Juandra Hartono
Politeknik Pekerjaan Umum

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

Evaluasi Keutuhan Borepile Metode Crosshole Sonic Logging (CSL) Pembangunan Jembatan Pulau Balang II Juandra Hartono
Jurnal Aplikasi Teknik Sipil Vol 19, No 4 (2021)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1018.904 KB) | DOI: 10.12962/j2579-891X.v19i4.9745

Abstract

The problem that occurs in the Balang II Island Bridge construction project in East Kalimantan Province is the blockage of concrete flowing through the tremi pipe when casting the borepile foundation at sea. A considerable distance from the initial location of the tremi pipe (on land) to the endpoint of casting requires a fairly long tremi pipe. This blockage causes the concrete to flow imperfectly. There are many speculations about the cause of this problem, including leaks in the tremi pipe and the uniformity of the concrete mix. Based on these problems to prevent the failure of the foundation structure, an integrity test will be carried out on non-destructive piles. The integrity test to be carried out is in the form of a Crosshole Sonic Logging Test (CSL). The results of the CSL test on pylon P1 show that of the 17 borepile piles tested 2 piles have abnormalities, namely the P1-64 pile with the P/D category on the whole cross-section and the P1-52 P/F category on some sections (± 40%). Overall it can be concluded that the integrity of the drill pile on pylon P1 is still quite safe.
ANALISA KORELASI ANTARA FREKUENSI DENGAN BENTANG JEMBATAN BERDASARKAN UJI DINAMIK Hinawan T. Santoso; Laely F. Hidayatiningrum; Adityo B. Utomo; Juandra Hartono; Masrianto -
Jurnal Jalan-Jembatan Vol 38 No 1 (2021)
Publisher : Direktorat Bina Teknik Jalan dan Jembatan

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The population of bridges on National Road in 2020 has reached 21,054 units with a total length of 587,309 meters. About 10.5% of bridges have a service life of less than 10 years, 68.1% in the range of 10 - 50 years, and 5.3% more than 50 years. As the service life increases, the condition of the bridge will decrease. This bridge condition is obtained from the results of a detailed inspection using the visual method. The accuracy of this method is highly dependent on the objectivity, ability, and experience of the bridge inspector. The large population of bridges, variations in service life and conditions, and limited experienced inspectors are obstacles in conventional bridge inspections. As an alternative, the dynamic test method can be used to check bridge conditions more quickly and accurately. The natural frequency of the dynamic test can be used to determine the integrity condition and the level of structural damage, by comparing it to the theoretical frequency. So far, the theoretical frequency is determined based on calculations or structural modeling. The limited data of technical specifications, design drawings, and as-built drawings are often an obstacle. Experience and special skills are also needed in calculating or modeling this structure. This study aims to analyze the correlation between frequency and bridge span based on bridge dynamic test data in Indonesia. The results obtained a mathematical formula, where the value of the frequency of the bridge is correlated to the span of the bridge with a correlation coefficient of -0.85. This coefficient shows that the relationship between the variables under consideration is very strong and inverse, where the longer the bridge span, the smaller the vertical frequency value of the bridge. Keywords: Dynamic Test, Bridge Span, Vertical Frequency, Correlation Analysis, Mathematical Formula
ALTERNATIF PERENCANAAN KOMPOSISI CAMPURAN BETON DENGAN GABUNGAN BAHAN TAMBAH KIMIA TIPE F DAN D AGAR WAKTU BUKA ACUAN DIPERCEPAT Juandra Hartono; Masrianto Masrianto; Indira L. Widuri; Bhima Dhanardono; Hinawan T. Santoso
Jurnal Jalan-Jembatan Vol 39 No 1 (2022)
Publisher : Direktorat Bina Teknik Jalan dan Jembatan

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The demand for an acceleration of project completion time is often an obstacle, especially in structural work which is a critical path. The length of time for concrete curing and formwork dismantling sometimes obstructs the progress of the project. The time required for casting, concrete curing and unloading of formwork in a long span bridge construction project is ± 14 days with a record that there are no obstacles in the field. Based on these problems, researchers are trying to provide an alternative solution through a compressive strength test with a variant of the concrete quality and the curing time using chemical additives type F and type D. The study aims to find the minimum concrete compressive strength, the curing time, and the effects of adding a chemical additive that refers to General Specifications Standard 2018 (70% of the designed concrete compressive strength). The variant of the concrete quality is 40 MPa, 50 Mpa, and 60 Mpa while the variant of the curing time is 1,2,3,7, and 28 days. Based on the study, the minimum concrete compressive strength for each concrete quality is 28,58 MPa, 36,85 MPa, and 46,25 MPa. The curing time needed for fc’ 40 MPa and fc’ 50 Mpa is 2 days while for fc’ 60 MPa is 3 days. The use of chemical additives also has an impact on increasing compressive strength. The maximum compressive strength value of 28 days is found in the variation of f'c 60 Mpa of 62.20 Mpa with additive content of type F dan D of 0.6% and 0,15% of the cement weight. Optimum compressive strength is achieved when the curing process is done using the soaking method. Key words: critical path, formwork, chemical additives, compressive strength, soaking method.
Stabilitas Lereng Timbunan Sta. 24+100 Jalan Akses Pulau Balang Menggunakan GeoStudio Juandra Hartono; Muhammad Saleh; Gitaning Primaswari
Jurnal Inovasi Konstruksi Vol 1, No 1 (2022): April
Publisher : Politeknik Pekerjaan Umum

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.56911/jik.v1i1.18

Abstract

Riset ini membahas tentang permasalahan lereng timbunan jalan akses pulau balang yang berlokasi di Penajam Paser Utara (PPU) Kalimantan Timur. Pada lereng timbunan area Sta. 24+100 sisi kanan terdapat longsoran lereng yang disebabkan adanya rembesan air masuk kebadan jalan, selain itu lapisan tanah dasar yang dinilai berupa tanah lunak (soft) dengan muka air tanah yang cukup tinggi berpotensi mengalami longsoran dan mengakibatkan penurunan tanah. Analisa dilakukan menggunakan software Geostudio. Dari hasil analisa lereng timbunan didapat hasil sebagai berikut, pada kondisi terkonsolidasi 1 tahun tanpa penanganan, kondisi lereng masih masuk dalam kriteria desain jangka panjang dengan nilai SF sebesar 1,546 sedangkan pada lereng dengan kondisi hujan didapatkan nilai SF sebesar 1,379. Kondisi ini tidak memenuhi kriteria desain SF jangka panjang (SF Jangka Panjang 1.5).  Pada kondisi lereng terkonsolidasi 1 tahun dengan penangan didapatkan nilai SF lereng sebesar 1,730 sedangkan pada lereng dengan kondisi hujan didapatkan nilai SF sebesar 1,574. Dari hasil analisa dapat diambil kesimpulan bahwa lereng pada kondisi terkonsolidasi 1 tahun dengan penanganan masih masuk dalam kriteria design jangka panjang. Rekomendasi penanganan lereng yang dipilih berupa penanganan dengan counterweight dan cerucuk dibawah timbunan