Yatno Dwi Agus Susanto
Unknown Affiliation

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

PENDAYAGUNAAN UNIT PELARUTAN YELLOW CAKE PILOT CONVERSION PLANT (PCP) SEBAGAI EVAPORATOR CAIRAN LIMBAH URANIUM Ade Saputra Ade Saputra; Yatno Dwi Agus Susanto; Hanif Ghufron Hanif Ghufron; Anita Sari Sari
PIN Pengelolaan Instalasi Nuklir Vol 12, No 23 (2019): Oktober 2019
Publisher : PIN Pengelolaan Instalasi Nuklir

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

ABSTRAK - Limbah cair atau efluen hasil samping proses pemurnian di PCP masih memiliki kadar uranium sebesar ± 20 gU/liter. Kadar tersebut terlalu tinggi untuk dijadikan limbah dan dikirim ke Pusat Teknologi Limbah Radioaktif (PTLR), namun tidak ekonomis jika langsung diproses di PCP sebagai umpan proses pemurnian. Oleh karena itu perlu dilakukan proses evaporasi sehingga uraniumnya dapat dipunggut kembali sebagai ekstrak dan kondensatnya dapat di kirim ke PTLR sebagai limbah. Pembuatan unit evaporator baru untuk mengolah limbah akan membutuhkan biaya tinggi sehingga pendayagunaan unit pelarutan yellow cake sebagai evaporator perlu dilakukan. Proses pendayagunaan unit pelarutan yellow cake meliputi proses utilisasi sistem pemipaan tangki pelarutan dan percobaan evaporasi limbah efluen secara batch menggunakan unit pelarutan yellow cake untuk mengetahui unjuk kinerja proses evaporasi. Unit pelarutan yellow cake dapat didayagunakan sebagai sistem evaporator dengan memodifikasi sistem pemipaan untuk mengurangi volume limbah cair uranium di PCP dengan kapasitas ± 80 liter/jam dengan kadar uranium di kondensat sebesar ±10 ppm dan mendekati baku tingkat radioaktivitas yang ditetapkan BAPETEN. Kata Kunci - Evaporasi, Pendayagunaan, Pelarutan, Limbah, Uranium   ABSTRACT - Liquid waste or effluent by product of the purification process at PCP, still has uranium content about ± 20 gU/liter. The level was too high as waste and sent to The Radioactive Waste Technology Center (PTLR), but it is not economical if it is processed at PCP as a feed for the purification process. Therefore it is necessary to do the evaporation process so that the uranium can be extracted as an extractant and the condensate can be sent to the PTLR as waste. The build up of a new evaporator unit to process waste will be high cost, so that utilization of yellow cake dissolution unit as an evaporator is carried out. The utilization of the yellow cake dissolution unit includes the utilization of the piping system and evaporation experiment to determine the performance of the evaporation process. Yellow cake dissolution unit can be utilized as an evaporator system by modifying the piping system to reduce the volume of uranium liquid waste in PCP. The capacity is about ± 80 liters / hour for uranium concentration in the condensate about ± 10 ppm and approaching the radioactivity level has determined by BAPETEN. Keywords - Evaporation, Utilization, Dissolution, Waste, Uranium
PERCOBAAN PEMBUATAN PELAT ELEMEN BAKAR U-7Mo-xSi/Al DALAM UKURAN MINI Supardjo; Agoeng Kadarjono; Isfandi; Yatno Dwi Agus Susanto; Setia Permana; Guswardani
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 25 No. 3 (2019): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2019.25.3.5697

Abstract

The purpose of this study is to obtain the optimized process parameters in the fabrication of a U-7Mo-xSi/Al mini plate complying with the specifications. The process flow started with synthesizing U-7Mo-xSi alloys (x = 1%, 2%, and 3%) using depleted uranium and continued to preparing U-7Mo-xSi powder, U-7Mo-xSi/Al fuel core, and U-7Mo-xSi/Al fuel element plates. The quality of the product was determined by analyses/tests including tests of raw materials and products from each end of the process by the appropriate type of test which is commonly applied to the manufacturing process of plate type fuel. The quality of U-7Mo-xSi alloy ingots, U-7Mo-xSi powder, and U-7Mo-xSi/Al fuel core was satisfactorily good and in compliance with the specifications, indicating that the applied process parameters were appropriate. The obtained fuel element plates, however, have not satisfied the requirements especially the thickness of the cladding, where there are still several measurement points whose thickness is <0.25 mm. To obtain cladding thickness according to the required specifications, it is necessary to experiment with other rolling parameters or replacing the cladding material with material of higher hardness.
PRODUCTION OF URANIUM-MOLYBDENUM ALLOY AS A CANDIDATE FOR NUCLEAR RESEARCH REACTOR FUEL Ganisa Kurniati Suryaman; Muhammad Waziz Wildan; Supardjo; Yatno Dwi Agus Susanto
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 24 No. 3 (2018): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2018.24.3.4685

Abstract

Research and development on high density uranium for nuclear research reactor fuel is still in progress. Uranium-molybdenum alloy is one of the strongest candidates of nuclear research reactor fuel material. The properties and characteristics of U-Mo alloy is of important consideration for the selction of the fabrication techniques for the production of the fuel. In this work, uranium-molybdenum (U-Mo) alloys with varied molybdenum content have been produced succesfully by arc melting technique. The molybdenum content variations were 7 %wt, 8 %wt, 9 %wt and 10 %wt Mo. The melting process was done 5 times to achieve homogenization. Metallographic micrograph shows the presence of dendritic structure. XRD examination result affirms the presence of 2 phases of γ-U phase and d-U2Mo phase. Microhardness Vickers test shows higher hardness value for Uranium-molybdenum alloy with higher molybdenum content.
KARAKTERISTIK MEKANIK KELONGSONG BAHAN BAKAR NUKLIR TEMPERATUR TINGGI DALAM ATMOSFER GAS NITROGEN Rohmad Sigit; Sri Ismarwanti; Guswardani; Yatno Dwi Agus Susanto; Jan Setiawan
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 24 No. 2 (2018): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2018.24.2.4422

Abstract

At Loss of Cooling Accident (LOCA) scenario, Zr-2 and Zr-4 as nuclear fuel cladding potentially exposed to air which experimentally leads to mechanical properties degradation faster than in steam environment. This study aims to determine the impact of nitrogen on the mechanical strength of cladding by minimizing other environmental influences. The Zr-2 and Zr-4 cladding was annealed under vacuum at a temperature of 500°C for one hour. It was followed by nitriding with the pressure of 1500 mbar for two hours. It was followed by natural cooling to room temperature. The results of tensile strength and microhardness testing showed that tensile strength, ductility and microhardness values increase of 12.1%, 19.2% and 28.2% for Zr-2 and 5.1%, 25% and 22.6% for Zr-4, respectively. Nitride layer was formed on the cladding surface due to interaction with nitrogen and there is no mechanical properties degradation due to nitriding process. It was caused by nitriding processes that were not followed or accompanied by oxidation processes.