Petrus Zacharias
PRFN - BATAN

Published : 5 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 5 Documents
Search

ANALISIS KESELAMATAN RADIASI PADA KOLAM IRADIATOR “IZOTOP” Petrus Zacharias; Abdul Jami
PRIMA - Aplikasi dan Rekayasa dalam Bidang Iptek Nuklir Vol 11, No 2 (2014): November 2014
Publisher : BATAN

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (154.286 KB)

Abstract

ABSTRAK ANALISIS  KESELAMATAN  RADIASI  PADA KOLAM IRADIATOR  “IZOTOP”. Iradiator “Izotop” buatan Institute of Isotope Co.Ltd. Hungaria merupakan iradiator gamma panorama katagori IV yang dapat beroperasi secara kontinyu dan   batch. Kapasitas maksimum sumber gamma pada iradiator ini adalah 2 MCi. Kolam penyimpan sumber berukuran lebar 2,8 m, panjang 3,6 m, dan  kedalaman 6 m berisikan air bebas mineral. Rak sumber berukuran panjang 3 m dan tinggi 1 m. Jarak antara permukaan air kolam dan rak sumber menentukan fungsi air sebagai perisai radiasi. Konsep jarak ini digunakan untuk mengevaluasi   keselamatan radiasi kolam Iradiator “Izotop”. Pasal 8 dari SSG-8 IAEA digunakan sebagai referensi untuk analisis ini. Penentuan faktor  build–up air menggunakan Persamaan Taylor. Perhitungan laju dosis di atas kolam dilakukan untuk masing-masing tingkat permukaan  air, yaitu pada tingkat air normal, dan untuk setiap  0,3 m penurunan permukaan air  hingga penurunan sampai 1,5 m. Pada tingkat air normal sampai penurunan permukaan air 1,2 m, hasil perhitungan menunjukkan laju dosis sangat aman. Keadaan  laju dosis radiasi mencapai tingkat tidak aman ketika penurunan tingkat air  lebih dari 1,2 m. Hasil evaluasi ini memberikan gambaran bahwa desain kolam Iradiator “Izotop” dapat memenuhi    rekomendasi  IAEA.  Berdasarkan  rekomendasi ini,  pada  operasi  normal  iradiator gamma kategori IV, proses make – up air harus dilakukan ketika permukaan air berada di batas normal bawah, sehingga kejadian tidak aman tidak terjadi. Kata kunci : Iradiator “Izotop”, kolam iradiator, laju dosis, keselamatan radiasi  ABSTRACT RADIATION  SAFETY ANALYSIS  ON THE “IZOTOP” IRRADIATOR  POOL. “Izotop” Irradiator manufactured by Institute of Isotope Co. ltd. Hungary is a category IV panoramic gamma irradiators which can operate in both continuous and batch modes. The maximum gamma source capacity of the irradiator is 2 MCi. The dimension of the source storage pool containing demineralized water is about 6 m in deep, 2.8 m in wide and 3.6 m in length. The source rack is about 3 m in length and 1 m in height.  The distance between the surface of the pool water and the source rack defines the water as radiation shielding. The distance is used to evaluate the radiation safety of the “Izotop” Irradiator pool. Article 8 of the IAEA SSG-8 is used as reference for this analysis. Determination of water build-up factor uses Taylor's formula.  The calculation of the dose rate at the border of the pool was done for each of the water level, ie.  at the normal water level, and for each 0.3 m drop in water level decreasing until 1.5 m. At normal water levels, and up to 1.2 m of drop in water level, the result shows a very safe dose rate levels. The radiation dose rate reaches unsafe level  when the  water  level decreases more than  1.2  m.  The  results  of  this evaluation shows that “Izotop” Irradiators pool design can meet IAEA recommendations. Based on these recommendations, in normal operation of gamma irradiators category IV, the make - up of water shall be operated when the water level is in the normal low water level, so that the unsafe incidence will not happen. Keywords: “Izotop” Irradiators, irradiator pool, dose rate, radiation safety.
UJI TANPA RUSAK PADA SAMBUNGAN LASAN LINER KOLAM IRADIATOR GAMMA Petrus Zacharias; Harno Garnito; Tri Wahono
PRIMA - Aplikasi dan Rekayasa dalam Bidang Iptek Nuklir Vol 13, No 2 (2016): November 2016
Publisher : BATAN

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (12143.139 KB)

