Claim Missing Document
Check
Articles

Found 20 Documents
Search

SISTEM KENDALI SUHU DAN PEMANTAUAN KELEMBABAN UDARA RUANGAN BERBASIS ARDUINO UNO DENGAN MENGGUNAKAN SENSOR DHT22 DAN PASSIVE INFRARED (PIR) Hannif Izzatul Islam; Nida Nabilah; Sofyan Sa'id Atsaurry; Dendy Handy Saputra; Gagat Mughni Pradipta; Ade Kurniawan; Heriyanto Syafutra; Irmansyah Irmansyah; Irzaman Irzaman
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (989.029 KB) | DOI: 10.21009/0305020123

Abstract

We have been successfully to create a Control System Temperature and Air Humidy Monitoring Room Based on Arduino Uno with DHT22 Sensor and Passive Infrared (PIR). DHT22 Sensor be used as a measurement of temperature and air humidity in the room and Passive Infrared Sensor as a tool of detection the movement of people in a room. In this experiment, carried out tests of the DHT22 sensor and digital thermometer with a type AZ-HT-02 to room temperature with a hot air given through a hairdryer for 3 minutes with a span of per 10 seconds. In this test, the obtained data is that the room temperature is which measured by DHT22 sensor have an average difference of 0.93 against digital thermometer (as a calibration). In this test also obtained DHT22 sensor more sensitive Rrelative Humidity (RH), this is caused when given the hot air, humidity measured more rapid adjustment and yet different with digital temperature was slow to adjust air humidity in the room. This device using an Arduino Uno board, a Liquid Crystal Display (LCD) module and Real Time Clock (RTC) as a display of the temperature and air humidity in real time. This device is connected to a fan that can stabilize the room temperature are considered less convient to do activities in the room. Keywords: Air Humidity, Arduino Uno, DHT22 Sensor, Passive Infrared Sensor, Temperature.
EKTRAKSI SILIKON DIOKSIDA DARI DAUN BAMBU Halimah Sa'diyah; Salamet Nurhimawan; Sigit Ahmad Fatoni; Irmansyah Irmansyah; Irzaman Irzaman
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 5 (2016): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2016
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (416.995 KB) | DOI: 10.21009/0305020303

Abstract

Silika extract has got from bamboo leaf by leaching with HCl 7% p.a. After bamboo leaf was burned, the charcoal was heated in the furnace with annealing rates of 0.9 and 1 °C/minute. The first temperature was room temperature, then increased to 400 °C with 2 hours arrested time. And last increased to 950 °C with 1 hour arrested time. The resulting ash was leached with HCl 7% p.a and its pH was neutralisted by aquabides. Then, the neutral ash was heated in furnace at 1000 °C. The result of EDX analysis showed that silica samples have purity levels of 84.53% to 99.99%. FTIR result showed that silica samples have absorption bands at wave numbers of 1071 cm-1, 1060 cm-1 and 798 cm-1 which indicate the asymetric stretching vibration of Si-O from siloxane group. Keywords: silica, bamboo leaves, purity level, function group.
KARAKTERISASI JAMUR TIRAM PUTIH DENGAN MEDIA JAGUNG BULAT MENGGUNAKAN FOURIER TRANSFORM INFRARED Irlian Nurmaniah; Fitrah Hadi Firdaus; Ana Fitriana; Maya Risanti; Irmansyah Irmansyah; Irzaman Irzaman
PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) Vol 4 (2015): PROSIDING SEMINAR NASIONAL FISIKA (E-JOURNAL) SNF2015
Publisher : Program Studi Pendidikan Fisika dan Program Studi Fisika Universitas Negeri Jakarta, LPPM Universitas Negeri Jakarta, HFI Jakarta, HFI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (455.521 KB)

Abstract

The production of white oyster mushroom with a variation of load time baglog after an incubation period has been investigated. Based on the results obtained FTIR molecular C-O, C=O, C-H, and O-H on oyster mushrooms. Molecules C-O, C=O, and C-H indicates carbohydrates and O-H molecules indicate the presence of water. The results obtained from the characterization of Fourier Transform Infrared showed the opening day 35th after incubation mass has a moisture content which is small compared with the opening day 40th day and the 45th day. These results indicated a high transmittance value on the FTIR graph results. Keywords: FTIR, O-H cluster, white oyster mushroom, transmittance
Pembuatan Polikristal CuGaSe2 dan Penentuan Konstanta Kisinya Irmansyah Irmansyah; A. Harsono Supardjo; Arya Rezavidi
Indonesian Journal of Physics Vol 13 No 1 (2002): Vol. 13 No.1, Januari 2002
Publisher : Institut Teknologi Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (84.267 KB)

