cover
Contact Name
Tole Sutikno
Contact Email
ijece@iaesjournal.com
Phone
-
Journal Mail Official
ijece@iaesjournal.com
Editorial Address
-
Location
Kota yogyakarta,
Daerah istimewa yogyakarta
INDONESIA
International Journal of Electrical and Computer Engineering
ISSN : 20888708     EISSN : 27222578     DOI : -
International Journal of Electrical and Computer Engineering (IJECE, ISSN: 2088-8708, a SCOPUS indexed Journal, SNIP: 1.001; SJR: 0.296; CiteScore: 0.99; SJR & CiteScore Q2 on both of the Electrical & Electronics Engineering, and Computer Science) is the official publication of the Institute of Advanced Engineering and Science (IAES). The journal is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world.
Articles 73 Documents
Search results for , issue "Vol 8, No 3: June 2018" : 73 Documents clear
Design of an Interdigital Structure Planar Bandpass Filter for UWB Frequency S. M. A. Motakabber; M. N. Haidari
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (576.189 KB) | DOI: 10.11591/ijece.v8i3.pp1654-1658

Abstract

A new topology of miniaturized interdigital structuremicrostrip planar bandpass filter for Ultra-Wideband (UWB) frequency has been discussed in this paper. The proposed design and its simulation have been carried out by using an electromagnetic simulation software named CST microwave studio. The Taconic TLX-8 microwave substrate has been used in this research. The experimental result and analysis have been performed by using the microwave vector network analyzer. The experimental result showed that the -10dB bandwidth of the filter is 7.5GHz. The lower and upper corner frequencies of the filter have been achieved at 3.1GHz and 10.6GHz respectively. At the center frequency of 6.85GHz, the -1dB insertion loss and the -7dB return losshave been observed. The simulated and experimental results are well agreed with a compact size filter of 19×21×0.5mm3.
Residual Current Measurement using Helmholtz Coil Configuration with different Current Flow Erwin Sutanto; Frangky Chandra; Eduardo Gonnelli; Suhariningsih Suhariningsih
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (928.057 KB) | DOI: 10.11591/ijece.v8i3.pp1432-1441

Abstract

For leakage current safety, Residual Current Device (RCD) has been well known. The purpose of this work is to make the employment of low price components to measure residual current feasible and the Residual Current Device (RCD) must to be taken into account because it is a well known device for leakage current safety. For this purpose, experiments employing the Helmholtz Coil Configuration were performed with the different current flow. Furthermore, the residual current was formulated and simulated through the software Easy Java Simulation (EJS). The results showed that it is possible to move the magnet into different angles using leakage current with linear gradient as low as 0.382 degree/mA. Finally, it was proposed a way to increase the sensitivity and to reduce the hysteresis phenomenon.
Antenna Azimuth Position Control System using PID Controller & State-Feedback Controller Approach Aveen Uthman; Shahdan Sudin
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (857.672 KB) | DOI: 10.11591/ijece.v8i3.pp1539-1550

Abstract

This paper analyzed two controllers with the view to improve the overall control of an antenna azimuth position. Frequency ranges were utilized for the PID controller in the system; while Ziegler-Nichols was used to tune the PID parameter gains. A state feedback controller was formulated from the state-space equation and pole-placements were adopted to ensure the model design complied with the specifications to meet transient response. MATLAB Simulink platform was used for the system simulation. The system response for both the two controllers were analyzed and compared to ascertain the best controller with best azimuth positioning for the antenna. It was observed that state-feedback controller provided the best azimuth positioning control with a little settling time, some value of overshoot and no steady-state error is detected.
Unit Commitment Problem in Electrical Power System: A Literature Review Idriss Abdou; Mohamed Tkiouat
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (835.36 KB) | DOI: 10.11591/ijece.v8i3.pp1357-1372

Abstract

Unit commitment (UC) is a popular problem in electric power system that aims at minimizing the total cost of power generation in a specific period, by defining an adequate scheduling of the generating units. The UC solution must respect many operational constraints. In the past half century, there was several researches treated the UC problem. Many works have proposed new formulations to the UC problem, others have offered several methodologies and techniques to solve the problem. This paper gives a literature review of UC problem, its mathematical formulation, methods for solving it and Different approaches developed for addressing renewable energy effects and uncertainties.
Selection of Digital Filter for Microprocessor Protection Relays Denis B. Solovev
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (793.887 KB) | DOI: 10.11591/ijece.v8i3.pp1498-1512

