cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
ganendra@batan.go.id
Editorial Address
Jl. Babarsari Kotak Pos 6101 ykbb, Yogyakarta 55281
Location
Kota adm. jakarta selatan,
Dki jakarta
INDONESIA
Ganendra: Majalah IPTEK Nuklir
ISSN : 14106957     EISSN : 25035029     DOI : https://doi.org/10.17146/gnd
Core Subject : Science, Education,
Jurnal Iptek Nuklir Ganendra merupakan jurnal ilmiah hasil litbang dalam bidang iptek nuklir, diterbitkan oleh Pusat Teknologi Akselerator dan Proses Bahan (PTAPB) - BATAN Yogyakarta. Frekuensi terbit dua kali setahun setiap bulan Januari dan Juli.
Arjuna Subject : -
Articles 5 Documents
Search results for , issue "Volume 19 Nomor 2 Juli 2016" : 5 Documents clear
OPTIMATION OF DECY-13 CYCLOTRON MAGNET MAPPING SYSTEM Taufik Taufik; Kurnia Wibowo; Frida Iswining Dyah; Suprapto Suprapto
GANENDRA Majalah IPTEK Nuklir Volume 19 Nomor 2 Juli 2016
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (707.879 KB) | DOI: 10.17146/gnd.2016.19.2.2865

Abstract

OPTIMATION OF DECY-13 CYCLOTRON MAGNET MAPPING SYSTEM. A cyclotron magnet serves to deflect the particle beam so that the beam trajectory is circular and also serves to focus the beam. The magnetic flux density of a cyclotron magnet must satisfy the isochronous field. The magnetic field distribution need to be measured in order to know that the magnetic flux density have fulfilled the isochronous field, therefore a mapping system is needed to obtain the magnetic field distribution data. The design and construction of mechanical system of magnetic field mapping has been carried out in 2013 using fly mode algorithm, but the test results is not accurate yet. Therefore it is necessary to  optimize of the magnetic field mapping system.  The aim of this optimation is to improve the accuracy of step position and the precission of magnetic field measurement of the mapping system of DECY-13 cyclotron magnet.  The research was done by changing the mapping methods that previously based on the fly mode with the step mode. In the step mode, the magnetic field data will be taken when the probe has been completely stopped at the specified position. The magnet mapping system has been optimized with 99.89% of the average step position accuracion.  The mapping system has to start at minimum of 2 hours after the MPS is turned on, in order to get 3.53 gauss of the precision of magnetic field measurement. Although the magnetic field measurement of 1st sensor and 2nd sensor have 6.3 gauss of measurement maximum different but the two sensors have the same pattern of magnetic field average. The mapping result from one of 2 sensors can be used to calculate magnetic field parameter if the magnetic field is symmetric.
ANALISA PERMUKAAN MATERIAL ALUMINIUM PADUAN (AlSiCu) HASIL NITRIDASI ION Suprapto Suprapto; Tjipto Sujitno; Taufik Taufik
GANENDRA Majalah IPTEK Nuklir Volume 19 Nomor 2 Juli 2016
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (760.658 KB) | DOI: 10.17146/gnd.2016.19.2.2999

