Article Per Year (5 Year)
p-Index From 2021 - 2026
0.659
P-Index
This Author published in this journals
All Journal International Journal of Electrical and Computer Engineering Bulletin of Electrical Engineering and Informatics Jurnal Teknik Elektro
Dwi Mandaris
National Research and Innovation Agency
Computer Science & IT Electrical & Electronics Engineering

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Electromagnetic interference measurement for axle counters light rapid transit railway in Indonesia Yudhistira Yudhistira; Yoppy Yoppy; Elvina Trivida; Tyas Ari Wahyu Wijanarko; Hutomo Wahyu Nugroho; Dwi Mandaris
International Journal of Electrical and Computer Engineering (IJECE) Vol 12, No 5: October 2022
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijece.v12i5.pp4632-4639

Abstract

The measurement and analysis of electromagnetic interference (EMI) from light rapid transit (LRT) axle counters against magnetic field interference in Indonesia has been carried out. The low-cost magnetic sensors were developed according to the British Standard (BS) EN 50592:2016. The measurement setup and magnetic field limit were based on the British Standard EN 50592:2016 and ERA/ERTMS/033281 standard. Two frequency range of the measurements, lower and higher frequencies with two different train running mode, acceleration mode and deceleration mode were applied in this research. The results in lower frequency range (10 to 100 kHz) were very close to the limit value in both acceleration and deceleration mode, especially at the 30 to 50 kHz for the y and z directions. Although there may possibly magnetic interference at low frequencies, most of the magnetic field emissions were still in acceptable range.
Design and Optimization of Discone Antenna for Medical Device Electromagnetic Interference Measurement Haryo Dwi Prananto; Dwi Mandaris; Aditia Nur Bakti; Achmad Munir
Jurnal Teknik Elektro Vol 15, No 1 (2023): Jurnal Teknik Elektro
Publisher : Jurusan Teknik Elektro, Fakultas Teknik, Universitas Negeri Semarang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.15294/jte.v15i1.39688

Abstract

The wide spread of the Internet of Things creates the possibility of electromagnetic interference in medical devices. Therefore, it is necessary to perform risk mitigation by finding the value of electromagnetic interference through measurements using wideband and omnidirectional antennas, e.g., the discone antenna. In this research, the optimization of the S11 value of a designed discone antenna was obtained using simulation from the effect of dimensional variations in discone parameters like disc diameter, cone bottom diameter, gap, and cone height on S11 characteristics. The parameters were combined for optimization. The design was fabricated, and the S11, radiation pattern, gain value and antenna factor, and the ability to measure interference through modeling were measured. Gain value and antenna factor were obtained using the gain-comparison method, which compared the antenna of interest against another antenna with a standard gain. The optimization was successfully performed with a better S11 value. At 5.2 GHz, the value of S11 was below -10 dB. The realization of the design showed similar results to the simulation, and it was found to be able to operate in the medical device frequency range (wideband). The ability of the discone antenna improved in terms of S11 value, especially at 5.2 GHz, where the value was below -17.443 dB. The radiation pattern of the designed antenna is omnidirectional. Additionally, validation was carried out by providing gain value and antenna factor. It has been proved that the designed discone antenna could measure interference successfully by modeling interference sources as electric field sources from all directions.
Design and development of automatic voltage regulator using Ziegler-Nichols PID for electrical irons testing Irawan Sukma; Aji Dwi Suseno; Muhidin Muhidin; Prayoga Bakti; Wuwus Ardiatna; Ihsan Supono; Himma Firdaus; Dwi Mandaris
Bulletin of Electrical Engineering and Informatics Vol 13, No 6: December 2024
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v13i6.7326

Abstract

This research presents an automated voltage regulation system crucial for a power input test of electric irons based on SNI IEC 60335-2-3 clause 11.4. The system is designed with an Arduino-based proportional-integral-derivative (PID) control mechanism to augment voltage stability and meet the standard requirement. The system comprises a microcontroller for PID control, a dimmer as the actuator, and a voltage sensor for error measurement. It utilizes the Ziegler-Nichols (Z-N) oscillation method to determine the PID control parameters. The simulation results identified a third-order transfer function as the best fit for the system, and the optimal PID parameters for the system are Kp=60, Ki=125, and Kd=500. The system was tested under the electric iron's active and non-active conditions. The proposed PID system demonstrated stable responses, effectively regulating the system voltage with minimal overshoot and settling time, and meeting standard requirements even under varying load conditions. It suggests potential applications beyond electric iron testing, promising efficiency improvements in broader household product testing.
Co-Authors Achmad Munir Aditia Nur Bakti Aji Dwi Suseno Elvina Trivida Haryo Dwi Prananto Himma Firdaus Hutomo Wahyu Nugroho Ihsan Supono Irawan Sukma Muhidin Muhidin Prayoga Bakti Tyas Ari Wahyu Wijanarko Wuwus Ardiatna Yoppy Yoppy Yudhistira Yudhistira