Claim Missing Document
Check
Articles

Found 3 Documents
Search

TINJAUAN BEBAN LENTUR DAN REMBESAN AIR PADA GENTENG DENGAN BAHAN TAMBAH LIMBAH SERBUK KACA Cintia Pratiwi; Kusno Adi Sambowo; Supardi Supardi
Matriks Teknik Sipil Vol 2, No 1 (2014): Maret 2014
Publisher : Program Studi Teknik Sipil FT UNS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/mateksi.v2i1.37471

Abstract

Glass powder has considerable volume in wastes and has not thoroughly been utilized. Therefore, the waste glass powders can maximally be exploitedby utilizing them as the aggregates of roof tile manufacture. The objective of this research is to investigate the effect of waste glass powders asthe aggregates of the roof tile manufacture on the flexural load and water absorption. The test specimens consisted of four main groups based on thepercentage of waste glass powders, namely: 0%, 5%, 10%, and 15% of the dry weight of clay. Each group consisted of 10 test specimens, andtherefore the total number of the specimens was 40. Flexural load was tested by using bending testing machine, and the water absorption was testedby using the pvc pipe with the diameter of ¾'' and the length of 6 cm. The result of the specimen testing shows that the values of the averageflexural load with percentage of the waste glass powder supplementation of 0%, 5%, 10%, and 15% were 50 kg, 62 kg, 72 kg, and 63 kg respectively.the increasing supplementation of the waste glass powder was increasing the value of flexural load but after passing the optimum limitflexural load will decrease. The result of the regression analysis shows that the optimum flexural load was obtained in the waste glass powdersupplementation of 9.817% with the value of flexural load of 69.469 kg. All of the roof tiles with or without the waste glass powder supplementationwere included in the roof tile classification of Class IV of the standards of PUBI 1982. In addition, the result of the water absorption testingshows that the increasing supplementation of the waste glass powder was reducing the percentage of the water absorption. Therefore, the supplementationof the waste glass powder was improving the quality of the roof tiles.
KAJIAN KUAT LENTUR BALOK BETON BERTULANGAN BAMBU PETUNG TAKIKAN TIPE V DENGAN JARAK 2 CM DAN 3 CM Fitra Ameldi; Agus Setiya Budi; Supardi Supardi
Matriks Teknik Sipil Vol 2, No 2 (2014): Juni 2014
Publisher : Program Studi Teknik Sipil FT UNS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (390.436 KB) | DOI: 10.20961/mateksi.v2i2.37451

Abstract

In the construction industry, concrete reinforced steel is a construction material that is commonly used in building structures, where the compressivestrength of concrete and the tensile strength of steel is a combination that complement each other. However, using steel as reinforcement still get someconstraints amongst the price more higher and that is a product of the mining which unrenewable and someday will runs out. To resolve theseconstraint, as an alternative solution to replace steel reinforcement, then utilized bamboo, where bamboo is a natural product which renewable,easily to get, inexpensive, and have a high tensile strength. from that idea, This research was conducted to determine the yield strength of bamboopetung used for analysis and the flexural capacity of the beam Reinforced bamboo petung, by making beam specimen a total of 12 pieces withdimention of 11 cm x 15 cm x 170 cm. Three of the first beam specimen planted reinforcement bamboo petung notches type V with distance 2 cmand 3 cm for the next beam specimen, The next three beam specimens planted reinforcement steel ø 8 mm and three beam specimen unreinforcedfor comparison. Testing was conducted in Structures laboratory, FT UNS, at the age of concrete 28 days with giving two concentrated loads pointsat a distance of 1/3 span beam from toehold. Based on the analysis and test results can be concluded, yield strength of bamboo petung obtained at223.893 N/mm2 or a tensile strength on nodia, because the tensile strength on nodia at least half of the tensile strength in internodia. For theflexural capacity of test results, flexural capacity of beam reinforced bamboo petung notches with distance 2 cm greater 4,04% than beam reinforcedsteel ø 8 mm, while for beam reinforced bamboo petung notches 3 cm obtained 2.424% larger than the beam reinforced steel ø 8 mm. From the12 pieces specimen beams, average collapse occurs in the area 1/3 middle span beams and can said to be as the collapse of flexible. With thisexperimental test results of the beams reinforcement bamboo petung notches type V with distance 2 cm and 3 cm sufficient potential as areplacement for steel reinforcement on a simple building.
KUAT LEKAT TULANGAN BAMBU PETUNG TAKIKAN TIPE V DENGAN JARAK TAKIKAN 2 CM DAN 3 CM Mustamir Saifuddin; Agus Setiya Budi; Supardi Supardi
Matriks Teknik Sipil Vol 2, No 2 (2014): Juni 2014
Publisher : Program Studi Teknik Sipil FT UNS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/mateksi.v2i2.37441

Abstract

Study of bond stength petung bamboo reinforcement type V notch with distance of 2 cm and 3 cm in normal concrete. This study used an experimental method with a total of 15 pieces of the test specimen . Specimens used are concrete cylinders with a diameter of 15 cm and 30 cm high . As reinforcement using bamboo reinforcement petung without nodia with the notch distance of 2 cm and 3 cm . Bamboo petung bernodia with the notch distance of 2 cm and 3 cm . Each specimen 3 pieces with type V notch , the notch width 0.8 cm and 0.5 cm depth of the notch . Bamboo reinforcement dimensions length 70 cm, width 2 cm and 0.52 cm thick . As a comparison using steel reinforcement with a diameter of 0.8 cm and a length of 70 cm specimen 3 pieces . Quality concrete with f'c = 17.5 planned MPa . Adhesion test was conducted at 28 days by using a Universal Testing Machine ( UTM ) .