Abstract

ABSTRAK ANALISA PERMUKAAN MATERIAL ALUMINIUM PADUAN (AlSiCu) HASIL NITRIDASI ION. Paduan aluminium (AlSiCu) merupakan material yang banyak digunakan untuk komponen mesin misalnya piston dan pully karena ringan dengan kekuatan spesifiknya yang tinggi.  Kelemahan utama dari paduan ini adalah kekerasan dan kehandalan aus yang rendah.  Untuk mengatasi masalah tersebut dilakukan perlakuan permukaan dengan teknik nitridasi ion untuk meningkatkan kekerasan permukaan maupun kehandalan ausnya.  Proses nitridasi ion ini dilakukan dengan berbagai variasi parameter meliputi: lamanya proses, tekanan dan temperatur.  Untuk mengetahui hasil proses nitridasi dilakukan analisa struktur mikro dan komposisi unsur, uji keras maupun uji aus baik untuk sampel awal maupun yang telah di nitridasi.  Dari hasil pengujian diperoleh bahwa kondisi optimum dari parameter proses dicapai pada lamanya proses 3 jam, tekanan 1,2 mbar dan temperatur 150 °C.  Berdasarkan analisa struktur mikro dan unsur untuk hasil nitridasi pada kondisi optimun diperoleh perubahan struktur permukaan akibat terbentuknya senyawa AlN dan Al2O3 dan terdeksi kandungan unsur nitrogen serta oksigen masing masing sebesar 3.95 %/berat dan 29.93%/berat.  Untuk uji keras dan aus diperoleh kekerasan permukaan meningkat dari 60,24 VHN untuk material awal menjadi 120,88 V setelan dinitridasi yaitu 2,01 kalinya, keausan turun (ketahan aus meningkat) dari 4,1 × 10-5 mm2/kg menjadi 3 × 10-6 mm2/kg atau terjadi peningkatan ketahan aus sebesar 13.67 kalinya.  Dari data tersebut dapat disimpulkan bahwa peningkatan kekerasan maupun ketahanan aus  kemungkinan besar disebabkan oleh terbentuknya senyawa AlN maupun Al2O3.  Dari data tersebut juga dapat disimpulkan bahwa dengan meningkatnya kekerasan maupun ketahan aus maka umur pemakaiaan komponen juga meningkat (umur pemakaian lebih lama)
ANALISIS PENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM Syarip, Khoirul Anam, Dwi Priyantoro
GANENDRA Majalah IPTEK Nuklir Volume 19 Nomor 2 Juli 2016
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1023.534 KB) | DOI: 10.17146/gnd.2016.19.2.3008

Abstract

ANALISISPENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM POST REACTOR SCRAM CONTROL RODS POSITION ADJUSTMENT ANALYSIS FOR THE INDONESIAN EXPERIMENTAL POWER REACTOR CONCEPT. ABSTRAK ANALISIS PENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM. Telah dilakukan analisis simulasi pengaturan posisi batang-batang kendali untuk melanjutkan operasi reaktor daya eksperimental (RDE) paska scram setelah beroperasi pada periode waktu tertentu. Pengendalian reaktivitas pada reaktor RDE yang akan dibangun di Indonesia dengan rujukan high temperature gas reactor (HTR) 10 MWt, dilakukan dengan 10  pasang batang-batang kendali atau control rod (CR). Apabila terrjadi kondisi abnormal maka CR secara otomatis akan jatuh tersisip ke dalam reflektor  reaktor sehingga reaktor scram dan berada pada kondisi subkritis. Untuk melanjutkan operasi reaktor pasca scram diperlukan analisis terkait pengaruh reaktivitas negatif dari Xenon dan suhu. Pada makalah ini disajikan hasil simulasi yang dilakukan untuk penentuan posisi CR paling optimum untuk melanjutkan operasi reaktor, menggunakan simulator PCTRAN-HTR. Simulasi dilakukan pada variasi 70%, 85% dan 100% dari tingkat daya penuh dan dengan variasi waktu operasi 50 s, 10.000 s, dan 20.000 s di mana setelah reaktor beroperasi pada tingkat-tingkat daya dan waktu operasi tersebut reaktor mengalami scram. Untuk melanjutkan operasi lagi maka CR harus dinaikkan lagi dan diatur ke posisi tertentu sampai   reaktor mencapai kondisi kritis lagi pada tingkat daya nominal tersebut. Hasil yang telah diperoleh menunjukkan bahwa dengan posisi CR naik 52 % sudah bisa menghasilkan kondisi kritis dan mampu mengatasi reaktivitas negatif peracunan xenon maupun suhu. Kata kunci: RDE, HTR, operasi reaktor, batang kendali, reaktivitas, scram ABSTRACT POST REACTOR SCRAM CONTROL RODS POSITION ADJUSTMENT ANALYSIS FOR THE INDONESIAN EXPERIMENTAL POWER REACTOR CONCEPT. Analytical study using PC-based simulator has been carried out on control rods position adjustment of the Indonesian experimental power reactor concept or reaktor daya ekperimental (RDE) in a post reactor scram to continue operation after a certain operation period. Reactivity control of the RDE uses 10 pairs of control rods (CRs), which is based on that applied in the high temperature gas reactor (HTR) 10 MW(t). If an abnormal operating condition occurs, these control rods automatically dropped to the reflector that bring the reactor into a scram and subcritical condition. To continue reactor operation after a period of time, the CRs should be withdrawn to achieve recriticality. Prior to any CRs withdrawal, an analysis of negative reactivity effects of Xenon (poissoning) and fuel temperature coefficient should be done. Simulations using PCTRAN-HTR simulator to determine the optimum CRs positions in achieving reactor criticality for continuation of reactor operation is presented in this paper. The simulations were conducted by varying the reactor power levels at 70%, 85% and 100% of full power, respectively. The reactor operation time was varied at 50s, 10000s, and 20000 s prior to the reactor scram. Adjustment of CRs position should be done to continue reactor operation at those nominal power levels by withdrawing the CRs to the proper positions. The simulation results show that recriticality can be achieverd by whitdrawing the CRs 52% of farther and the negative reactivity from xenon poisoning and temperature could be overcome. Keywords : RDE, HTR, reactor operation, control rod, reactivity, scram.
PEMETAAN LAJU DOSIS GAMMA DI GREEN HOUSE DENGAN METODE MONTE CARLO PROGRAM PHITS Rasito Tursinah; Putu Sukmabuana
GANENDRA Majalah IPTEK Nuklir Volume 19 Nomor 2 Juli 2016
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (865.743 KB) | DOI: 10.17146/gnd.2016.19.2.3032

