cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota padang,
Sumatera barat
INDONESIA
Jurnal Teknik Mesin
ISSN : 18298958     EISSN : 26555670     DOI : -
Jurnal Teknik Mesin adalah sebuah jurnal peer review yang didedikasikan untuk publikasi hasil penelitian yang berkualitas dalam bidang teknik mesin.
Arjuna Subject : -
Articles 225 Documents
Pengaruh Fraksi Serat terhadap Kekuatan Impak pada Lapisan Luar Komposit Honeycomb Jesaya Imanuel Soni Junior Pondaag; Imran Musanif; Artian Sirun
Jurnal Teknik Mesin Vol. 19 No. 1 (2026): Jurnal Teknik Mesin
Publisher : Politeknik Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30630/jtm.19.1.2211

Abstract

Sandwich composites with a bamboo honeycomb core and coconut coir fibre face plates offer an alternative for lightweight structures that must absorb impact energy. This study examines the effect of coir fibre volume fraction in the face plate on the impact energy and impact strength of the composite. Fibres were alkali-treated in sodium hydroxide for one hour, then moulded with epoxy resin into 2 mm face plates at volume fractions of 30%, 40% and 50%. The core was assembled from bamboo strips into hexagonal cells of 10 mm cell side, 20 mm wall height and 1 mm wall thickness. Testing followed the Izod method of ASTM D256 with three specimens per fraction, and impact strength was taken as absorbed energy divided by the 136 mm² cross-section. Mean impact energy reached 6.93 J at 30%, 9.67 J at 40% and 7.50 J at 50%, equivalent to impact strengths of 0.0510, 0.0711 and 0.0551 J/mm². Scatter was wide, with standard deviations of 2.52, 5.80 and 3.32 J, and one-way analysis of variance gave F(2,6) = 0.37 (p = 0.71). The 40% composition is therefore best read as a working indication that needs confirmation with more specimens and tighter process control.
Pengaruh Fraksi Volume Face Plate terhadap Kekuatan Impak Komposit Honeycomb Sabut Kelapa Adji Pramono Wirayudha; Adrian Maidangkay; Imran Musanif
Jurnal Teknik Mesin Vol. 19 No. 1 (2026): Jurnal Teknik Mesin
Publisher : Politeknik Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30630/jtm.19.1.2233

Abstract

The face plate of a sandwich composite receives the impact load first and transfers it to the core, so its proportion within the structure governs how much energy the whole structure can absorb. This study examines the effect of face plate volume fraction on the impact energy and impact strength of a honeycomb composite reinforced with coconut coir fibre. Face plate volume fractions of 30%, 40% and 50% were tested while the honeycomb core fraction was held at 30%. Each specimen combined two 20.1 mm wide, 2 mm thick face plates with two 10 mm high, 2 mm thick cell walls, giving a cross-sectional area of 120.4 mm². Testing followed the Izod method of ASTM D256 on an XJ-300A pendulum tester with a 29.4 J capacity released from 150°, using three specimens per fraction. Mean absorbed energy was 9.80 J at 30%, 15.67 J at 40% and 14.67 J at 50%, giving impact strengths of 0.0814, 0.1301 and 0.1218 J/mm². Raising the fraction from 30% to 40% increased impact strength by 59.9%, while a further rise to 50% reduced it by 6.4%. The relationship is therefore non-linear, and 40% gave the highest value among the fractions tested. One-way analysis of variance gave F(2,6) = 3.51 (p = 0.10), which falls short of significance at the 5% level, so the result is best treated as a strong indication rather than a settled optimum.
Peningkatan Performa Termal Bangunan dengan Menggunakan Atap UPVC Berbasis PCM Paraffin Wax dan Bees Wax Silviana Simbolon; Ahmad Syahrul Mubarok; Muhammad Yunus; Ihat Solihat
Jurnal Teknik Mesin Vol. 19 No. 1 (2026): Jurnal Teknik Mesin
Publisher : Politeknik Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30630/jtm.19.1.2263

