Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

International Journal of Science and Engineering (IJSE)

ijse
Website

Published by Universitas Diponegoro

ISSN : - EISSN : - DOI : -

Core Subject : Engineering,

Engineering

The scope of journal covers all area in the application on chemical, physical, mathematical, biological, agricultural, corrossion, and computer science to solve the engineering problems.

Arjuna Subject : -

Articles 4 Documents

Search results for , issue "Vol 1, No 2 (2010)" : 4 Documents clear

The Effect of Feed to Inoculums Ratio on Biogas Production Rate from Cattle Manure Using Rumen Fluid as Inoculums S. Sunarso; Seno Johari; I Nyoman Widiasa; B. Budiyono
International Journal of Science and Engineering Vol 1, No 2 (2010)
Publisher : Chemical Engineering Diponegoro University

In this study, rumen fluid of animal ruminant was used as inoculums to increase biogas production rate from cattle manure at mesophilic condition. A series of laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid and tap water resulting five different feed to inoculum (F/I) ratios (i.e. 17.64, 23.51, 35.27, and 70.54). The operating temperatures were varied at room temperature. The results showed that the rumen fluid inoculated to biodigester significantly effected the biogas production. Rumen fluid inoculums caused biogas production rate and efficiency increase more than two times in compare to manure substrate without rumen fluid inoculums. At four F/Is tested, after 80 days digestion, the biogas yield were 191, 162, 144 and 112 mL/g VS, respectively. About 80% of the biogas production was obtained during the first 40 days of digestion. The best performance of biogas production will be obtained if F/I ratio is in the range of 17.64 to 35.27 (correspond to 25 – 50 % of rumen fluid). The future work will be carried out to study the dynamics of biogas production if both the rumen fluid inoculums and manure are fed in the continuous system

Bioconversions of Palm Kernel Cake and Rice Bran Mixtures by Trichoderma viride Toward Nutritional Contents Yana Sukaryana; Umi Atmomarsono; Vitus D. Yunianto; Ejeng Supriyatna
International Journal of Science and Engineering Vol 1, No 2 (2010)
Publisher : Chemical Engineering Diponegoro University

The objective of the research is to examine the mixtures of palm kernel cake and rice bran of fermented by Trichoderma viride. Completely randomized design in factorial pattern 4 x 4 was used in this experiment. factor I is the doses of inoculums; D1 = 0%, D2 = 0,1% , D3 = 0,2%, D4 = 0,3%, and complement factor II is mixtures of palm kernel cake and rice bran : T1=20:80% ; T2=40:60% ; T3=60:40% ; T4=80:20%. The treatment each of three replicate. Fermentation was conducted at temperature 28 oC as long as 9 days. Determining the best of the mixtures be based on the crude protein increased and the crude fibre decreased. The results showed that the combination of product mix is the best fermentation inoculums doses 0.3% in mixture of palm kernel cake and rice bran ; 80%: 20%, which produces dry matter of 88,12%, crude protein 17.34%, ether extract 5,35%, crude fibre 23.67%, and ash 6.43%. When compared with a mixture of palm kernel cake and rice bran; 80%: 20% without of fermentation is crude protein increase 29.58% and crude fibre decreased 22.53%.

Biogas Production Using Anaerobic Biodigester from Cassava Starch Effluent S. Sunarso; B. Budiyono; Siswo Sumardiono
International Journal of Science and Engineering Vol 1, No 2 (2010)
Publisher : Chemical Engineering Diponegoro University

IKMs’ factory activity in Margoyoso produces liquid and solid wastes. The possible alternative was to use the liquid effluent as biogas raw material. This study focuses on the used of urea, ruminant, yeast, microalgae, the treatment of gelled and ungelled feed for biogas production, pH control during biogas production using buffer Na2CO3, and feeding management in the semi-continuous process of biogas production that perform at ambient temperature for 30 days. Ruminant bacteria, yeast, urea, and microalgae was added 10% (v/v), 0.08% (w/v), 0.04% (w/v), 50% (v/v) of mixing solution volume, respectively. The pH of slurry was adjusted with range 6.8-7.2 and was measured daily and corrected when necessary with Na2CO3. The total biogas production was measured daily by the water displacement technique. Biogas production from the ungelling and gelling mixture of cassava starch effluent, yeast, ruminant bacteria, and urea were 726.43 ml/g total solid and 198 ml/g total solid. Biogas production from ungelling mixture without yeast was 58.6 ml/g total solid. Biogas production from ungelling mixture added by microalgae without yeast was 58.72 ml/g total solid and that with yeast was 189 ml/g total solid. Biogas production from ungelling mixture of cassava starch effluent, yeast, ruminant bacteria, and urea in semi-continuous process was 581.15 ml/g total solid. Adding of microalgae as nitrogen source did not give significant effect to biogas production. But adding of yeast as substrate activator was very helpful to accelerate biogas production. The biogas production increased after cassava starch effluent and yeast was added. Requirement of sodium carbonate (Na2CO3) to increase alkalinity or buffering capacity of fermenting solution depends on pH-value

The Influence of Casting Machine Speed in Cellulose Acetate Membrane Preparation Luqman Buchori
International Journal of Science and Engineering Vol 1, No 2 (2010)
Publisher : Chemical Engineering Diponegoro University

Membranes are being increasingly used as a valuable separation tool in laboratory as well as in industrial processes. Continual development of new membrane materials is crucial to sustain and expand the growing interest in this technology and modern polymer chemistry is highly proficient in tailoring polymers with desired properties such as increased mechanical, thermal and chemical stability. Cellulose acetate (CA) is one of the membrane polymers that has been used for aqueous based separation and used as both reverses osmosis (RO) and ultrafiltration (UF) membranes. This paper presents investigation of influence of casting machine speed in membrane preparation. CA is used in this study. That was CA-398-30 with average acetyl content 39.8 wt %. Non solvent used is water and the solvent is 99.7 % organic Dimethyl Sulfoxide (DMSO). The homogenous CA/DMSO solutions were prepared by dissolving CA in DMSO solvent. The CA concentration were varied 13 and 16 % while casting solution speed were varied from 20 to 80 mm/sec with distance cutting machine were fixed at 14 cm. In addition, non solvent in coagulation bath also were varied by 100 % water and 10 % DMSO in water. The results of this experiment describe effect of casting machine speed to water permeability. The effect of CA concentration to water permeability shows the adversative result between 13 and 16 % CA in 100 non solvent water. The similar result also observed in 10 % DMSO in water.

Page 1 of 1 | Total Record : 4

Filter by Year

2010 2010

Filter By Issues

All Issue Vol 13, No 1 (2019) Vol 10, No 2 (2016) Vol 10, No 1 (2016) Vol 9, No 2 (2015) Vol 9, No 1 (2015) Vol 8, No 2 (2015) Vol 8, No 1 (2015) Vol 7, No 2 (2014) Vol 7, No 1 (2014) Vol 6, No 2 (2014) Vol 6, No 1 (2014) Vol 5, No 2 (2013) Vol 5, No 1 (2013) Vol 4, No 2 (2013) Vol 4, No 1 (2013) Vol 3, No 2 (2012) Vol 3, No 1 (2012) Vol 2, No 2 (2011) Vol 2, No 1 (2011) Vol 1, No 2 (2010) Vol 1, No 1 (2010) ARTICLE IN PRESS More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota semarang,

Jawa tengah

INDONESIA

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kota semarang, Jawa tengah INDONESIA

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota semarang,

Jawa tengah

INDONESIA