Article Per Year (5 Year)
p-Index From 2021 - 2026
0.61
P-Index
This Author published in this journals
All Journal Journal of ICT, Design, Engineering and Technological Science
Muhammad Abdur Rehman Hamid
Unknown Affiliation
Civil Engineering, Building, Construction & Architecture Computer Science & IT Electrical & Electronics Engineering Engineering Mechanical Engineering

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search
Journal : Journal of ICT, Design, Engineering and Technological Science

 1 
Optimum Utilization of Volcanic Rock as Pozzolana for the Maximum Compressive Strength of Mortar Zeeshan Ahmad; Muhammad Suleman; Masooma Sabtain; Muhammad Abdur Rehman Hamid; Waqas ur Rahman; Hamid Bilal
Journal of ICT, Design, Engineering and Technological Science Volume 7, Issue 2
Publisher : Journal of ICT, Design, Engineering and Technological Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33150/JITDETS-7.2.4

Abstract

This research describes the Dir-Utror volcanics in terms of geochemical analysis and compressive strength results to determine their Pozzolanic properties. Adding pozzolana to cement mortar enhances compressive strength by providing a supplementary binding material that reacts with calcium hydroxide to form additional cementitious compounds. This not only improves the overall durability of the mortar but also reduces the risk of cracks, making it an economically viable solution for constructing robust and long-lasting structures. For this purpose, this research concentrates on exploring the Pozzolanic characteristics using the X-ray Florescence technique, to illustrate chemical composition, and compressive strength test using 2 inch or 50 mm mortar cube. According to chemical composition and compressive strength results and by comparing it with the standard cube compression results with Ordinary Portland Cement (OPC), these materials are suitable to use as an additive or substitute for cement replacement. Four different samples were collected from the same region three of them, at 28 days of age, gave satisfactory results, while a single sample (sample 2) had less compression result than the standard cubes, cured for 28 days, according to the graphs’ trend lines. A total of 78 (2-inch) cubes were made, 6 considered to be standard (OPC) and 72 for 4 different samples. Three cubes for each ratio, such as by 15%, 25 and 35%, have been prepared and have taken the average value for each Pozzolan-ratio sample. The 1st series, 36 Pozzolan cubes’, compressive strength results were conducted after 14 days of age which was not as satisfactory as the 2nd series cured for 28 days of age.
Strength Analysis of Ultra-High-Performance U-H-P Steel Fibre Reinforced Mortar Part of Concrete Using Rice Husk Ash & Nano Silica Fume Kashif Alam; Arshad khan; Waqas Ur Rahman; Nadir Rehman Khattak; Muhammad Naveed Ur Rahman; Muhammad Abdur Rehman Hamid
Journal of ICT, Design, Engineering and Technological Science Volume 8, Issue 1
Publisher : Journal of ICT, Design, Engineering and Technological Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33150/JITDETS-8.1.2

Abstract

The purpose of this study is to provide Pakistani citizens with Ultra-High-Performance Concrete utilizing locally available resources. In an experimental study, steel fibres are combined with silica fume and rice husk ash when superplasticizers are present. Several different tests were done using completely different volumes and different amounts of ingredients from local supplies and steel fibres to investigate ultra-high-performance concrete. Results show that ultra-high-performance concrete can be produced using locally accessible material. There are differences in the compressive and flexural strengths of the Ultra High-Performance concrete. Every outcome is pleasing. Scanning electron microscopy and X-ray diffraction tests were also used to assess the ultra-high-performance concrete's microstructural analysis. The transition zone between fine aggregates and the cement paste is enhanced by the use of silica, according to X-ray diffraction and scanning electron microscopy test results. Dense packing is one of the main factors influencing concrete strength, and it is achieved by using a low water to-cement ratio. This observation is gained from Scanning Electron Microscopy and X-ray diffraction tests. The steel fibers in ultra-high-performance concrete inhibited the propagation of cracks in the matrix.
Optimization of Engineering Properties and XRD Pattern of the Conventional Brick by Recycling the Discarded Cigarette Butts Shoaib Muhammad; Zeeshan Ahmad; Muhammad Abdur Rehman Hamid; Waqas ur Rahman; Talha Saleem; Muhammad Jahangir Khan
Journal of ICT, Design, Engineering and Technological Science Volume 7, Issue 2
Publisher : Journal of ICT, Design, Engineering and Technological Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33150/JITDETS-7.2.5

Abstract

Cigarette butts are one of the integral pollutants that severely crank the major public spots like streets, roadsides, seashores, river canals, etc. Apart from this, they have a secondary effect in which they provide space for other trash materials. If they are not properly disposed of then they will slowly burn for an out three hours. Thousands of kilograms of harmful waste are created annually from a few tones of cigarettes produced worldwide. Because cellulose acetate filters are not very biodegradable, Cigarette Butts (CBs) accumulate in the environment. A portion of the findings from an ongoing study on repurposing cigarette butts into baked clay bricks are presented in this report. Cigarette butts have been utilized to make bricks for this project. Based on the test findings, the bricks' compressive strength was found to be 37%, 53.2%, and 79.7% lower than that of typical bricks, with CB percentages of 4, 8, and 12, respectively. Also, water absorption of the brick was increased by 8%, 16%, and 48 % with CB percentages 4, 8, and 12 respectively than normal brick water absorption. Thermal conductivity of bricks was also reduced with using CBs much in amount and thermal insulation was improved by almost 50% on 4% of CBs dosage which is the optimum percentage. XRD pattern shows the Sio2 quartz in maximum with some other ingredients like feldspar, hematite and orthoclase, etc. means that the results revealed amounts of heavy metals.
Co-Authors Arshad Khan Hamid Bilal Kashif Alam Masooma Sabtain Muhammad Jahangir Khan Muhammad Naveed Ur Rahman Muhammad Suleman Nadir Rehman Khattak Shoaib Muhammad Talha Saleem Waqas ur Rahman Zeeshan Ahmad