Abstract

ABSTRAKUJI TANPA RUSAK PADA SAMBUNGAN LASAN LINER KOLAM IRADIATOR GAMMA. Untuk menjaga kualitas produk agar sesuai dengan standar yang ditetapkan, maka perlu dilakukan inspeksi atau pemeriksaan terhadap produk tersebut. Untuk mengetahui ada atau tidaknya cacat pada produk sebelum dilakukan proses berikutnya, ataupun sebelum produk dipasarkan maka biasa dilakukan pemeriksaan dengan metode uji tanpa rusak atau Non Destructive Testing (NDT), yaitu pengujian bahan dengan tidak merusak bahan yang diuji. Untuk memeriksa ada tidaknya cacat pada sambungan las dalam liner irradiator, telah dilakukan uji radiografi dan liquid penetrant. Hasil uji menunjukkan adanya beberapa cacat seperti undercut pada base metal dan porosity. Temuan adanya cacat ini telah ditindaklanjuti dengan perbaikan las ulang sebagaimana yang direkomendasikan. Hasil ulang uji radiografi dan penetrant pasca perbaikan menunjukkan bahwa cacat telah berhasil dihilangkan. Dengan demikian, lasan pada liner iradiator dapat diterima.Kata kunci : Uji Tanpa Rusak, liner kolam iradiator, cacat las.  ABSTRACTA NON DESTRUCTIVE TESTING ON GAMMA IRADIATOR POOL LINER WELD JOINTS. To keep the quality of the products to conform to established standards, there should be an inspection or examination of the products. To determine whether there is any defect in the products prior to the next process or before the products to be launched to the market, it is usually the product to be inspected by Non Destructive Testing method (NDT), which is testing the material without spoiling the material being tested. To inspect the absence of defects in the welded joints in irradiator pool liner, the radiographic examination and liquid penetrant have been conducted. The examination obtained some undercuts and porosities defects in welded joints. All of welded defects have been repaired by rewelding according to the recommendation. And all repaired weld in joints have been checked by repeating radiography and liquid penetrant examination and by repeating the original inspection procedure.Key words: Non Destructive Testing, iradiator pool liner, weld defects
DESAIN PERANGKAT KAIT OVERHEAD TRAVELLING CRANE DENGAN KAPASITAS ANGKAT 25 TON PADA PABRIK ELEMEN BAKAR NUKLIR Syamsurijal Ramdja; Petrus Zacharias
PRIMA - Aplikasi dan Rekayasa dalam Bidang Iptek Nuklir Vol 12, No 1 (2015): Juni 2015
Publisher : BATAN

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1117.137 KB)

Abstract

ABSTRAKDESAIN PERANGAKT KAITOVERHEAD TRAVELLING CRANE DENGAN KAPASITAS ANGKAT 25 TON PADA PABRIK ELEMEN BAKAR NUKLIR. Telah dilakukan desain perangkat Kait Overhead Traveling Crane dengan kapasitas angkat 25 ton yang digunakan  pada pabrik elemen bakar nuklir. Kait  digunakan untuk memegang  bahan/material yang akan diangkat atau dipindahkan. Perancangan perangkat kait dilakukan dengan memperhatikan keamanan suatu data ukuran dan dimensi yang dipakai serta beban operasi apakah masih aman digunakan dalam kegiatan pengoperasian. Hal ini dilakukan untuk mengetahui apakah perangkat kait masih berada pada batas dimensi dan kekuatan bahan yang diizinkan. Desain ini berdasarkan pada standar ASME B30.2 yang berlaku dan dengan  faktor keamanan yang konservatif, terhadap : kait, bantalan aksial, pemikul kait dan sackle. Setelah dilakukan desain dan perhitungan, didapatkan bahwa perangkat kait yang terdiri dari kait, bantalan aksial, pemikul kait dan shackle dalam keadaan aman.Kata kunci : kait, kekuatan bahan, crane, schakle, bantalan ABSTRACTDESIGN OF HOOKS OF THE OVERHEAD TRAVELLING CRANE 25 TONS CAPACITY USED IN NUCLEAR FUEL ELEMENTS PLANT.  It has been design a hook overhead traveling crane with a lift capacity of 25 tons which is used in nuclear fuel elements plant. The hooks are used to hold the material to be removed or relocated. The design of hooks is conducted by considering to the safety factor of data and size dimensions to be used as well as its operational load whether still safe in its operating activities. This is done to determine whether the device is still in the material strength limit allowed. The design is based on the standards applicable of ASME B30.2 and with a conservative safety factors towards : hooks, axial bearings, latches and schakle bearers . After the design and calculations have been conducted, it was found that the hook consisting of hooks, axial bearings, bearer hook and shackle are in a safe condition.Keywords : hook, strength of materials, kran, schakle, bearings
PENENTUAN SPESIFIKASI TEKNIS KOMPONEN-KOMPONEN UTAMA PADA BAGIAN MEKANIK MASUK-KELUAR BOX CAR DARI RUANG IRADIASI PADA INSTALASI IRADIATOR GAMMA 200 KCi Ari Satmoko; Petrus Zacharias; Budi Santoso
PRIMA - Aplikasi dan Rekayasa dalam Bidang Iptek Nuklir Vol 11, No 2 (2014): November 2014
Publisher : BATAN

