Muhammad Sholeh
BBKKP

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

Pengaruh rasio MBTS/ZDEC pada campuran karet alam dan etilen propilen diena yang dibuat dengan teknik kontrol migrasi curatives Ihda Novia Indrajati; Muhammad Sholeh
Majalah Kulit, Karet, dan Plastik Vol 30, No 1 (2014): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20543/mkkp.v30i1.124

Abstract

The objective of this research was to observe the effect of MBTS/ZDEC ratio on dynamic properties, curing characteristic, morphology as well as hardness and resiliency of the NR/EPDM blends prepared by curatives migration control technique. The MBTS/ZDEC ratio were 1.6/0.0; 1.5/0.1; 1.4/0.2; 1.3/0.3 and 1.2/0.4 respectively on a fixed NR/EPDM ratio of 60/40. Compounds (EPDM and NR) were prepared separately using two roll mill. The blends with binary accelerator MBTS/ZDEC showed synergistic activity which provided higher crosslink density than those of single accelerator MBTS. Reduction of ts2 and t90 as well as cure rate index (CRI) indicated the more homogeneous crosslink density distribution within the rubber phase. Scanning electron micrograph showed that the blends with binary accelerator gave smoother surface. Binary accelerator resulted higher hardness. Increasing of ZDEC raised hardness followed by reduction of the resillience property.ABSTRAKPenelitian ini bertujuan mempelajari pengaruh rasio MBTS/ZDEC pada sifat dinamik, karakteristik curing, karakteristik morfologi serta kekerasan dan sifat pegas pantul campuran NR/EPDM yang dibuat dengan teknik kontrol migrasi curatives. Rasio MBTS/ZDEC yang digunakan dalam penelitian ini secara berurutan 1,6/0,0; 1,5/0,1; 1,4/0,2; 1,3/0,3; dan 1,2/0,4 pada rasio NR/EPDM tetap 60/40. Kompon dibuat secara terpisah (kompon EPDM dan NR) menggunakan two roll mill. Campuran NR/EPDM dengan akselerator biner MBTS/ZDEC menunjukkan sinergi aktivitas yang memberikan kerapatan ikatan silang lebih tinggi daripada akselerator tunggal MBTS. Kemampuan proses kompon akselerator biner lebih rendah daripada akselerator tunggal. Penurunan ts2 dan t90 serta kenaikan indeks kecepatan reaksi (CRI) mengindikasikan distribusi ikatan silang yang merata pada kedua fasa karet. Mikrograf pemindaian elektron (SEM) menunjukkan campuran dengan akselerator biner mempunyai permukaan yang lebih halus. Kekerasan vulkanisat sistem biner lebih tinggi. Penambahan ZDEC meningkatkan kekerasan dan diikuti dengan penurunan sifat pegas pantul.
Peningkatan kualitas air limbah terolah industri penyamakah kulit menggunakan taman tanaman air dengan tumbuhan bambu air Prayitno Prayitno; Muhammad Sholeh
Majalah Kulit, Karet, dan Plastik Vol 30, No 1 (2014): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (894.781 KB) | DOI: 10.20543/mkkp.v30i1.120

Abstract

A research of constructed wetland system vegetated with Equisetum hyemale for treating of treated tannery wastewater have been conducted. The constructed wetland was 3 m long, 1 m wide, and 1 m deep or equal with volume of 3 m3. The construction of wetland consisted of 4 main layers (from the bottom to the top): 0.3 m of rock; 0.3 m of gravel; 0.1 m of black sugar-palm fiber; and 0.3 m of sand. The wetland was operated with subsurface flow system (SSF). The detention time was varied at 3.125; 2.083; and 1.563 days. The result showed that the optimum removal were 60.60% for COD with detention time of 3.125 days, 60.17% for BOD with detention time of 2.083 days, 93.76% for TSS with detention time of 3.125 days, 89.02%  for S with detention time of 3.125 days and 96.89% for total chrome wth detention time of 2.083 days.ABSTRAKTelah dilakukan penelitian taman tanaman air (TTA) dengan tanaman bambu air untuk mengolah limbah cair terolah industri penyamakan kulit. Konstruksi TTA berukuran panjang 3 m, lebar 1 m, dan dalam 1 m, atau sama dengan volume 3 m3. Media terdiri atas empat lapisan mulai dari bawah adalah koral 0,3 m, kerikil 0,3 m, ijuk 0,1 m, dan lapisan paling atas adalah pasir 0,3 m. TTA dioperasikan dengan sistem aliran subsurface (SSF). Waktu tinggal divariasi berturut-turut pada 3,125; 2,083; dan 1,563 hari. Hasil penelitian menunjukan efektivitas penurunan COD sebesar 60,60% dengan waktu tinggal 3,125 hari, penurunan BOD sebesar 60,17% dengan waktu tinggal 2,083 hari, penurunan TSS sebesar 93,76% dengan waktu tinggal 3,125 hari, penurunan S sebesar 89,02% dengan waktu tinggal 3,125 hari dan penurunan krom sebesar 96,89% dengan waktu tinggal 2,083 hari.