cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota bandung,
Jawa barat
INDONESIA
Mesin
Published by Institut Teknologi Bandung
ISSN : -     EISSN : -     DOI : -
Core Subject : Engineering,
Mechanical Engineering
Arjuna Subject : -
Articles 5 Documents
 1 
Search results for , issue "Vol. 20 No. 1 (2005)" : 5 Documents clear
PERANCANGAN DAN PEMBUATAN ALAT UJI KOMPRESOR REFRIGERASI Willy Adriansyah
Mesin Vol. 20 No. 1 (2005)
Publisher : Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

A compressor testing device based on vapor compression cycle has been designed and built successfully. Simple and easy operation is the main differences between the device and conventional compressor testing device. A reciprocating compressor performance was tested for two kind of refrigerants; R22 and HCR22 using this device. From the experimental results it is found that the isentropic efficiency can be represented by a two degrees polynomial function. The experimental results also shows that the isentropic efficiency of the compressor using R22 is higher compared to the same compressor using HCR22.
ANALISIS SISTEM TATA UDARA DI DALAM KABIN KENDARAAN MINIBUS DENGAN MENGGUNAKAN PERANGKAT LUNAK COMPUTATIONAL FLUID DYNAMICS T. A Fauzi Soelaiman; Andini Aritonang
Mesin Vol. 20 No. 1 (2005)
Publisher : Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The aim of this research is to establish an analysis of an air conditioning system in a minibus vehicle cabin through some series of numerical simulations using a Computational Fluid Dynamics software. Two three-dimensional models of the vehicle were used in the simulations. The first model is a minibus without any passenger, and the second model is a minibus with seven passengers. In this research, the passenger model was considered as another cooling load source, therefore an analysis of the cooling effect experienced by passenger was not performed. A calculation of cooling load was also done to determine the maximum cooling load, using the weather data of Jakarta city throughout the year 2002. An experiment was done using an actual vehicle to validate the model. The maximum error of temperature reading between experiment and simulation was calculated and gave an acceptable maximum error of 10%. The simulation in this step was performed using the first model and steady calculation. A series of simulations were also done to analyze the air conditioning system performance under maximum cooling load. These simulations were done by varying the mass flow rates of the air entering the cabin, using the second model and transient calculations. The temperature and velocity contours acquired from these simulations were able to give good understanding of correlations between the factors influencing the air condition in the cabin.
ANALISIS PERCABANGAN RETAK PADA MATERIAL KERAMIK PIEZOELEKTRIK IGN Wiratmaja Puja; Muhamad Hidayat; Qing Hua Qin
Mesin Vol. 20 No. 1 (2005)
Publisher : Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Crack branch or kink in piezoelectric body may occur due to mechanical or electric loading. This paper presents the analysis of crack branch for ceramic piezoelectric materials. This type of advanced materials is very advantageous for application in smart structures, measurements device and actuators. Utilizing the extended Stroh Formalism for elastoelectric, the boundary value problems are solved by way of Hilbert Transforms. The explicit expressions for the elastic, electric, stress and electric intesity factor, and strain energi density are presented in integral forms. These integrals are solved using Gauss-Chebysev-Quadrature. Numerical results for piezoelectric ceramics are presented to illustrate both qualitative and quantitative behaviour of the stress- electric intesity factors.
KAJI NUMERIK DAN EKSPERIMENTAL PERPINDAHAN PANAS PADA EVAPORATOR UNTUK MENDINGINKAN UDARA Prihadi Setyo Darmanto; Deddy Dwi Arjanto; Muhammad Ismail
Mesin Vol. 20 No. 1 (2005)
Publisher : Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This paper presents numerical and experimental study of heat transfer on fins-tube heat exchanger that functioned as an evaporator for coolingof humid air. In this case, change of phase occurred both on air and refrigerant. The proposed numerical analysis is based on the application of mass and energy balances implemented at small control volumes that were part of evaporator. The result of numerical evaluation was then compared to the experimental observation. A good agreement between experimental and numerical results was achieved and the proposed numerical method also could be used as a tool in designing fins tube heat exchanger with phase change in both fluids.
PENGGUNAAN TEKNIK APROKSIMASI (METAMODELING) UNTUK MENYEDERHANAKAN MODEL ELEMEN HINGGA DALAM PROSES OPTIMASI Rachman Setiawan
Mesin Vol. 20 No. 1 (2005)
Publisher : Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Complex modelling using Finite element method in iterative optimisation process often yield expensive computation. One of the solution is to replace the expensive finite element analysis with a mathematically simpler model, that is using an approximate relations (Metamodel). Here, the approach is used to characterise the mechanical properties of an anisotropic plate from their corresponding natural frequencies. Radial basis functions model has been chosen for the Metamodel to approximate the finite element model generated in ANSYS 6.1 software. Characterisation process is regarded as an optimisation problem with the objective is to minimise the accumulation of differences between the target frequencies and the updated ones. The use of Metamodel shorten the computation time as well as increase the likelihood of reaching the global minimum. In general, the overall result is reasonably good to predict the mechanical properties of anisotropic plates.

