cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Triwiyanto
Contact Email
triwiyanto123@gmail.com
Phone
+628155126883
Journal Mail Official
editorial.jeeemi@gmail.com
Editorial Address
Department of Electromedical Engineering, Poltekkes Kemenkes Surabaya Jl. Pucang Jajar Timur No. 10, Surabaya, Indonesia
Location
Kota surabaya,
Jawa timur
INDONESIA
Journal of Electronics, Electromedical Engineering, and Medical Informatics
Published by Polilteknik Kesehatan Kemenkes Surabaya
ISSN : -     EISSN : 26568632     DOI : https://doi.org/10.35882/jeeemi
Core Subject : Science, Engineering,
Computer Science & IT Control & Systems Engineering Electrical & Electronics Engineering Engineering
The Journal of Electronics, Electromedical Engineering, and Medical Informatics (JEEEMI) is a peer-reviewed open-access journal. The journal invites scientists and engineers throughout the world to exchange and disseminate theoretical and practice-oriented topics which covers three (3) majors areas of research that includes 1) Electronics, 2) Biomedical Engineering, and 3)Medical Informatics (emphasize on hardware and software design). Submitted papers must be written in English for an initial review stage by editors and further review process by a minimum of two reviewers.
Arjuna Subject : Teknik (semua kategori) - Teknik Biomedis
Articles 6 Documents
 1 
Search results for , issue "Vol 2 No 1 (2020): January" : 6 Documents clear
Comparison of Flowrate and Occlusion in a Vertical Infusion Pump and Horizontal Infusion Pump Nur Hasanah Ahniar; Hendra Marwazi; Rismarini Yufita
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.1

Abstract

Infusion pump is a device used to enter fluid into the patient's body through a continuous. At present there are two types of infusion pumps namely vertical infusion pumps and horizontal infusion pumps. Both infusion pumps have different technologies. The aim of this study is to compare the performance results of the two infusion pumps. Infusion Pump is given 3 different liquid infusions, use 3 parameters flowrate setting (50 ml / h; 100 ml / h; 200 ml / h) and the data collection repeated for 5 times, with 3 minutes time for each parameter. The results of data collection will be tested using the normality test and difference test. Infusion Pump was calibrated first by using the Infusion Device Analyzer to check the condition of the tool. Based on the results of the T-test where the significant value is greater than 0.05, which means that the null hypothesis is accepted while the alternative hypothesis is rejected
Fetal Doppler Simulator Based on Arduino Alfina Nadhirotussolikah; Andjar Pudji; Muhammad Ridha Mak'ruf
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.6

Abstract

Heart rate of the fetal is the main indicator of the fetal life in the womb. Monitoring fetal heart rate can’t be done, so a tool is needed to monitoring fetal heart rate. Fetal heart rate can be monitored with fetal doppler. To test the accuracy of Fetal Doppler, a calibration is needed with the Fetal Doppler Simulator. This tool will simulate the fetal heart rate with a BPM value that can be adjusted according to the settings on the device. This module using Arduino as the brain system. On the module there is a selection of BPM from 60 to 240 BPM with an increase of 30 BPM displayed on 2x16 character LCDs. Based on BPM measurement 6 times using Fetal Doppler, the measurement error in a BPM of 60 to BPM 210 is 0%, while at BPM 240 an error is 0.2%. This module has been compared with the standard devices (Fetal Simulator Brand Fluke Biomedical Ps320), the results of the comparison modules with the comparison tool has the same error value in 240 BPM is 0.2% and in BPM 210 there is a difference in the result of module Fetal Doppler reading of 210 BPM while in the comparison tool is 209 BPM. Of the measurement data and analysis, it can be concluded that the tool can work and the tool has the same accuracy as the standard device.
Effect of Temperature on pH Meter Based on Arduino Uno With Internal Calibration lilia wati dewi pratami; Her Gumiwang Ariswati; Dyah Titisari
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.5

Abstract

pH Meter is a device used to express the level of acidity or basicity possessed by a substance or solution. Normal pH has a value of 7 while the pH value> 7 indicates that the substance has alkaline properties while the pH value <7 indicates acidic properties. pH 0 shows a high degree of acidity, and pH 14 shows the highest degree of alkalinity. pH Meter reads the pH and temperature values ​​in a sample. The author uses glass electrodes as a pH sensor, DS18B20 as a temperature sensor and LCD to make pH and temperature values. This module is equipped with an internal calibration that is used to set the module to read the pH value properly and correctly using a pH buffer and equipped with internal storage and this module facilitates battery usage. Based on pH measurements on the module the error value in buffer 4 calibration is 5.39%, in buffer 7 is 1.76%, in buffer 10 is 1.04%. The highest error value in the measurement sample is 3.54% and the lowest error value is 0.03%. The temperature of the sample is very influential on the reading of the pH value because the higher the temperature the pH value also increases even though it is not so significant.
Calculation Of Fetal Weight Estimation Displayed With TFT LCD Nadhia Regitasari; M. Ridha Mak'ruf; Endang Dian Setioningsih
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.4

