Rosita Dwi Chrisnandari
Department of Chemical Engineering, Politeknik Negeri Malang, Jl. Soekarno Hatta No. 9, Malang 65141, Indonesia

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

Utilization of Yellow Shells (Cypraea moneta) in the Treatment of Cadmium Heavy Metal (Cd) Waste Noor Isnaini Azkiya; Rosita Dwi Chrisnandari; Wianthi Septia Witasari
Jurnal Teknik Kimia dan Lingkungan Vol. 7 No. 1 (2023): April 2023
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (350.217 KB) | DOI: 10.33795/jtkl.v7i1.327

Abstract

Cadmium (Cd) metal is a heavy metal that can cause environmental pollution if its levels are above the environmental quality standard value. Generally, industrial wastes such as paper industry waste contain heavy metal Cd with levels reaching 0.026 ppm. Meanwhile, the quality standard for Cd metal in the environment is 0.005 ppm. For this reason, it is necessary to process it to reduce the levels of Cd metal in the waste before being discharged into the environment. One way that can be used to reduce the levels of Cd metal is by adsorption method using Cypraea moneta clamshells containing chitin. This study used variations in the particle size of the shellfish adsorbent of 6 and 12 mesh. In addition, the ratio of the amount of adsorbate and adsorbent (mg:mg) is 1 : 0.5x106; 1 : 1x106; and 1 : 1.5x106. Based on the results obtained, it showed that the use of shellfish as an adsorbent was able to reduce Cd metal content up to 89%.
Enhanced Removal of Copper from Synthetic Wastewater Using a Water Hyacinth-Based Activated Carbon and Chitosan Composite Adsorbent Rosita Dwi Chrisnandari; May Kurnia Pratiwi; Ria Lusiyani
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 2 (2026): October 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i2.9227

Abstract

Copper (Cu) contamination of rivers or groundwater is a worldwide problem caused by anthropogenic activities, commonly from the industrial sector. Cu accumulation in the body could have detrimental effects on human health as well as pose a major threat to the aquatic environment. We report the rate of Cu removal by a composite made from activated carbon of water hyacinth and chitosan in an artificial aqueous Cu solution which is likely to be encountered in terrestrial environments. In this investigation, water hyacinth has been processed by carbonization in a batch reactor at 350°C for 90 minutes. The chars were also chemically modified with HCl 6 N for 24 hours to investigate the potential for sorption enhancement. The properties of the resulting chars including their water content, ash content, volatile matter, fixed carbon, and iodine absorption capacity properties have been determined and compared to Indonesia’s standard (SNI 06-3730-1995). Composites have been produced by mixing the activated carbon with chitosan (1% w/v; 2% w/v; 3% w/v) from crab shells in an STTP-Ethanol solution. The composite was characterised using Fourier transform infrared spectroscopy (FT-IR). The effects of contact time parameters on batch system adsorption were investigated. Adsorption isotherm models including Langmuir and Freundlich were applied to interpret the equilibrium data in aqueous solutions. For a kinetic model consistent with experimental data, pseudo-first-order and pseudo-second-order models were examined. The maximum adsorption capacity was calculated as 0,006510 mg/g. Meanwhile, the most suitable isotherm and kinetic models were Langmuir and pseudo-second-order kinetic models, respectively. Adsorption has optimum results at room temperature, with an initial metal concentration of 0.135 mg/L, contact time of 60 min, and 1 g dosage for the adsorbent. The highest removal rate for Cu was observed for the composite with typical rates ranging from 95.74 – 96.41%. The removal rate for activated carbon from water hyacinth is lower and ranges from 94.12 – 95.07%. Meanwhile, the removal rate using chitosan alone is 95.33%. This study confirms that the addition of chitosan improves the efficiency of activated carbon to remove Cu compared to the original state.
Optimization of Tobacco-Stem Bio-Oil Production by Catalytic Pyrolysis Using Activated Natural Zeolite and Response Surface Methodology Cucuk Evi Lusiani; Farah Shifa Fayyaza; Tiara Salsabilla; Ade Sonya Suryandari; Rosita Dwi Chrisnandari; Heny Dewajani; Mochammad Agung Indra Iswara
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 2 (2026): October 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i2.11240

Abstract

Tobacco stem is a lignocellulosic agricultural residue with potential for bio-oil production through catalytic pyrolysis. This study investigated the effects of pyrolysis temperature, reaction time, and acid-activated natural zeolite loading using Response Surface Methodology (RSM) with a Box–Behnken Design. Bio-oil yield, density, viscosity, and pH were evaluated, supported by FTIR and GC-MS characterization. The distilled bio-oil yield ranged from 15.47 to 68.79 wt%, with the highest yield obtained at 550°C, 3 h, and 10 wt% zeolite. The RSM model for bio-oil yield was statistically significant (p=0.0474), with zeolite loading being the most influential factor (p=0.0121). In contrast, the models for density, viscosity, and pH were not statistically significant. Numerical optimization identified a model-predicted candidate condition of 527.70°C, 2.55 h, and 12.36 wt% zeolite, with a predicted distilled bio-oil yield of 69.08 wt%. Experimental validation is required to assess the predictive accuracy of this condition. The results indicate that activated natural-zeolite loading was the most influential statistically significant factor affecting bio-oil yield within the investigated domain.