Article Per Year (5 Year)
p-Index From 2021 - 2026
0.444
P-Index
This Author published in this journals
All Journal Jurnal Teknik Industri Terintegrasi (JUTIN) Petrogas : Journal of Energy and Technology
Yudiaryono Yudiaryono
STT Migas Balikpapan
Chemical Engineering, Chemistry & Bioengineering Decision Sciences, Operations Research & Management Earth & Planetary Sciences Electrical & Electronics Engineering Energy Engineering Industrial & Manufacturing Engineering Mechanical Engineering

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
MEMPREDIKSI KEADAAN SUMUR DIMASA DEPAN DENGAN MELAKUKAN OPTIMASI MENGGUNAKAN ELECTRICAL SUBMERSIBLE PUMP PADA SUMUR “AD-96” Muhammad Adnan; Rohima Sera Afifah; Yudiaryono Yudiaryono
PETROGAS: Journal of Energy and Technology Vol 3, No 1 (2021): March
Publisher : Sekolah Tinggi Teknologi MIGAS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.58267/petrogas.v3i1.47

Abstract

The production capacity of an oil and gas well is a benchmark in planning production equipment and increases the flow rate of production. In order to increase the rate of oil production, optimization is done optimally using ESP and it is predicted that the production time will be several years ahead. The method used in the well "AD-96" is the Wiggins Method 3 Phase IPR curve to increase the optimal production flow rate by continuing to predict IPR Future through a gradual decrease in reservoir pressure (Pr) scenario. IPR Future in this case provides a development to know the wells in the future. The results of the calculation of Wiggins IPR curve on the well "AD-96" obtained a maximum production rate (Qmax) of 2469 bfpd. To estimate the optimal production rate obtained from a percentage of 80% x maximum flow rate of 1975 bpd, the well is advised to use the Electrical Submersible Pump design with the ESP REDA type pump type DN1800 Pump Performance Curve 60 Hz, 3500 rpm and a Horse Power of 29 HP. , efficiency 76% and IPR Future with water cut of 80% each carried out in the calculation of 4 scenarios at 2000 psia reservoir pressure, obtained a target production flow rate (Qtarget) of 1326 bpd. It is known that the recommended production (recommended production) is between 1200-2400 bpd. Based on the IPR Future scenario, the result shows that ESP does not work at a pressure of 2000 psia.
Analisa Pengaruh Kehilangan Tekanan terhadap Pengikisan Material Sand Trap Sumur X Lapangan Y Mira Isabela; Risna Risna; Abdul Gafar Karim; Nijusiho Manik; Yudiaryono Yudiaryono
Jurnal Teknik Industri Terintegrasi (JUTIN) Vol. 9 No. 3 (2026): July
Publisher : LPPM Universitas Pahlawan Tuanku Tambusai

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31004/jutin.v9i3.61389

Abstract

Milling operations on the sand trap of Well X, Field Y—a mature field—face reduced cleaning efficiency due to uncertain pressure loss distribution within the Coiled Tubing Unit (CTU) circulation system. This study analyzes the magnitude of pressure losses, maps the specific locations of hydraulic energy depletion, and determines the optimal pump flow rate to establish a safe hydraulic window that prevents lost circulation. The method applied is a mathematical hydraulic analysis covering hydrostatic pressure, bit pressure loss (Pb), annular velocity (AV), and Equivalent Circulating Density (ECD), with sensitivity analysis across three pump flow rates (1.1, 1.2, and 1.3 bbl/min). Results show pressure losses accumulate at three critical points: inside the coiled tubing due to helical buckling, at the junk mill nozzle, and across the Positive Displacement Motor (PDM), which suffers wear from abrasive sand. A flow rate of 1.2 bbl/min (50.4 gpm) proved optimal, yielding an annular velocity of 184.24 ft/min—exceeding the minimum critical limit (>180 ft/min)—while maintaining ECD at 8.534 ppg, safely below the formation fracture gradient.
Co-Authors Mira Isabela Muhammad Adnan Nijusiho Manik Risna Risna Rohima Sera Afifah