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1081.429 KB)

Abstract

ABSTRAKPENENTUAN SPESIFIKASI TEKNIS KOMPONEN-KOMPONEN UTAMA PADA BAGIAN MEKANIK MASUK-KELUAR  TOTE DARI RUANG  IRADIASI PADA INSTALASI  IRADIATOR GAMMA 200 KCi. Iradiator gamma 200 KCi dirancang untuk proses pengawetan bahan pangan menggunakan sumber radioaktif Cobalt-60. Desain iradiator mengacu pada jenis iradiator yang dikembangkan oleh Izotop Hungaria. Salah satu karakteristik dari iradiator jenis ini adalah pintu masuk dan keluar poduk melalui sebuah pintu tunggal. Ketika produk akan diiradiasi, produk tersebut disusun dalam tote-tote. Selanjutnya tote-tote ini dimasukkan ke dalam ruang iradiasi dengan diangkut oleh box car. Di dalam ruang iradiasi, tote-tote bergeser mendekati dan menjauhi sumber isotop Cobalt-60. Selesai iradiasi, tote kembali diangkut oleh box car melalui jalur yang sama. Proses masuk-keluar box car inilah yang menjadi bahasan dalam makalah ini. Pembahasan bertujuan  untuk  menentukan  spesifikasi  teknis  untuk  komponen-komponen  utama.  Kegiatan diawali dengan mempelajari geometri lintasan rantai. Selanjutnya persamaan gaya dikembangkan dan diselesaikan. Dengan diperolehnya gaya yang dibutuhkan untuk menarik rantai, beberapa spesifikasi komponen utama berhasil diidentifikasi seperti motor, rantai, sproket dan gearbox. Berdasarkan perhitungan daya motor minimum adalah 1 HP. Rantai telah diidentifikasi dengan spesifikasi nomor rantai 40. Sproket terdiri dari dua jenis. Jenis pertama adalah sproket yang dipasang langsung pada motor dengan jumlah gigi 40. Sedangkan jenis lainnya adalah sproket 12 gigi yang berjumlah 103 buah. Untuk gearbox, rasio penurunan kecepatan yang ditetapkan adalah 1:96.Kata kunci: iradiator, penentuan spesifikasi teknis, komponen mekanik, perhitungan ABSTRACTDETERMINATION OF TECHNICAL SPECIFICATIONS FOR MAIN COMPONENTS IN THE MECHANICAL  LOADING-UNLOADING  TOTE FROM IRADIATION  ROOM ON THE 200 KCi GAMMA IRRADIATOR. The Gamma irradiators 200 kci is designed for food preservation process. The irradiator uses radioactive Cobalt-60 sources. Its design refers to the type that is developed by Izotop Hungary. One of the characteristics of this type is that the entrance and the exit are through a single door. When the products to be irradiated, the products are prepared in totes. Furthermore, these totes, transported by a box car, go into the irradiation room. In the room, totes are moved closer to and away from Cobalt-60 isotope sources. After irradiation, these totes go out transported by the box car through the same pathway. In this paper, the process of box car going into and out from the irradiation room is discussed. The discussion aims to define the technical specifications for major components. It begins with studying the geometry of the track chain. Furthermore, force equations are developed and resolved. By obtaining the force required to pull the chain, some specifications of the major components were identified as motors, chain, sprocket and gearbox. Based on the calculation, the minimum motor power is 1 HP. Chain has been identified with the specification number 40. Chain sprocket consists of two types. The first type is a sprocket that is mounted directly on the motor with the number of teeth 40. The other type is a 12 teeth sprocket which amounted to 103 pieces. For gearboxes, the speed reduction ratio is set to 1:96.Keywords: iradiator, determining technical specifications, mechanical components, calculation
PERHITUNGAN SEBARAN OZON DARI CEROBONG IRADIATOR GAMMA PRFN Rissa Damayanti; Iwan Roswandi; Petrus Zacharias
PRIMA - Aplikasi dan Rekayasa dalam Bidang Iptek Nuklir Vol 12, No 2 (2015): November 2015
Publisher : BATAN

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2068.386 KB)