Abstract

Copper Galium Diselenide (CuGaSe2) Polycrystal was synthesized from a stoichiometric mixtures of the elements by using Bridgman Horizontal furnace single zoned. Ingot is visually solid and it did not attach on the ampoule walls. X-Ray Diffraction measurements show that the spectra are the Chalcopyrite peaks. The calculated lattice parameters obtained from Cohen Method are a=b= 5.613 Å , c = 11.014 Å and the ratio c/a =1.962
An Analysis of the Schrodinger Equation Model for the Distribution Rate of Stock Returns Agus Kartono; Hilda Meiranita Prastika Dewi; Irmansyah Irmansyah
Jurnal Ilmu Fisika Vol 15 No 2 (2023): September 2023
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jif.15.2.166-174.2023

Abstract

Quantum mechanics is a theory that describes the behavior of particles in the microscopic world. If the stock index can be considered an object on a macro scale, then every stock of a stock index is an object on a micro-scale. The stock price can be analogous to being a particle. This study aimed to obtain the density distribution of stock returns. Modeling stock returns distribution using a Schrodinger equation model with the assumption that stock is a particle in the good delta potential function so that stock returns as analogous to particles can be known. The Schrodinger equation can calculate stock returns expressed as an exponential distribution. The stock return density distribution using Schrodinger equation model has a higher kurtosis value than the kurtosis value in the normal distribution. The kurtosis value is the degree of the peak height of a distribution. The stock price data used is the stock price data of PT. United Tractors Tbk. and PT. Unilever Indonesia Tbk. during 2013-2018. This study shows the stock price of PT. Unilever Indonesia Tbk. has a more stable average stock price return with a more negligible risk of loss than the stock price of PT. United Tractors Tbk.
Effect of Different Hydrothermal Temperatures on the Properties on Nano-Silica (SiO2) of Rice Husk Irzaman Irzaman; Irmansyah Irmansyah; Siti Aisyah; Nazopatul Patonah Har; Aminullah Aminullah
International Journal of Renewable Energy Development Vol 11, No 3 (2022): August 2022
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.2022.43904

Abstract

Rice husk has high silica (SiO2) content and can be used as the primary material for making nano-silica. One of the methods for synthesizing nano-silica was the hydrothermal method. The objective of this study was to synthesize nano-silica from rice husks by observing the effect of temperature in the hydrothermal process on the structure, electrical and particle properties of nano-silica. The hydrothermal process temperature was 150, 200, and 250 °C for 4 hours. The results showed that all nano-silicas were in the amorphous phase. The particle size was in the range of 0.16-13.49 nm with more uniform size distribution on nano-silicas of 200 °C and 250 °C than nano-silica at 150 °C. These three nano-silicas were included in the semiconductor category by increasing temperature and frequency. In addition, these treatment variations resulted 200 °C for 4 hours and pressure of 2 atm as the optimum treatment for manufacturing nano-silica of rice husk ash. This nano-silica could be used as semiconductor material for electronic industry.
Predicting Oil Content of Palm Fruit Based on its Electrical Properties Verra Mellyana; I Wayan Budiastra; Irmansyah Irmansyah; Yohanes Aris Purwanto
Jurnal Teknik Pertanian Lampung (Journal of Agricultural Engineering) Vol. 14 No. 3 (2025): June 2025
Publisher : The University of Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtep-l.v14i3.933-946

Abstract

The oil content of oil palm fruit is a crucial parameter that must be determined before harvest, as it directly impacts crude palm oil (CPO) quality and processing efficiency. The conventional chemical method for oil content determination is costly and time consuming. This study aims to develop a non-destructive, accurate, and rapid method for predicting oil content in oil palm fruit based on its electrical properties. Measurements of electrical properties were taken across frequencies of 50 Hz to 5 MHz. Oil content of samples were determined by chemical method. Some pre-treatments of electrical properties were carried out and the pre-treated electrical properties were calibrated with reference oil content using simple linear regression and partial least squares regression. Linear regression model showed moderate accuracy (r = 0.61–0.81), with RMSE values between 9.54% and 12.99%. PLS regression models using admittance (r = 0.99, R² = 0.98, SEP 2.20%, RPD 7.99), resistance (r = 0.98, R² = 0.97, SEP 2.62%, RPD 5.56), and impedance (r = 0.98, R² = 0.95, SEP 3.16%, RPD 4.68) produced high prediction accuracy. The results confirm that electrical properties can be used to predict oil content in oil palm fruit rapidly and non destructively. Keywords: Electrical properties, Linear regression, Oil content, PLS.
The influence of plastic mulch degradation on microplastic contamination in agricultural soils under different climatic conditions Muhammad Firman Azima; Mersi Kurniati; Irmansyah Irmansyah; Rofiqul Umam
SAINS TANAH - Journal of Soil Science and Agroclimatology Vol. 22 No. 2 (2025): December
Publisher : Universitas Sebelas Maret

