Claim Missing Document
Check
Articles

Found 3 Documents
Search

Optimasi parameter resistance spot welding pada pengabungan baja electro-galvanized menggunakan metode Taguchi Sukarman, S.; Abdulah, A.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 11, No 1 (2021): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (510.199 KB) | DOI: 10.29303/dtm.v11i1.372

Abstract

The present study features analytical and experimental results of optimizing resistance spot welding performed using a pneumatic (electrode) force system (PFS). This optimization was carried out to incorporate the galvanized steel sheet material SECC-AF (JIS G 3313) and SPCC-SD (JIS 3141) sheet plate coated with zinc with a thickness of about 2.5 microns. The zinc coating on the metal surface causes its weldability to decrease. This study aims to obtain the highest tensile shear strength test results from the combination of the specified resistance spot welding parameters. The research method used the Taguchi method using four variables and a combination of experimental tingkats. This study's experimental tingkat is two tingkats in the first parameter and three tingkats in other parameters. Taguchi optimization results show that the highest tensile shear strength test obtained is 5049.64 N. This was achieved at 22 cycles of squeeze time, 25 kA of welding current, and 0,6-second welding-time, and 12 cycles of holding-time. The S / N ratio analysis found that the welding time had the most significant effect, followed by welding current, holding time, and squeeze time. The delta S / N ratio values were 0.62, 0,41, 0.34 and 0.07, respectively.
The Modelling and Analysis of iPWR-Type SMR Core Dynamics: Control Rods, Reactivity Feedback, and Thermal-Hydraulic Effects Septawijaya, G.; Sukarman, S.; Bakhri, S.; Subekti, M.
Atom Indonesia Vol 50, No 3 (2024): DECEMBER 2024
Publisher : National Research and Innovation Agency

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/aij.2024.1414

Abstract

Development plans for Nuclear Power Plants (NPPs) in Indonesia have been widely discussed. One of the planned NPP types is the Small Modular Reactor (SMR). Human resource readiness is an essential aspect to be considered before constructing an NPP. Simulators capable of illustrating core dynamics can be used to educate the public about the processes within a nuclear reactor. Core modeling is a key component in developing an NPP simulator. The neutronic behavior of the reactor core is modeled using point kinetics equations, while the thermal-hydraulic aspect uses Mann’s model. The results indicate that the modeled core can operate up to 160 MWt and other operating parameters at maximum power align well with the SMR reactor design certification data.
Optimasi parameter resistance spot welding pada pengabungan baja electro-galvanized menggunakan metode Taguchi Sukarman, S.; Abdulah, A.
Dinamika Teknik Mesin Vol 11, No 1 (2021): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29303/dtm.v11i1.372

Abstract

The present study features analytical and experimental results of optimizing resistance spot welding performed using a pneumatic (electrode) force system (PFS). This optimization was carried out to incorporate the galvanized steel sheet material SECC-AF (JIS G 3313) and SPCC-SD (JIS 3141) sheet plate coated with zinc with a thickness of about 2.5 microns. The zinc coating on the metal surface causes its weldability to decrease. This study aims to obtain the highest tensile shear strength test results from the combination of the specified resistance spot welding parameters. The research method used the Taguchi method using four variables and a combination of experimental tingkats. This study's experimental tingkat is two tingkats in the first parameter and three tingkats in other parameters. Taguchi optimization results show that the highest tensile shear strength test obtained is 5049.64 N. This was achieved at 22 cycles of squeeze time, 25 kA of welding current, and 0,6-second welding-time, and 12 cycles of holding-time. The S / N ratio analysis found that the welding time had the most significant effect, followed by welding current, holding time, and squeeze time. The delta S / N ratio values were 0.62, 0,41, 0.34 and 0.07, respectively.