Article Per Year (5 Year)
p-Index From 2020 - 2025
0.23
P-Index
This Author published in this journals
All Journal Majalah Kedokteran Gigi Indonesia
Erwan Sugiatno
Department of Prosthodontics, Faculty of Dentistry, Universitas Gadjah Mada, Yogyakarta
Dentistry

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
The transversal strength comparison between polyethylene and glass fiber as an acrylic resin denture plate repair material Pramudya Aditama; Erwan Sugiatno; Sabdayana Sabdayana
Majalah Kedokteran Gigi Indonesia Vol 5, No 1 (2019): April
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (317.814 KB) | DOI: 10.22146/majkedgiind.17497

Abstract

Acrylic resin is the most commonly used denture base material. However, it has a shortage of being easily broken. One way to resolve this problem is by adding polyethylene (PE) or glass fibers. The purpose of this research is to compare the transversal strength of PE and glass fibers from denture plate acrylic resin repair material. The experiment involved 32 plates of heat cure acrylic with the dimensions of 65 mm x 10 mm x 2.5 mm. The speciments were prepared to create a 3 mm gap and 45° bevel. Subjects were divided into 2 groups, each group containing 16 plates. Group I was reinforced with PE fiber and Group II was reinforced with glass fiber. All plates were soaked in distillation water for one day at 37 °C. Plates were tested for transverse strength with universal testing machine and all data were analyzed with independent t-tes at 95% confidence level. Macro photo analysis was used to observed the bond failure on fiber and resin. The mean of transverse strength (MPa) denture plate acrylic resin repair material reinforced with PE fiber was (67.38 ± 4.31) MPa, while glass fiber was (93.61 ± 6.14) MPa. Independent t-tes showed that type of fiber had a significant effect (p<0.05). Thus, it is possible to conclude that addition of glass fibers in denture plate acrylic resin repair material increased the transverse strength and made it stronger than those added with PE fibers.
The effect of fiber type and position on the transverse strength of an fiber reinforced composite (FRC) bridge Pramudya Aditama; Erwan Sugiatno; Murti Indrastuti
Majalah Kedokteran Gigi Indonesia Vol 6, No 3 (2020): December
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/majkedgiind.44616

Abstract

Fixed bridge made of porcelain fused to metal (PFM) is one of the widely used dentures. However, this type of denture is easily broken and cracked. As an alternative, a fixed bridge made of fiber-reinforced composite (FRC) is produced with more benefits since it is more efficient in terms of time and cost. The purpose of this research is to find out the effect of type and fiber position on the transverse strength of an FRC bridge. The experimentinvolved 35 rod of FRC with the dimensions of 25x2x2 mm3. Subjects were divided into seven groups, each of which containing five subjects. Group I, II, III was reinforced with glass fiber on compression side, neutral side, and tension side. Group IV, V, VI were reinforced with polyethylene (PE) fiber on compression side, neutral side, and tension side. Group VII was not reinforced with any fiber. Rods were tested for transverse strength with universaltesting machine and all data were analyzed with two way ANOVA at 95% confidence level. The results showed that type and position of fiber had a significant effect (p<0.05), while the interaction between type and position of fiber had no significant effect (p>0.05). Least significance different post hoc test showed significant difference (p<0.05) for all groups, except between compression and no fiber. The conclusion of this research was that addition of glass fibers on tension side in bridge FRC increased the transverse strength to be higher than that with PE fibers. Fiber placement on tension side might improve the transverse strength than that of the other side.
Co-Authors Murti Indrastuti Pramudya Aditama Sabdayana Sabdayana