p-Index From 2021 - 2026
0.444
P-Index
This Author published in this journals
All Journal Jurnal Polimesin
Claim Missing Document
Check
Articles

Found 2 Documents
Search

Microstructure and deformation behavior of Cu–Zn–Al–(Si) shape memory alloys under quenching controlled from the α/β phase region Atik Setyani; Hendy Roesma Wardhana; Nur Amin; Ignatius Andre Setiawan; Nina Fapari Arif
Jurnal Polimesin Vol 23, No 6 (2025): December
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v23i6.7802

Abstract

Shape Memory Alloys (SMAs) are functional materials with rapidly expanding applications in medical devices, aerospace, and smart actuators. Among them, Cu–Zn–Al-based SMAs are cost-effective but their performance is often limited by the formation of non-reversible martensite. This study investigates the influence of Si addition and quenching methods on the microstructure, martensitic transformation, and deformation behavior of Cu–Zn–Al SMAs. Alloys with compositions of Cu–27Zn–2.5Al and Cu–27Zn–2.5Al–0.3Si wt.% were fabricated via gravity casting and homogenized at 850°C for 2 hours. The samples were then betatized at 900°C for 30 minutes and cooled using two quenching methods: Direct Quenching (DQ) and Up Quenching (UQ). The UQ process involved reheating after initial quenching to promote atomic ordering and defect relaxation, followed by cooling in an ethanol+dry ice mixture maintained at –5°C. The results reveal that the Cu–27Zn–2.5Al wt.% alloy undergoes a β → β′ martensitic transformation in both DQ and UQ conditions, with UQ producing a more homogeneous and responsive martensitic structure. In contrast, the addition of 0.3 wt.% Si refines the α-phase grains and stabilizes the α + β phase region, thereby suppressing martensite formation. The Si-containing alloy deforms mainly through plastic slip in the α phase, whereas the Si-free alloy exhibits the typical twinning/detwinning mechanism of SMAs. These findings confirm that the combination of alloy composition and quenching route governs phase transformation and deformation mechanisms in Cu-based SMAs, offering insight for designing low-cost functional materials with tunable shape memory behavior.
Effect of hybrid reinforcement and heat treatment on phase evolution, microstructure, and hardness of Al6061/SiC/MWCNT/graphite composites Atik Setyani; Muhammad Syukron; Ibnu Cahyo Nugroho; Agris Setiawan
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.8904

Abstract

The development of lightweight and high-strength materials is increasingly important for transportation and aerospace applications. Al6061 is a promising structural alloy; however, its mechanical performance can be limited by microstructural heterogeneity and the distribution of strengthening phases. Although SiC, carbon-based reinforcements, and T6 heat treatment have been individually investigated in Al6061 composites, the combined response of SiC/MWCNT/graphite hybrid reinforcement to T6 treatment, particularly in terms of phase evolution, microstructural distribution, and hardness, remains insufficiently understood. This study investigated Al6061 hybrid composites reinforced with SiC, MWCNTs, and graphite produced by stir casting and subsequently subjected to homogenization, solution treatment, rapid quenching, and artificial aging. Microstructural and phase characterization was performed using optical microscopy, SEM-EDS, and XRD, while hardness was evaluated using the Rockwell B scale. The untreated composite consisted primarily of an α-Al matrix containing Mg2Si and dispersed reinforcing particles, although localized graphite agglomeration was observed. Heat treatment promoted a more homogeneous microstructure and modified the distribution of Mg2Si precipitates. XRD confirmed the presence of FCC α-Al, Mg2Si, and reinforcement-related phases. The heat-treated composite exhibited the highest hardness of 48.28 HRB, compared with 45.22 HRB for the untreated composite and 22.68 HRB for unreinforced Al6061. The hardness improvement is attributed to the combined contributions of hybrid reinforcement and precipitation strengthening. These results demonstrate the role of T6 heat treatment in tailoring the microstructure and hardness of Al6061/SiC/MWCNT/graphite hybrid composites.