cover
Contact Name
Habibi
Contact Email
habibi@unhas.ac.id
Phone
+6281225372161
Journal Mail Official
zonalaut@unhas.ac.id
Editorial Address
Gdg.Naval A Lt.1 Kampus Teknik Unhas Gowa, Jl. Poros Malino, Bontomarannu, Gowa
Location
Kota makassar,
Sulawesi selatan
INDONESIA
Zona Laut : Jurnal Inovasi Sains dan Teknologi Kelautan
Published by Universitas Hasanuddin
ISSN : 27472124     EISSN : 27215717     DOI : 10.20956
Dalam Pengembangan dan pengolahan SDA maritim memerlukan kerjasama multidisiplin ilmu, dimana kesemua disiplin ilmu tersebut berperan besar dalam menjadikan Indonesia sebagai poros maritim dunia. Oleh karena itu diperlukan inovasi dan sinergi untuk menghasilkan riset tentang teknologi kelautan oleh perguruan tinggi, lembaga-lembaga penelitian dan industri dapat memberikan kontribusi terhadap issue tersebut. Tujuan Zona Laut adalah sebagai wadah menyalurkan pemikiran, ide-ide cemerlang dan konstruktif komprehensif sehingga menjadi bagian usulan-usulan solusi bagi kemajuan pembangunan Sumber Daya Kelautan Indonesia. Topik-topik yang dapat diterbitkan Zona Laut ini adalah: 1. Teknologi dan Rekayasa Bangunan Lepas Pantai 2. Desain Produk Bangunan Perikanan dan Kelautan 3. Manajemen Transportasi Laut dan Aplikasi Teknologi Pelayaran 4. Energi Kelautan Terbarukan 5. Sistem dan Pengendalian Kelautan 6. Material Maju kelautan 7. Rekayasa dan Manajemen Kepelabuhanan serta Pengembangan Sumber Daya Pesisir 8. Oseanografi dan Keteknikpantaian 9. Kebencanaan Pantai dan Lingkungan Laut Jurnal ini diterbitkan oleh Departemen Teknik Kelautan, Fakultas Teknik, Universitas Hasanuddin pada bulan Maret, Juli dan Nopember setiap tahun. Naskah yang telah disetujui untuk diterbitkan telah ditinjau oleh pengulas dan abstrak bebas untuk diunduh melalui situs web kami.
Articles 11 Documents
Search results for , issue "Volume 5, Number 2, July 2024 Edition" : 11 Documents clear
Fatigue Life Analysis of Mooring Cleats on The N219A Aircraft Floater Based on Numerical Simulation Yulfani, Rosi Dwi; Rosyid, Daniel M.; Nugroho, Wibowo Harso; Priohutomo, Kusnindar; Sugiarto, Moh. Muria Armansyah; Arianti, Erdina
Zona Laut : Jurnal Inovasi Sains Dan Teknologi Kelautan Volume 5, Number 2, July 2024 Edition
Publisher : Departemen Teknik Kelautan Universitas Hasanuddin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62012/zl.v5i2.42798

Abstract

One of the procedures for rescuing a seaplane after an operational is to secure it, namely by mooring at an available port or mooring at a mooring buoy. This mooring buoy is considered a vehicle necessary for securing seaplanes in coastal conditions where it is not yet possible to build infrastructure in the form of an amphiport. To overcome this problem, seaplanes need to add a mooring cleat at the end of the bow of each float, which attaches the rope to the mooring buoy itself. So, it is necessary to study the strength of the mooring cleat itself when withstanding environmental loads. This study was carried out by modelling the mooring cleat using the finite element method to determine where the most significant stresses occur in the mooring cleat structure. Mooring cleats are modelled on deck thickness with varying thicknesses of 20mm and 40mm. The stress that occurred in the mooring cleat structure is then calculated using the Palmgren-Miner rule to determine the fatigue life of the mooring cleat for each variation. It was found that the largest von Misses stress experienced by the structure using 7075-T6 aluminium material was 147.87 MPa, which occurred in the mooring cleat, which was located on the 20mm deck thickness variation at the portside. Meanwhile, this variation's most extended fatigue life calculation occurred for the 40mm deck thickness variation on the portside with 514.43 years.

Page 2 of 2 | Total Record : 11