Claim Missing Document
Check
Articles

Found 4 Documents
Search

Rancang Bangun Alat Metal Detector dengan Metode Beat Frequency Oscillator Suhaesih Rianto; Syahrir Syahrir; Adrianus Inu Natalisanto
Progressive Physics Journal Vol 3 No 2 (2022): Progressive Physics Journal
Publisher : Program Studi Fisika, Jurusan Fisika, FMIPA, Universitas Mulawarman

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (468.389 KB) | DOI: 10.30872/ppj.v3i2.957

Abstract

A metal detector using the Beat Frequency Oscillator principle and solenoid induction has been made using a series of tools (IC NE 555, capacitors with values ​​of 3.3 F and 4.7 F, resistors 4.9 kΩ, enamel wire 0.3 mm, 4Ω 3W speakers, and 9V battery). The measuring limit of the tool is obtained through measurements using a metal material, namely iron, where the measured value variables are the value of frequency and voltage Vpp, and the average value of the frequency in the input data after the object is 868.1786 Hz and the average value of the Vpp voltage is 1,427 Volts. While the output data obtained the average frequency value is 863.4895 Hz and the average value of Vpp voltage is 0.325 Volt after the object, as for the sound produced before and after the object the difference is too small, so an amplifier circuit is added using an IC LM386 as Audio Amplifier.
Analisis Koefisien Serapan (Absorbsi) kebisingan pada Bahan Kayu (Triplek, Papan Kayu dan Kalsiboard) siti istikhomah; Syahrir Syahrir; Adrianus Inu Natalisanto
Progressive Physics Journal Vol 2 No 1 (2021): Progressive Physics Journal
Publisher : Program Studi Fisika, Jurusan Fisika, FMIPA, Universitas Mulawarman

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1481.755 KB) | DOI: 10.30872/ppj.v2i1.748

Abstract

Noise is a sound that humans do not want and it is an environmental factor that can negatively affect health. To overcome the noise issue, many efforts have been made to reduce noise levels. An example is the manufacture of the walls of a house using materials with sound and absorbent standards. The materials used can also be derived from types of wood such as plywood, wood panels and calciboards. Therefore, the value of its sound absorption coefficient is calculated to find out which active material is to be used in the manufacture of the building. Based on the research results, the value of the sound absorption coefficient of the three types of materials, it can be seen that the shape of the graph and its analysis states that the lowest sound absorption coefficient is most likely at the lower frequencies and the highest value of the sound absorption coefficient tends to be at the higher frequencies. In fact, when viewed as a whole, the magnitude and magnitude of the sound absorption coefficient on the graph is not in line with the increase in the frequency value.
Rancang Bangun Prototipe Monitoring Suhu dan Kelembaban Udara Berbasis Internet Of Things (IOT) Pada Laboratorium Kalibrasi Balai Pengujian dan Sertifikasi Mutu Barang Samarinda Muhammad Awaluddin; Syahrir Syahrir; Ahmad Zarkasi; Erlinda Ratnasari Putri
Progressive Physics Journal Vol 3 No 1 (2022): Progressive Physics Journal
Publisher : Program Studi Fisika, Jurusan Fisika, FMIPA, Universitas Mulawarman

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (778.175 KB) | DOI: 10.30872/ppj.v3i1.910

Abstract

Telah dilakukan penelitian tentang rancang bangun prototipe monitoring suhu dan kelembaban udara berbasis internet of things (IoT) pada Labratorium Kalibrasi Balai Pengujian dan Sertifikasi Mutu Barang (BPSMB) Samarinda. Penelitian ini bertujuan merancang prototipe yang dapat mengukur suhu dan kelembaban udara menggunakan sensor BME280 berbasis mikrokontoler NodeMCU ESP8266. Tahapan penelitian dilakukan dengan merancang perangkat keras dan perangkat lunak prototipe menggunakan BME280 sebagai sensor yang dapat mengukur suhu dan kelembaban udara dan NodeMCU ESP8266 sebagai kontrol utama yang dilakukan di Laboratorium Elektronika dan Instrumentasi Universitas Mulawarman. Tahap selanjutnya, dilakukan pemantauan suhu dan kelembaban udara di Laboratorium Kaibrasi Balai Pengujian dan Sertifikasi Mutu Barang Samarinda. Hasil perancangan prototipe dapat mengukur suhu dan kelembaban udara seacara realtime serta dapat dimonitoring menggunakan smartphone melalui aplikasi blynk dan hasil monitoring di Laboratorium Kalibrasi BPSMB Samarinda menunjukkan bahwa laboratorium tersebut berada pada suhu ideal yaitu 18 - 22 sesuai standar acuan JIS Z 8710 (Japanese Industrial Standard).
APLIKASI SENSOR MICRO ELECTRO MECHANICAL SYSTEM (MEMS) ACCELEROMETER BERBASIS IOT DALAM PENGUKURAN PERCEPATAN MAKSIMUM GETARAN STRUKTUR JEMBATAN Rafika Ade Rahayu; Kholis Nurhanafi; Syahrir Syahrir; Ahmad Zarkasi
Jurnal Informatika dan Teknik Elektro Terapan Vol 12, No 2 (2024)
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jitet.v12i2.4134

Abstract

Alat ukur getaran dengan sensor Micro Electro Mechanical System (MEMS) berbasis Internet of Things (IoT) merupakan alat yang dapat diaplikasikan pada pengukuran nilai percepatan maksimum getaran struktur jembatan. Tujuan penelitian ini adalah untuk merancang alat ukur getaran dengan sensor MEMS berbasis IoT dengan harga yang relatif rendah dan mengukur standar deviasi pada alat ukur tersebut. Pada penelitian ini alat ukur dibuat dengan sensor MEMS tipe ADXL345 yang dihubungkan dengan mikrokontroler NodeMCU Esp8266 lalu diprogram pada interface Arduino IDE agar dapat terhubung dengan platform IoT Blynk. Sistem alat ukur yang dirancang dapat merekam data pada Cloud Blynk dengan nilai sampling 1 Hz. Nilai standard deviasi pada 3 titik pengukuran jembatan tiap sumbunya yaitu: pada titik 1 dengan sumbu x, y, dan z secara berturut-turut sebesar 0.0137 g, 0.0163 g, 0.0228 g; titik 2 sumbu x, y, z secara berturut-turut sebesar 0.0139 g, 0.0195 g, 0.0299 g; titik 3 sumbu x, y, z secara berturut-turut sebesar 0.0139 g, 0.0285 g, 0.0313 g.