Abstract

Fetal weight estimation during pregnancy is one of the beneficial ways to solve morbidity and death during labor problem. Manually, the fundal height is measured from the edge of the pubic symphysis to the top of the uterine fundus by following the arch of the uterus, using a measuring tape. The purpose of this study is to develop an easy way to count fetal weight estimation so midwives don’t have to count manually. The calculation of fetal weight estimation tool uses a variable resistor (potentiometer) as a sensor to measure the fundal height. Then it will be processed in microcontroller. The measurement results are fundal height and estimation fetal weight that will be displayed on the TFT LCD. Based on the results of measuring the fundus uterine height as much as 6 times against the measuring tool (ruler), there is no error in the device so it can be concluded that this tool can be used according to its function. This calculation of fetal weight estimation tool is portable and easy to use to help midwives count the fetal weight estimation quickly.
Design of Respiration Rate Meter Using Flexible Sensor Sarah Aghnia Miyagi; Muhammad Ridha Mak’ruf; Endang Dian Setioningsih; Tark Das
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.3

Abstract

Respiration rate is an important physiological parameter that helps to provide important information about the patient's health status, especially from the human respiratory system. So it is necessary to measure the human respiratory rate by calculating the number of respiratory frequencies within 1 minute. The respiratory rate meter is a tool used to calculate the respiratory rate by counting the number of breaths for 1 minute. The author makes a tool to detect human respiratory rate by using a sensor that detects the ascend and descend of the chest cavity based on a microcontroller so that the operator can measure the breathing rate more practically and accurately. Component tool contains analog signal conditioning circuit and microcontroller circuit accompanied by display in the form of LCD TFT. The results of measurement data on 10 respondents obtained an average error value, namely the position of the right chest cavity 6.6%, middle chest cavity 7.92%, and left chest cavity 6.85%. This value is still below the error tolerance limit of 10%. It can be concluded that to obtain the best measurement results, the sensor is placed in the position of the right chest cavity.
Peak Flow Meter Equipped with Inspection Results Indicator Nadiya Garnis Sallyfan; Endro Yulianto; Torib Hamzah
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v2i1.2

Abstract

Peak Flow Meter (PFM) is a tool to measure the Peak Flow of Air Expiration in the road (PFR) or commonly referred to as Peak Expiration Flow (PEF) and to connect asthma. The value of PEF can help a number of factors in age, respiratory muscle strength, height and gender. Airway measurements are used to measure patients suffering from asthma. This peak flow meter tool works based on the air pressure produced from the patient's puff using the MPX5100GP pressure sensor in the range of 0 to 100 kPa and the voltage output is 0.2 to 4.7 VDC to increase wind pressure in the patient. From the pressure converted to voltage and enter the 0 from the Arduino nano minimum system circuit to be processed into analog data and then put into units of liters / second, the value of the flow meter is sent and replaced to a PC with the Delphi7 application. The measurement results of PEF values at peak flow meters have an error value of less than 5% This peak flow meter tool also has a consideration value of 0.095475 so that this tool can be said to be very certain to be used as asthma. Then it can be concluded that the peak flow meter is feasible and meets the specified requirements

Page 1 of 1 | Total Record : 6

 1 

Filter by Year

2020 2020


Reset
Filter By Issues
All Issue Vol 8 No 1 (2026): January Vol 7 No 4 (2025): October Vol 7 No 3 (2025): July Vol 7 No 2 (2025): April Vol 7 No 1 (2025): January Vol 6 No 4 (2024): October Vol 6 No 3 (2024): July Vol 6 No 2 (2024): April Vol 6 No 1 (2024): January Vol 5 No 4 (2023): October Vol 5 No 3 (2023): July Vol 5 No 2 (2023): April Vol 5 No 1 (2023): January Vol 4 No 4 (2022): October Vol 4 No 3 (2022): July Vol 4 No 2 (2022): April Vol 4 No 1 (2022): January Vol 3 No 3 (2021): October Vol 3 No 2 (2021): July Vol 3 No 1 (2021): January Vol 2 No 3 (2020): October Vol 2 No 2 (2020): July Vol 2 No 1 (2020): January Vol 1 No 2 (2019): October Vol 1 No 1 (2019): July More Issue