Rizqi Andry Ardiansyah
Peneliti Pusat Penelitian Dan Pengembangan Sistem Dan Kebijakan Kesehatan Sistem Dan Kebijakan Kesehatan, Badan Litbangkes, Depkes R.I.

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

Rotational Speed Control of Brushless Dc Motor Using Genetic Algorithm Optimized PD Controller Ardiansyah, Rizqi Andry; Yazid, Edwar
Jurnal Elektronika dan Telekomunikasi Vol 18, No 2 (2018)
Publisher : Indonesian Institute of Sciences

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/jet.v18.75-80

Abstract

Controlling the rotational speed of brushless DC (BLDC) motor is an essential task to improve the transient and the steady state performances under loaded condition. Rotational speed control of BLDC motor using genetic algorithm optimized proportional-derivative (PD) controller to form what the so-called the genetic algorithm-PD (GA-PD) controller is proposed in this paper. Control system is realized in a microcontroller namely a 16MHz Atmega2560 with an absolute encoder as a position sensor. The effectiveness of the GA-PD controller is tested under constant and varying step functions with the Ziegler-Nichols-PD (ZN-PD) controller as a benchmark. Experimental results show that the GA-PD controller has slower speed than the ZN-PD controller, but the latter has overshoot and small oscillations during its steady state condition as a consequent of having a fast rise time.
DC Brushless Motor Control Design and Preliminary Testing for Independent 4-Wheel Drive Rev-11 Robotic Platform Saputra, Roni Permana; Ardiansyah, Rizqi Andry; Mirdanies, Midriem; Santoso, Arif; Nugraha, Aditya Sukma; Muqorobin, Anwar; Saputra, Hendri Maja; Susanti, Vita; Rijanto, Estiko
Journal of Mechatronics, Electrical Power and Vehicular Technology Vol 2, No 2 (2011)
Publisher : Research Centre for Electrical Power and Mechatronics, Indonesian Istitutes of Sciences

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (714.52 KB) | DOI: 10.14203/j.mev.2011.v2.85-94

Abstract

This paper discusses the design of control system for brushless DC motor using microcontroller ATMega 16 that will be applied to an independent 4-wheel drive Mobile Robot LIPI version 2 (REV-11). The control system consists of two parts which are brushless DC motor control module and supervisory control module that coordinates the desired command to the motor control module. To control the REV-11 platform, supervisory control transmit the reference data of speed and direction of motor to control the speed and direction of each actuator on the platform REV-11. From the test results it is concluded that the designed control system work properly to coordinate and control the speed and direction of motion of the actuator motor REV-11 platform. 
Rancang Bangun Sistem Kontrol Mekanisme Pelacakan Matahari Beserta Fasilitas Telekontrol Hemat Energi Mirdanies, Midriem; Ardiansyah, Rizqi Andry; Saputra, Hendri Maja; Nugraha, Aditya Sukma; Rijanto, Estiko; Santoso, Adi
Journal of Mechatronics, Electrical Power and Vehicular Technology Vol 2, No 1 (2011)
Publisher : Research Centre for Electrical Power and Mechatronics, Indonesian Istitutes of Sciences

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (678.862 KB) | DOI: 10.14203/j.mev.2011.v2.31-40

Abstract

Solar energy produced by concentrated solar heat collector panels requires tracking mechanisms for a more optimal direction. This paper presents the design and construction of a low energy solar tracking control system with telecontrol facilities. To accelerate the movement of the panel in always adjusting itself to the direction of the sun, a combination of the timer and light sensor was used. In this control system, the reference signal is taken from two pieces of light sensors while the feedback is taken from the position and temperature sensors. The program has been developed using C language and was implemented on the microcontroller ATMega8535 as the brain of the system. Telecontrol facilities for monitoring the data to a computer uses transceiver modules via RS-232 connection. A DC motor having power capacity of 0.74 watts was used and was clutched with 1:7,300 gearbox ratio. Experiments on light sensor characteristics and simulated movement of the panel were carried out. From the light sensor experiment it can be concluded that the sensor produces 0-4 volt output signal when bright 3.3-3.9 volts, when cloudy and 1.5-3.3 volts when sunny. From the simulation of panel movement, it is known that the solar tracking control system moves the panel and tracks the direction of the sun movement.Â