKAR U3Si2/Al MENGGUNAKAN ULTRASONIC TEST Muhammad Fauzi; Roziq Himawan; Helmi Fauzi Rahmatullah; Setia Permana; Antonio Gogo
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 3 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.3.3629

Abstract

Fuel integrity is one of safety considerations during nuclear reactor operation. Any defect resulted after reactor operation should be avoided. Thus, in nuclear fuel development, post-irradiation examination is necessary to be performed to ensure fuel integrity. Non-destructive test using ultrasonic method is one of alternative methods to perform post-irradiation examination. The objective of this analysis is to detect blister defect in cladding of plate type nuclear fuel. In post irradiation examination (PIE) using ultrasonic method, the operation parameters are necessary to determine. In this experiment, this analysis method was conducted on U3Si2/Al fuel element cladding consisting of blister defect. Ultrasonic tests were done using two techniques, i. e. pulse-echo and through transmission techniques. The results were presented in A-scan display. The results show that the longitudinal wave speed in water used in the testing is 1545 m/s. The optimal distance between the probe and the specimen when using pulse-echo technique is 20 mm. The optimal distance between the two probes when using through transmission technique is 40 mm. Tests at blister area using pulse-echo technique caused output signal to decrease by 19 %FSH, while through transmission technique caused output signal to decrease by 80 %FSH. According to the results it can be concluded that ultrasonic test is effective to detect a blister defect in plate type nuclear fuel, and through transmission technique exhibited a clearer difference between normal area and blister area in fuel cladding when compared to pulse-echo technique.
PENGUKURAN BERAT RADIONUKLIDA 137Cs DALAM LARUTAN PELAT ELEMEN BAKAR U3Si2/Al DENSITAS 4,8 gU/cm3 PASCA IRADIASI DENGAN METODE KOLOM KROMATOGRAFI Boybul; Yanlinastuti; Erlina Noerpitasari; Juan Carlos Sihotang; Helmi Fauzi Rahmatullah; Arif Nugroho; Mohammad Sukron Fajrin Husein; Rohmad Sigit; Aslina Br Ginting; Susilo WIdodo
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 30 No. 1 (2024): Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/urania.2024.8678

Abstract

The burn up value of the fuel is one of the parameters that must be known in the post-irradiation examination. The determination of burn up aims to determine the performance of U3Si2/Al fuel after being used in the reactor. One of the isotops that can be used as an indicator of burn up is 137Cs because it has a long half-life (T1/2) of 30.17 years with a fission yield of 6.26%. Therefore, in this study, a separation was carried out to determine the amount of 137Cs in the U3Si2/Al fuel solution post irradiation using the cation exchange column method using zeolit from Lampung along with its recovery rate. The solution of irradiated U3Si2/Al fuel from Top (T), Middle (M), and Bottom (B) position, was each pipetted in a duplicate manner (duplo) in an amount of 50 µL and added with 2 mL of 0.1 M HNO3. The solutions were then measured activity using a gamma spectrometer to obtain the initial weight of 137Cs radionuclide. The solution was then inserted into a chromatography column containing 700 mg of zeolit Lampung and allowed to flow under vacuum condition. The separation results showed that 137Cs was bound to the zeolit in the form of 137Cs-zeolit solid phase, while other isotops remained in the liquid phase. The solid 137Cs-zeolit and 137Cs in the supernatant were then measured with a gamma spectrometer to determine the weight of 137Cs bound to the zeolit. The measurement results showed that the average initial weight of 137Cs (before separation) were 7.49 × 10-3 µg/gFEP and dan 6.97 × 10-3 µg/gFEP for T1 and T2 from top section, 10.50 × 10-3 µg/gFEP for M1 from Middle section, and dan 8.43 × 10-3 µg/gFEP and 8.76 × 10-3 µg/gFEP for B1 and B2 from Bottom section, respectively. After separation, the average weight of 137Cs were 7.43 × 10-3 µg/gFEP and 6.82 × 10-3 µg/gFEP for T1 and T2, 10.10 × 10-3 µg/gFEP for M1, and 8.32 × 10-3 µg/gFEP and 8.41 × 10-3 µg/gFEP for B1 and B2, respectively. From the weight of 137Cs before and after separation, the average separation recovery with the cation exchange chromatography column method using zeolit was obtained at 97.748%. This recovery value indicates that zeolit Lampung is highly selective for absorbing 137Cs in the solution of irradiated U3Si2/Al fuel.
OPTIMASI PEMISAHAN SESIUM DI DALAM PELAT ELEMEN BAKAR TIPE U3Si2/Al PASCA IRADIASI MENGGUNAKAN METODE PENGENDAPAN KLOROPLATINAT Arif Nugroho; Komar Sutriah; Sri Mulijani; Triyono Basuki; Ahmad Ade Rofiqi; Noviarty; Helmi Fauzi Rahmatullah; Ganisa Kurniati Suryaman; Guswardani
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 30 No. 1 (2024): Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/urania.2024.8679

Abstract

Several methods for separating fission product ¹³⁷Cs from uranium isotopes (²³⁸U, ²³⁵U, ²³⁶U, and ²³⁴U) in U₃Si₂/Al fuel have been widely developed. Optimization and separation were performed using the chloroplatinate precipitation to establish a new cesium (Cs) separation method. The method developed in this research offers the potential to achieve higher-purity cesium precipitates. This study aims to develop a method of separating the ¹³⁷Cs isotope from U₃Si₂/Al fuel element plates (PEB) using chloroplatinate reagents. The procedure involves dissolving the pre-irradiation U₃Si₂/Al PEB and adding several elements such as Sm, Sr, Cs, and Nd to represent the composition of pre-irradiation PEB, simulating its original condition. The cesium precipitation process in the supernatant solution was carried out by adding HCl and NaOH to separate impurities from cesium. The precipitation was conducted by adding H₂PtCl₆ to precipitate and isolate cesium from other elements. The precipitation process was optimized by varying the temperature and precipitation time. The optimum precipitation conditions were achieved at a temperature of -3°C and a time of 10 minutes, resulting in a Cs2PtCl6 precipitate weighing 0.3361 g. XRD and SEM analyses were used to complement and verify the cesium separation results using the chloroplatinate precipitation method, showing a uniform distribution of all elements. The purity of the Cs2PtCl6 precipitate obtained was 100%, with a diffractogram pattern identical to the reference.