Article Per Year (5 Year)
p-Index From 2021 - 2026
0.408
P-Index
This Author published in this journals
All Journal Jurnal Ilmiah Teknik Mesin Poros
Sobron Y. Lubis
Program Studi Teknik Mesin UNTAR
Mechanical Engineering

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
VARIASI KECEPATAN PEMOTONGAN PROSES PEMBUBUTAN BAJA AISI 4140 TERHADAP KEAUSAN DAN UMUR MATA PAHAT KARBIDA Sobron Y. Lubis; Sofyan Djamil; Adianto Adianto; Amor Santosa; Edric VM.
Jurnal Ilmiah Teknik Mesin POROS Vol 17, No 1 (2021): Jurnal Ilmiah Teknik Mesin Poros
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (591.484 KB) | DOI: 10.24912/poros.v17i1.15394

Abstract

In the machining process, increased production can be done by increasing the use of cuttingparameters. However, the use of high cutting parameters has an effect on the wear of the cutting toolused. The aim of this research is to analyze the wear and tear that occurs on cutting tools and tool lifewhen cutting AISI 4140 steel by using variations in cutting speed. The machining process uses a CNClathe by turning the surface of the AISI 4140 steel workpiece. The wear criteria are determined when thecutting tool has reached the edge wear limit (VB) of 0.3 mm. Observation and measurement of carbidecutting tools are carried out every 5 minutes the machining process is carried out. If the cutting tool hasnot shown the specified wear value, then the cutting tool then cuts, so that the wear value is obtained.From the research conducted it was found that at a cutting speed of 160 m / min the cutting tool iscapable of cutting for 39 minutes, 13 seconds. At a cutting speed of 180 m / min the cutting tool is capableof cutting for 38 minutes, 14 seconds. At a cutting speed of 200 m / min the cutting tool is capable ofcutting for 33 minutes, 8 seconds. At a cutting speed of 240 m / min the cutting tool is capable of cuttingfor 26 minutes, 3 seconds. Taylor's advanced tool life for the coated carbide cutting tool in turning AISI4140 steel material is: Vc. Tl.0.073 = 8203.
PENENTUAN KECEPATAN PEMOTONGAN EFEKTIF BERDASARKAN NILAI KEKASARAN PERMUKAAN MATERIAL AA-7075 PADA PROSES FACE MILLING Sobron Y. Lubis; Rosehan Rosehan; Musa Law
Jurnal Ilmiah Teknik Mesin POROS Vol 17, No 1 (2021): Jurnal Ilmiah Teknik Mesin Poros
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (627.731 KB) | DOI: 10.24912/poros.v17i1.15400

Abstract

During face milling machining, several machining parameters such as feed rate and cuttingspeed determine the surface quality of the workpiece produced by the process. The selection of the rightparameters will lead to the surface quality as planned. Therefore, to improve machining effectiveness, amethod is needed to determine the appropriate machining parameters to produce the desired surfacequality. This research was conducted using a milling machine, five variations of cutting speed and fivevariations of feed rate were used to cut the workpiece aluminum alloy 7075. After machining, the surfaceroughness was measured using a surface test. The surface roughness value is then substituted into thefeed rate equation and effective cutting speed. By finding effective cutting parameters, the machiningprocess will be more efficient and effective without using unnecessary resources. From the results of thestudy note that the development equation to determine the feed rate based on the value of surfaceroughness is ???? = 0,6????√???? ????????0.443mm/tooth. Development equation to determine the effective cutting speedbased on Surface roughness value is ???????? = 3.0686????????0.124 mm/min
Co-Authors Adianto Adianto Amor Santosa Edric VM. Musa Law Rosehan Rosehan Sofyan Djamil