Abstract

The article considers some issues related to replacement of electromechanical relays used for protection of power facilities with microprocessor relays. One of the urgent problems connected with implementation of microprocessor overcurrent protections is how to use current transducers other than usual current transformers and in particular Rogowski coils that become more and more widespread. In the article are compared twelve methods of synthesis of a digital filter basing on the analog prototype – second-order integrating filter. The bilinear filter and Boxer-Thaler filters are analyzed in respect to their use in microprocessor relays. Basing on the research results a technique for selection of parameters of digital integrating filters for microprocessor relays is proposed. Simulation results show that Boxer-Thaler and bilinear filters have better accuracy during transient current measurements than the analog filter. The study allows concluding that in many cases the digital second-order bilinear filter is the best choice for use in microprocessor relays.
Dual Axes Solar Tracker Ahmad Imran bin Ibrahim; Farah Diyana binti Abdul Rahman; Muazzin bin Rohaizat
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (599.101 KB) | DOI: 10.11591/ijece.v8i3.pp1887-1892

Abstract

Photovoltaic (PV) is one of the most important sources of renewable energy in the world. Its current efficiency could be increased up to 60% by using dual axes solar tracker, which maximise PV exposure to sun. The most important component in dual axes solar tracker is sensing location of the sun. Four light dependent resistors (LDR) are used as the sensors, connected to potentiometers to increase their accuracy. Arduino UNO is used as the controller to control two stepper motors. Two experiments have been carried out, where the tolerance of the LDR has been found to be 0.05V and the calibration of the four LDRs to have the error of 0.03V. Both experiments proved the capability of LDR for dual axes solar tracker and potentiometer to increase their accuracy.
Soft Frequency Reuse (SFR) in LTE-A Heterogeneous Networks based upon Power Ratio Evaluation Alvita Maurizka; F. Hamdani; M. M. Ulfah; Iskandar Iskandar
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (788.443 KB) | DOI: 10.11591/ijece.v8i3.pp1569-1576

Abstract

As the traffic demand grows and the RF environment changes, the mobile network relies on techniques such as SFR in Heterogeneous Network (HetNet) to overcome capacity and link budget limitation to maintain user experience. Inter-Cell Interference (ICI) strongly affecting Signal-to-Interference plus Noise Ratio (SINR) of active UEs, especially cell-edge users, which leads to a significant degradation in the total throughput. In this paper we evaluate the performance of SFR with HetNet system in order dealing with interferences. Simulation result shows that the power ratio control in SFR HetNet system doesn’t have much effect on total achieved capacity for overall cell.
A Compact Dual Band Elliptical Microstrip Antenna for Ku/K Band Satellite Applications Mohamed Mahfoudh Harane; Hassan Ammor
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (537.147 KB) | DOI: 10.11591/ijece.v8i3.pp1596-1601

Abstract

This paper presents an original elliptical microstrip patch antenna is proposed for Ku/K band satellite applications. The proposed antenna has a simple structure, small size with dimensions of about 10×12×1.58 mm³. The antenna has been designed and simulated on an FR4 substrate with dielectric constant 4.4 and thickness of 1.58 mm. The design is simulated by two different electromagnetic solvers. The results from the measured data show that the antenna has two resonant frequencies that define 2 bandwidths, defined by a return loss of less than -10 dB, and are: (14.44 GHz, 829 MHz) and (21.05 GHz, 5126 MHz),with the gain 5.59 dB and 5.048 dB respectively. The proposed antenna can be used in many applications such as in satellite, and wireless communications.
Dynamic Voltage Stability Comparison of Thermal and Wind Power Generation with Different Static and Dynamic Load Models Lina F. Acevedo; Gilbert Bothia-Vargas; John Edwin Candelo
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (473.994 KB) | DOI: 10.11591/ijece.v8i3.pp1401-1411