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/stjssa.v22i2.100546

Abstract

Plastic mulch is widely used in agriculture to improve crop productivity by regulating soil temperature, retaining moisture, and suppressing weed growth. However, its degradation produces microplastics that can accumulate in the soil, disrupt microbial communities, and potentially enter the food chain. This study examines microplastic contamination in agricultural soils under different climatic conditions: Bogor (humid) and Lombok (hot and dry). Various analytical techniques were employed to characterize material degradation, including FTIR spectroscopy, SEM, UV-Vis, and thermal conductivity measurements. The results show that differences in climate and environmental factors such as high temperature, UV exposure, and microbial activity can accelerate mulch degradation, resulting in higher microplastic concentrations in Lombok (455 ± 57.74 particles kg-1) compared to Bogor (265 ± 43.59 particles kg-1). FTIR analysis confirmed the presence of oxidation-derived functional groups (C=O, O-H), thermal analysis indicated a decrease in the material's thermal conductivity, UV-Vis revealed increased polymer chain scission, and SEM showed significant surface degradation. These findings highlight the environmental risks of plastic mulch use and underscore the importance of adopting more sustainable alternatives to reduce microplastic pollution in agricultural soils.
Identification key to nymphal and adult mealybugs (Hemiptera: Pseudococcidae) associated with dragon fruits in Indonesia Mila Seri Rezeki; IDHAM SAKTI HARAHAP; DEWI SARTIAMI; IRMANSYAH IRMANSYAH; GILLIAN W. WATSON
Biodiversitas Journal of Biological Diversity Vol. 22 No. 8 (2021)
Publisher : Society for Indonesian Biodiversity

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.13057/biodiv/d220804

Abstract

Abstract. Rezeki MS, Harahap IS, Sartiami D, Irmansyah, Watson GW. 2021. Identification key to nymphal and adult mealybugs (Hemiptera: Pseudococcidae) associated with dragon fruits in Indonesia. Biodiversitas 22: 3113-3118. Dragon fruit (Hylocereus spp.), belonging to Cactaceae family, is one of the horticultural commodities being developed in Indonesia for export. Phytosanitary regulations require that fruits for export must be free from diseases and pests, including mealybugs (Hemiptera: Pseudococcidae). Mealybug species commonly found on dragon fruits in Indonesia are Ferrisia virgata (Cockerell), Phenacoccus solenopsis Tinsley, Planococcus minor (Maskell) and Pseudococcus jackbeardsleyi Gimpel & Miller. Species-level identification of these insects in the nymphal phase is difficult due to the limited number of identification keys available, so it has been necessary to create an identification key to nymphs of mealybug species found on dragon fruit. A dichotomous identification key was constructed based on microscopic morphological characteristics of the cuticle. Thus, the four species can be differentiated based on general and unique characteristics of each species in the nymphal and adult stages. The diagnostic features that can be used to separate the four species in the nymphal phase are the presence or absence of: discoidal pores around the eyes; anal lobe bars; tubular ducts on the dorsum; and a denticle on each tarsal claw.
THE USE OF POLYMER GEL ELECTROLYTE CONTAINING I-/I3- REDOX COUPLE TO ASSEMBLY A SOLID STATE DYE SENSITIZED TiO2 SOLAR CELL Akhiruddin Maddu; Irmansyah Irmansyah; Mahfuddin Zuhri
Jurnal Sains Materi Indonesia Vol. 9 No. 1 (2007): Jurnal Sains dan Materi Indonesia
Publisher : BRIN Publishing (Penerbit BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/jusami.2007.9.1.4826

Abstract

THE USE OF POLYMER GEL ELECTROLYTE CONTAINING I-/I3- REDOX COUPLE TO ASSEMBLY A SOLID STATE DYE SENSITIZED TiO2 SOLAR CELL. A solid state dye sensitized TiO2 nanocrystalline solar cells was assembled employing a polymer gel electrolyte contains of iodide/triiodide (I-/I3-) redox couple. The use of solid electrolyte based on polymer matrix for redox ‘couples is aimed to overcome several problems of liquid cell, such as leaks of electrolyte that result in degradation of solar cell. TiO2 nanocrystalline layer was grown on TCO glass substrate by doctor blade technique was stained by synthetic dye Ruthenium 535 for a day. To complete the cell, a polymer gel based on poly(ethylene glycol) (PEG) containing I-/I3- redox couple was sandwiched between a working electrode (nanoporous TiO2 layer on conductive glass substrate) and a counter electrode (graphite sheet). The solid-state cell does not need a clipp, so the gel polymer electrolyte also acts as a glue to join the electrodes. Two cells assembled with different amount of I-/I3- redox couple used in each cell, one of cell use 20 drops of Iodolyte (contains (I-/I3- redox couple) and another cell use 30 drops of Iodolyte solution (purchased fromSolaronix, SA). The cells were characterized their photovoltaic performances included: open-circuit voltage (Voc), short-circuit current (Isc),maximum power (Pmax), fill factor (FF) and energy conversion efficiency.