Cucuk Evi Lusiani
Department of Chemical Engineering, Politeknik Negeri Malang, Jl. Soekarno Hatta No. 9, Malang 65141, Indonesia

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

Producing Precipitated Calcium Carbonate (PCC) from CO2 Emissions during OFMSW Bio-Drying through Carbonation: A Preliminary Study Eko Naryono; Cucuk Evi Lusiani; Mochammad Agung Indra Iswara; Abdul Chalim; Noor Isnaini Azkiya; Amalia Dwi Ardini Putri; Allivia Retnaning Tyas; Kaliawan Kaliawan
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 1 (2026): April 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i1.9573

Abstract

Capturing CO₂ emissions during the bio-drying process of organic fraction municipal solid waste (OFMSW) presents an alternative approach to reducing CO₂ emissions in municipal solid waste (MSW) management. Absorption using an aqueous solution of Ca(OH)₂ is a viable CO₂ capture technology that produces precipitated calcium carbonate (PCC), a value-added product. The objectives of this study are to assess the impact of bio-drying aeration flow rate and absorption time in the Ca(OH)₂ solution on CO₂ absorption efficiency, the conversion of Ca(OH)₂, and the mass of the PCC product. The absorption process was performed in a semi-continuous bubble reactor with 15 L of 0.019 M Ca(OH)₂ aqueous solution. At bio-drying aeration flow rates of 5.1, 4.6, and 3.9 L/min/kg of waste, with CO₂ concentrations ranging from 1286 to 4395 ppm and temperatures between 23 to 30°C over a bio-drying period of 96 hours, it was observed that higher flow rates resulted in lower conversion rates of Ca(OH)₂ and reduced CO₂ absorption efficiency. The highest recorded conversion rates for Ca(OH)₂ and CO₂ absorption were 97.3% and 16.4%, respectively, yielding a PCC product of 4.8 g/kg of waste at an aeration flow rate of 3.9 L/min/kg waste and an absorption duration of 48 hours. FTIR and SEM analysis confirmed the presence of both calcite and aragonite crystal forms in the PCC product, as well as hydrated CaCO₃.
Optimization of Tobacco-Stem Bio-Oil Production by Catalytic Pyrolysis Using Activated Natural Zeolite and Response Surface Methodology Cucuk Evi Lusiani; Farah Shifa Fayyaza; Tiara Salsabilla; Ade Sonya Suryandari; Rosita Dwi Chrisnandari; Heny Dewajani; Mochammad Agung Indra Iswara
Jurnal Teknik Kimia dan Lingkungan Vol. 10 No. 2 (2026): October 2026
Publisher : Politeknik Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33795/jtkl.v10i2.11240

Abstract

Tobacco stem is a lignocellulosic agricultural residue with potential for bio-oil production through catalytic pyrolysis. This study investigated the effects of pyrolysis temperature, reaction time, and acid-activated natural zeolite loading using Response Surface Methodology (RSM) with a Box–Behnken Design. Bio-oil yield, density, viscosity, and pH were evaluated, supported by FTIR and GC-MS characterization. The distilled bio-oil yield ranged from 15.47 to 68.79 wt%, with the highest yield obtained at 550°C, 3 h, and 10 wt% zeolite. The RSM model for bio-oil yield was statistically significant (p=0.0474), with zeolite loading being the most influential factor (p=0.0121). In contrast, the models for density, viscosity, and pH were not statistically significant. Numerical optimization identified a model-predicted candidate condition of 527.70°C, 2.55 h, and 12.36 wt% zeolite, with a predicted distilled bio-oil yield of 69.08 wt%. Experimental validation is required to assess the predictive accuracy of this condition. The results indicate that activated natural-zeolite loading was the most influential statistically significant factor affecting bio-oil yield within the investigated domain.