Ketut Sumada
Department of Chemical Engineering, UPN “Veteran” Jawa Timur, Surabaya, Indonesia

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

Synthesis of CaO-MgO Catalyst from Dolomite via Dissolution and Precipitation Processes Amelia Salsabilla Cantika; Moh. Rizal Febriyanto; Ketut Sumada; Ardika Nurmawati; Caecilia Pujiastuti; Erwan Adi Saputro
AJARCDE (Asian Journal of Applied Research for Community Development and Empowerment) Vol. 10 No. 3 (2026)
Publisher : Asia Pacific Network for Sustainable Agriculture, Food and Energy (SAFE-Network)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29165/ajarcde.v10i3.1155

Abstract

Dolomite is an abundant carbonate mineral containing calcium and magnesium compounds that can serve as a precursor for heterogeneous catalyst synthesis. This study investigated the effects of NaOH volume (90-170 mL) and dehydration temperature (300-700°C) on the synthesis and physicochemical properties of calcium-magnesium-based materials prepared via a dissolution-precipitation method, which was selected over conventional calcination because it enables systematic control of the precipitation process through adjustment of the NaOH volume. XRF analysis showed that the raw dolomite contained 88.81% CaO and 9.70% MgO. Two-way ANOVA confirmed that NaOH volume, dehydration temperature, and their interaction significantly affected catalyst basicity (p < 0.001), with the highest value (1.960 mmol/g) obtained at 150 mL NaOH and 500°C. SEM analysis of catalysts with low, medium, and high basicity revealed increasingly well-developed and uniformly distributed particle morphologies toward the optimum condition, while EDX identified calcium, magnesium, and oxygen as the predominant elements. BET characterization of the material exhibiting the highest basicity showed a specific surface area of 126.585 m2/g and an average pore diameter of 21.545 nm. These findings demonstrate that NaOH volume and dehydration temperature play important roles in tailoring the physicochemical properties of the catalyst materials. The optimized synthesis condition provides useful guidance for preparing calcium-magnesium-based materials with high basicity and favorable textural properties and serves as a foundation for future phase identification and catalytic performance evaluation. Contribution to Sustainable Development Goals (SDGs):SDG 9: Industry, Innovation and InfrastructureSDG 12: Responsible Consumption and ProductionSDG 13: Climate Action
Synthesis and Characterization of Rigid Polyurethane Foam from Palm Oil-Derived Oleic Acid Polyol via Open Molding Process Naufal Dzikri Musyaffa; Aldhila Ardalia Nella Angga; Suprihatin Suprihatin; Ketut Sumada; Sani Sani
AJARCDE (Asian Journal of Applied Research for Community Development and Empowerment) Vol. 10 No. 3 (2026)
Publisher : Asia Pacific Network for Sustainable Agriculture, Food and Energy (SAFE-Network)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29165/ajarcde.v10i3.1398

Abstract

Oleic acid derived from palm oil contains a carbon–carbon double bond that can be converted into a polyol through epoxidation and hydroxylation, making it a promising renewable feedstock for rigid polyurethane foam. Polyurethane was synthesized by an open molding process, varying toluene diisocyanate (TDI) and polyethylene glycol (PEG-400) volumes from 10 to 30 mL each. The resulting polyol was a clear, pale-yellow liquid with a density of 0.9363 g/cm³, a viscosity of 14.03 cSt, a pH of 5.22, an acid value of 174.8 mg KOH/g and a hydroxyl value of 180.7 mg KOH/g. Increasing TDI volume decreased foam density due to exothermic CO? generation but increased compressive strength through higher crosslink density, whereas increasing PEG-400 linearly increased density but lowered compressive strength at high TDI levels, as PEG-400 acts as a soft-segment former. The optimum formulation, satisfying ASTM F1839 Grade 5, was Polyol : TDI : PEG-400 = 10 : 30 : 15 mL, giving a density of 0.0743 g/cm³ and a compressive strength of 0.7089 MPa. SEM showed a predominantly closed-cell structure, and FTIR confirmed urethane-bond formation (N–H, C=O, C–O). These results show that palm-oil-derived oleic acid is a feasible renewable feedstock for bio-based rigid polyurethane foam, supporting SDG 9 (Industry, Innovation and Infrastructure), SDG 12 (Responsible Consumption and Production) and SDG 13 (Climate Action). Contribution to Sustainable Development Goals (SDGs):SDG 9  : Industry, Innovation, and InfrastructureSDG 12: Responsible Consumption and ProductionSDG 13: Climate Action