Abstract

This paper presents a static and dynamic voltage stability analysis of a power network with thermal and wind generation considering static and dynamic load models. The thermal plant was modeled as a synchronous machine and the wind farm as a variable speed induction generator based on a doubly-fed induction generator. The load considered the ZIP, exponential recovery, induction motor, and frequency-dependent load models. The bifurcation points were found by continuation power flow and sensitivity analyses. In addition, dynamic voltage stability assessments were performed considering changes in the moment of inertia and the frequency parameters. All simulations were carried out in a 4-bus power system and using the power system analysis toolbox (PSAT) and MATLAB script code. The results show that the thermal generator had difficulties to maintain stability under dynamic load variations and frequency changes, the wind generator had difficulties to maintain voltage for the load with induction motors, and both generators had difficulties when the moment of inertia is increased.
A Survey of Machine Learning Techniques for Self-tuning Hadoop Performance Md. Armanur Rahman; J. Hossen; Venkataseshaiah C; CK Ho; Tan Kim Geok; Aziza Sultana; Jesmeen M. Z. H.; Ferdous Hossain
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (475.262 KB) | DOI: 10.11591/ijece.v8i3.pp1854-1862

Abstract

The Apache Hadoop framework is an open source implementation of MapReduce for processing and storing big data. However, to get the best performance from this is a big challenge because of its large number configuration parameters. In this paper, the concept of critical issues of Hadoop system, big data and machine learning have been highlighted and an analysis of some machine learning techniques applied so far, for improving the Hadoop performance is presented. Then, a promising machine learning technique using deep learning algorithm is proposed for Hadoop system performance improvement.

Filter by Year

2018 2018


Filter By Issues
All Issue Vol 15, No 5: October 2025 Vol 15, No 4: August 2025 Vol 15, No 3: June 2025 Vol 15, No 2: April 2025 Vol 15, No 1: February 2025 Vol 14, No 6: December 2024 Vol 14, No 5: October 2024 Vol 14, No 4: August 2024 Vol 14, No 3: June 2024 Vol 14, No 2: April 2024 Vol 14, No 1: February 2024 Vol 13, No 6: December 2023 Vol 13, No 5: October 2023 Vol 13, No 4: August 2023 Vol 13, No 3: June 2023 Vol 13, No 2: April 2023 Vol 13, No 1: February 2023 Vol 12, No 6: December 2022 Vol 12, No 5: October 2022 Vol 12, No 4: August 2022 Vol 12, No 3: June 2022 Vol 12, No 2: April 2022 Vol 12, No 1: February 2022 Vol 11, No 6: December 2021 Vol 11, No 5: October 2021 Vol 11, No 4: August 2021 Vol 11, No 3: June 2021 Vol 11, No 2: April 2021 Vol 11, No 1: February 2021 Vol 10, No 6: December 2020 Vol 10, No 5: October 2020 Vol 10, No 4: August 2020 Vol 10, No 3: June 2020 Vol 10, No 2: April 2020 Vol 10, No 1: February 2020 Vol 9, No 6: December 2019 Vol 9, No 5: October 2019 Vol 9, No 4: August 2019 Vol 9, No 3: June 2019 Vol 9, No 2: April 2019 Vol 9, No 1: February 2019 Vol 8, No 6: December 2018 Vol 8, No 5: October 2018 Vol 8, No 4: August 2018 Vol 8, No 3: June 2018 Vol 8, No 2: April 2018 Vol 8, No 1: February 2018 Vol 7, No 6: December 2017 Vol 7, No 5: October 2017 Vol 7, No 4: August 2017 Vol 7, No 3: June 2017 Vol 7, No 2: April 2017 Vol 7, No 1: February 2017 Vol 6, No 6: December 2016 Vol 6, No 5: October 2016 Vol 6, No 4: August 2016 Vol 6, No 3: June 2016 Vol 6, No 2: April 2016 Vol 6, No 1: February 2016 Vol 5, No 6: December 2015 Vol 5, No 5: October 2015 Vol 5, No 4: August 2015 Vol 5, No 3: June 2015 Vol 5, No 2: April 2015 Vol 5, No 1: February 2015 Vol 4, No 6: December 2014 Vol 4, No 5: October 2014 Vol 4, No 4: August 2014 Vol 4, No 3: June 2014 Vol 4, No 2: April 2014 Vol 4, No 1: February 2014 Vol 3, No 6: December 2013 Vol 3, No 5: October 2013 Vol 3, No 4: August 2013 Vol 3, No 3: June 2013 Vol 3, No 2: April 2013 Vol 3, No 1: February 2013 Vol 2, No 6: December 2012 Vol 2, No 5: October 2012 Vol 2, No 4: August 2012 Vol 2, No 3: June 2012 Vol 2, No 2: April 2012 Vol 2, No 1: February 2012 Vol 1, No 2: December 2011 Vol 1, No 1: September 2011 More Issue