Abstract

Indonesia is a tropical country characterized by relatively high air temperatures, which can reach 35 °C, and relative humidity levels of up to 80%. These conditions highlight the need for an effective passive cooling system to improve indoor thermal comfort. This study aims to analyze and compare the effectiveness of Phase Change Materials (PCMs) based on paraffin wax and beeswax in reducing roof and indoor temperatures. PCMs function by absorbing and releasing latent heat through phase-change processes, including liquid–gas and solid–solid transitions, known as Latent Heat Thermal Energy Storage (LHTES). An experimental method was employed, with temperature measurements digitally recorded using an Arduino IDE-based system. Temperature measurements were taken at several predetermined points to evaluate the thermal performance characteristics of each PCM variation. The experimental results showed that the roof without PCM resulted in an indoor temperature of 44.8 °C. The use of 100% beeswax reduced the indoor temperature by 4.36%. Meanwhile, a mixture of 75% paraffin wax and 25% beeswax achieved a temperature reduction of 5.39%. The best performance was obtained using a mixture of 50% paraffin wax and 50% beeswax, which reduced the temperature by up to 12.7%. Overall, the application of PCM reduced the indoor temperature by up to 2.36 °C compared with the condition without PCM. These results demonstrate that PCM has the potential to serve as an alternative passive cooling material for improving thermal comfort, particularly in buildings located in tropical climates.
Evaluasi Performa Waterjet Thruster Terhadap Gaya Dorong Berbasis Thermoplastic Polyurethane (TPU) Untuk Aplikasi Kapal Skala Kecil Muhamad Aris; Sugianto; Hasdiansah Hasdiansah
Jurnal Teknik Mesin Vol. 18 No. 2 (2025): Jurnal Teknik Mesin
Publisher : Politeknik Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Indonesia, as an archipelagic country, has great potential in developing efficient maritime propulsion systems. One alternative technology being explored is the waterjet thruster, a ship propulsion system that operates based on the principle of accelerating fluid flow through an impeller and nozzle. This study aims to examine the effect of nozzle size variation on the thrust produced by a waterjet thruster prototype fabricated using 3D printing technology with Thermoplastic Polyurethane (TPU) material. Two nozzle types were used: Type 1 (2-inch diameter) and Type 2 (2 × 1½-inch diameter). An experimental method was employed by measuring thrust under full and half throttle conditions using a dedicated thrust measuring device. The results show that Type 2 nozzle produced the highest thrust of 45.3222 N, while Type 1 produced only 40.46625 N. The 12% increase in thrust observed in Type 2 indicates that a nozzle design with a smaller cross-sectional area can optimize fluid flow efficiency and system performance. This study concludes that nozzle dimension significantly influences thrust efficiency, and a well-designed nozzle can offer an efficient and environmentally friendly propulsion solution for small vessels.
Uji Performa Gaya Dorong Pada Waterjet Thruster Menggunakan Material Stainless Steels 304 (SS 304) Ferzy Ersandy; Boy Rollastin; Hasdiansah Hasdiansah
Jurnal Teknik Mesin Vol. 19 No. 1 (2026): Jurnal Teknik Mesin
Publisher : Politeknik Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30630/jtm.19.1.2293

Abstract

A waterjet thruster is a ship propulsion system that operates by ejecting high-speed water through a nozzle to generate thrust. The system consists of main components such as the inlet turbo, impeller, and outlet turbo, all designed to maximize thrust efficiency. This study aims to evaluate the thrust performance of a waterjet thruster made from stainless steel 304 (SS304) through experimental testing by comparing the same object using different testing methods, namely variations in impeller rotational speed. The waterjet thruster consists of a 3-blade impeller, a 12-blade inlet turbo, and a 12-blade outlet turbo, manufactured through turning, welding, and assembly processes. The tests were carried out under two different operating conditions—1000 rpm and 1800 rpm—to assess the effect of different testing methods on thrust performance. The results show that increasing the rotational speed significantly increases the generated thrust. At 1000 rpm, the average thrust reached 74.163 N, while at 1800 rpm it increased to 122.919 N. This confirms that the system’s performance improves when the same object is tested under different operational methods, in this case a higher impeller rotation. SS304 material proved capable of maintaining its performance and is suitable for waterjet thruster components due to its mechanical properties and corrosion resistance