Abstract

ABSTRAKPERHITUNGAN SEBARAN OZON DARI CEROBONG IRADIATOR GAMMA PRFN, Analisis perhitungan meliputi estimasi seberapa banyak ozon yang tersebar di area sekitar instalasi iradiator gamma PRFN yang dihasilkan selama proses iradiasi berlangsung. Ozon yang terbentuk selama proses iradiasi akan disirkulasi oleh blower ozon dan dibuang ke udara bebas lewat cerobong buangan dengan sistem pertukaran udara ruangan iradiasi tipe basah yang membutuhkan minimal 20 kali pergantian udara per jam atau konsentrasi ozon di udara tidak melebihi nilai batas yang diizinkan yaitu 0,1 ppm. Pergerakan ozon di atmosfer / udara bebas terjadi dalam tiga dimensi secara horizontal maupun transversal, sesuai dengan arah angin (adveksi) maupun vertikal, ke lapisan atas atmosfer bumi. Untuk melakukan perhitungan tersebut dilakukan dengan menggunakan Model Dispersi Gauss. Data yang digunakan dalam melakukan pehitungan adalah kecepatan angin minimal pada ketinggian cerobong 11 meter sebesar 0.1 m/detik dan kecepatan angin maksimal sebesar 6 m/detik pada saat pagi, siang dan malam hari. Laju emisi ozon (Q) adalah 0.000707 gram/detik, dengan variasi jarak pemaparan menurut arah angin dari 1 meter hingga 6 meter (0.001 – 0.00 Km). Dari hasil perhitungan yang telah dilakukan diperoleh kondisi paparan ozon tertinggi, yaitu : pada kecepatan angin 0.1 m/s, kestabilan udara kelas A (sangat tidak stabil) pada pagi/siang dengan intensitas matahari kuat. Pada nilai-nilai paparan ozon tersebut pada jarak x ≤ 1 m, y = 0, z = 1,1.5,2,2.5,3,…17 m nilai konsentrasi paparan ozon > 0,1 ppm (lebih dari nilai batas yang diizinkan), namun kondisi pada lokasi dengan koordinat lain x ≥ 1 m, y = 0, z = 1,1.5,2,2.5,3,…17 m, dan x = 1,2,3,4,5,6 m, y 0.5,1,1.5,2,2.5,3 m, z = 0 nilai konsentrasi paparan ozon < 0,1 ppm (tidak lebih dari nilai batas yang diizinkan). Sehingga dapat dikatakan yang mempengaruhi besar dari konsentrasi paparan ozon ke lingkungan antara lain: kecepatan angin, kecepatan emisi gas buang, kecepatan linear gas buang dalam cerobong, percepatan gravitasi, kelas kestabilan udara, serta selisih antara temperatur gas buang dan temperatur udara lingkungan.Kata kunci: Iradiator Gamma, Sebaran Ozon, Cerobong Iradiator, Dispersi. ABSTRACTA CALCULATION OF OZONE DISTRIBUTION FROM THE CHIMNEY GAMMA IRRADIATOR PLANT OF PRFN. Calculation includes estimation of ozone scattered in the area around the installation of the PRFN gamma irradiator generated during irradiation process. Ozone which is formed during irradiator in operation will be circulated by the blower and discharged into the atmosphere through the exhaust chimney of the wet type air exchange system irradiation room that requires a minimum of 20 times the air changes per hour or the concentration of ozone in the air does not exceed the allowed limit is 0.1 ppm. The movement of ozone in the atmosphere occurs in three dimensions horizontally and transverse, in accordance with the direction of the wind (advection) or vertically, to the top layer of the earth's atmosphere. To perform these calculations the Gaussian Dispersion Model has been used. The data used in the calculation are the minimum wind speed at the height of the chimney 11 meters of 0.1 m / sec and a maximum wind speed of 6 m / sec during the morning, afternoon and evening. Ozone emission rate (Q) is 0.000707 grams / sec, with a variation of exposure downwind distance of 1 meter to 6 meters (0.001 - 00:00 Km). From the results of the calculations have been done obtained the highest ozone exposure conditions, ie: at a wind speed of 0.1 m / s, air stability classes A (very unstable) in the morning / afternoon with strong solar intensity. At the values of ozone exposure are at a distance x ≤ 1 m, y = 0, z = 1,1.5,2,2.5,3, ... 17 m value exposure to ozone concentrations> 0.1 ppm (over limit values allowed) , but the conditions at other locations with coordinates x ≥ 1 m, y = 0, z = 1,1.5,2,2.5,3, ... 17 m, and x = 1,2,3,4,5,6 m, y 0.5,1,1.5,2,2.5,3 m, z = 0 value exposure to ozone concentrations <0.1 ppm (no more than the permitted limit values). So it can be said that influence of the concentration of ozone exposure to the environment, among others: the wind speed, the speed of exhaust emissions, exhaust gas linear velocity in the chimney, the acceleration of gravity, air stability classes, as well as the difference between the temperature of the exhaust gas and ambient air temperature.Keywords : Gamma Irradiator, Distribution of Ozone, Chimney Irradiator, Dispersion