Page 1 of 1 | Total Record : 5

 1 

Filter by Year

2005 2005


Reset
Filter By Issues
All Issue Vol 30 No 2 (2025) Vol 30 No 1 (2024) Vol 29 No 2 (2023) Vol 29 No 1 (2023) Vol. 28 No. 1 (2019) Vol 27, No 2 (2018) Vol. 27 No. 2 (2018) Vol 27, No 1 (2018) Vol. 27 No. 1 (2018) Vol. 26 No. 2 (2017) Vol 26, No 2 (2017) Vol 26, No 2 (2017) Vol 26, No 1 (2017) Vol. 26 No. 1 (2017) Vol 25, No 2 (2016) Vol. 25 No. 2 (2016) Vol 25, No 1 (2016) Vol. 25 No. 1 (2016) Vol 24, No 2 (2009) Vol. 24 No. 2 (2009) Vol 24, No 1 (2009) Vol. 24 No. 1 (2009) Vol 23, No 2 (2008) Vol. 23 No. 2 (2008) Vol. 23 No. 1 (2008) Vol 23, No 1 (2008) Vol 23, No 1 (2008) Vol 22, No 2 (2007) Vol. 22 No. 2 (2007) Vol. 22 No. 1 (2007) Vol 22, No 1 (2007) Vol. 21 No. 2 (2006) Vol 21, No 2 (2006) Vol 21, No 1 (2006) Vol. 21 No. 1 (2006) Vol 21, No 1 (2006) Vol 20, No 2 (2005) Vol. 20 No. 2 (2005) Vol 20, No 1 (2005) Vol. 20 No. 1 (2005) Vol 19, No 2 (2004) Vol. 19 No. 2 (2004) Vol 19, No 1 (2004) Vol. 19 No. 1 (2004) Vol. 18 No. 2 (2003) Vol 18, No 2 (2003) Vol. 18 No. 1 (2003) Vol 18, No 1 (2003) Vol. 17 No. 3 (2002) Vol 17, No 3 (2002) Vol. 17 No. 2 (2002) Vol 17, No 2 (2002) Vol 17, No 1 (2002) Vol. 17 No. 1 (2002) Vol 16, No 3 (2001) Vol. 16 No. 3 (2001) Vol 16, No 2 (2001) Vol. 16 No. 2 (2001) Vol 16, No 1 (2001) Vol. 16 No. 1 (2001) Vol 16, No 1 (2001) Vol. 15 No. 3 (2000) Vol 15, No 3 (2000) Vol. 15 No. 2 (2000) Vol 15, No 2 (2000) Vol. 15 No. 1 (2000) Vol 15, No 1 (2000) Vol. 14 No. 3 (1999) Vol 14, No 3 (1999) Vol 14, No 2 (1999) Vol. 14 No. 2 (1999) Vol. 14 No. 1 (1999) Vol 14, No 1 (1999) Vol 13, No 3 (1998) Vol. 13 No. 3 (1998) Vol 13, No 2 (1998) Vol. 13 No. 2 (1998) Vol 13, No 1 (1998) Vol. 13 No. 1 (1998) Vol 12, No 3 (1997) Vol. 12 No. 3 (1997) Vol. 12 No. 2 (1997) Vol 12, No 2 (1997) Vol 12, No 1 (1997) Vol 12, No 1 (1997) Vol. 12 No. 1 (1997) Vol 11, No 3 (1996) Vol. 11 No. 3 (1996) Vol. 11 No. 2 (1996) Vol 11, No 2 (1996) Vol. 11 No. 1 (1996) Vol 11, No 1 (1996) Vol 10, No 1&2 (1994) Vol. 10 No. 1&2 (1994) Vol. 9 No. 1&2 (1990) Vol 9, No 1&2 (1990) Vol 8, No 1&2 (1989) Vol. 8 No. 1&2 (1989) Vol. 7 No. 1&2 (1988) Vol 7, No 1&2 (1988) Vol 6, No 1&2 (1987) Vol. 6 No. 1&2 (1987) Vol 5, No 1&2 (1986) Vol. 5 No. 1&2 (1986) Vol 4, No 3&4 (1985) Vol. 4 No. 3&4 (1985) Vol 4, No 1&2 (1985) Vol. 4 No. 1&2 (1985) Vol 3, No 2&3 (1984) Vol. 3 No. 2&3 (1984) Vol. 3 No. 4 (1984) Vol 3, No 4 (1984) Vol. 3 No. 1 (1984) Vol 3, No 1 (1984) Vol 2, No 2&3 (1983) Vol. 2 No. 2&3 (1983) Vol. 2 No. 4 (1983) Vol 2, No 4 (1983) Vol. 2 No. 1 (1983) Vol 2, No 1 (1983) Vol 1, No 1 (1982) Vol. 1 No. 1 (1982) More Issue