Abstract

Pemetaan laju dosis gamma di green house dilakukan dalam rangka proteksi dan keselamatan radiasi personil. Laju dosis gamma dihasilkan dari adanya penggunaan radionuklida 134Cs dan 60Co dalam kegiatan penelitian faktor transfer dan remediasi. Di dalam ruang green house terdapat 12 buah kotak ukuran 1 x 1 x 0,5 m3 yang diisi tanah andosol dengan tebal tanah 20 cm dan 2 buah bak oval panjang 1,7 m, lebar 0,5 m dan tinggi 0,5 m yang diisi air. Dari 12 kotak tersebut 6 kotak diisi tanah yang dikontaminasi radionuklida, sedangkan dari 2 bak oval 1 bak diisi air yang dikontaminasi. Radionuklida kontaminan yang digunakan pada penelitian pertama adalah 134Cs dan pada penelitian kedua adalah 60Co dengan aktivitas masing-masing 2 MBq. Dengan menggunakan program komputer PHITS yang berbasis perhitungan Monte Carlo laju dosis gamma di dalam dan di luar ruang green house dihitung. Berdasarkan hasil perhitungan diperoleh laju dosis gamma adalah 0,1 µSv/jam – 1 µSv/jam baik untuk sumber 134Cs ataupun 60Co. Nilai laju dosis gamma tersebut terkategori aman karena masih di bawah nilai batas yang diijinkan untuk pekerja maupun publik.
STUDI MODEL BENCHMARK MCNP6 DALAM PERHITUNGAN REAKTIVITAS BATANG KENDALI HTR-10 Zuhair, Suwoto, Putranto Ilham Yazid, Jupiter S.Pane
GANENDRA Majalah IPTEK Nuklir Volume 19 Nomor 2 Juli 2016
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (534.499 KB) | DOI: 10.17146/gnd.2016.19.2.2880

Abstract

ABSTRAK STUDI MODEL BENCHMARK MCNP6 DALAM PERHITUNGAN REAKTIVITAS BATANG KENDALI HTR-10. Dalam operasi reaktor nuklir, sistem batang kendali memainkan peranan yang sangat penting karena didesain untuk mengendalikan reaktivitas teras dan memadamkan reaktor. Nilai reaktivitas batang kendali harus diprediksi secara akurat melalui eksperimen dan perhitungan. Makalah ini mendiskusikan model Benchmark dalam perhitungan reaktivitas batang kendali reaktor HTR-10. Perhitungan dikerjakan dengan program transport Monte Carlo MCNP6 dan pustaka data nuklir energi kontinu ENDF/B-VII. Hasil perhitungan memperlihatkan prediksi MCNP6 memiliki kesesuaian yang cukup baik dengan pendekatan difusi maupun model Monte Carlo yang diestimasi China untuk reaktivitas sepuluh batang kendali fully in di teras penuh (problema Benchmark B3.1 dan  B4.1). Simulasi MCNP6 memperlihatkan hasil yang kurang menguntungkan dalam kasus reaktivitas satu batang kendali fully in di teras penuh (problema Bechnmark B3.2), namun sebaliknya mendemonstrasikan akurasinya yang paling tinggi di teras inisial (problema Benchmark B4.2). Hasil-hasil ini menyimpulkan bahwa model MCNP6 yang digunakan dalam perhitungan reaktivitas batang kendali HTR-10 dapat diaplikasikan untuk analisis fisika teras reaktor pebble bed lainnya.

Page 1 of 1 | Total Record : 5