cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota semarang,
Jawa tengah
INDONESIA
GEMA TEKNOLOGI
Published by Universitas Diponegoro
ISSN : 08520232     EISSN : 2656582X     DOI : -
Core Subject : Science,
Gema Teknologi Journal (pISSN : 0852-0232, eISSN : 2656-582X) is an open access journal published by Vocational School, Diponegoro University, Indonesia. Gema Teknologi publishes articles from various engineering disciplines (the results of original scientific research or new scientific studies of literature). Editor receives articles both in English and Indonesian. Gema Teknologi Journal is published 2 (two) times a year, on April and October.
Arjuna Subject : -
Articles 217 Documents
Rancang Bangun Sistem Dosing Nutrisi Otomatis Berbasis ESP32 Menggunakan Kendali PID Adaptif dan Pemantauan IoT Fahren Diaz; Fakhruddin Mangkusasmito
Gema Teknologi Vol 23, No 1 (2024): April 2024 - October 2024
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v23i1.90336

Abstract

Nutrient management in modern hydroponic systems requires a high degree of precision to optimize plant growth. Controlling nutrient concentration levels in parts per million (PPM)—whether manually or using conventional on/off systems—is often inefficient and prone to causing overshoot. This study aims to design and build a prototype of an automated nutrient dosing system using an ESP32 microcontroller equipped with an adaptive Proportional-Integral-Derivative (PID) control algorithm and integrated with Internet of Things (IoT) technology. The system uses a Total Dissolved Solids (TDS) sensor to measure solution concentration, a DS18B20 temperature sensor for water temperature compensation, and three DC peristaltic pump actuators controlled via an L298N driver module using PWM signals. A heuristic gain scheduling (auto-tuning) algorithm was implemented so that the PID parameters could dynamically adjust their values based on the magnitude of the actual error. Test results showed that the adaptive PID method was able to respond quickly and settle stably without excessive overshoot. In a rise test with a setpoint of 400 PPM, the system achieved a rise time of 215.6 seconds with minimal overshoot of 0.20% and a steady-state error of 5.07 PPM. This system also proved resilient in handling sudden external disturbances in the form of added distilled water, with a recovery time of 96.5 seconds and a maximum overshoot of 5.00%. The integration of IoT infrastructure via the Blynk platform, automatic logging to Google Spreadsheets, and the presence of a Local Web Server successfully enabled users to monitor operations in real-time from a distance. It can be concluded that the design of this device effectively addresses the weaknesses of static control systems and provides high operational efficiency in hydroponic cultivation.
Rancang Bangun Oven Roti Elektrik Otomatis Berbasis Arduino Uno Dan Sensor Thermocouple Dengan Metode PID Taufika Hadya Rahma Dardila; Priyo Sasmoko
Gema Teknologi Vol 22, No 2 (2023): October 2022 - April 2023
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v22i2.90206

Abstract

In the food processing industry, particularly in bread production, ovens play a crucial role in achieving the desired product quality. The bread-baking process requires accurate and stable temperature control to ensure that the bread is baked evenly, cooked thoroughly, and possesses the intended texture. However, manual operation of an oven often leads to significant temperature fluctuations, which can compromise product quality and consistency. This study implements an Arduino Uno-based temperature control system for an automatic bread oven, utilizing a PID (Proportional-Integral-Derivative) control method. The PID method was selected for its ability to provide a rapid response, thereby ensuring a stable temperature. The system employs a heating element as an actuator and a thermocouple as a feedback sensor. Experimental results yielded PID parameters of Kp=0.5, Ki=3.8, and Kd=10. The system achieved the target set point of 150°C in 451 seconds (7 minutes and 31 seconds). The data indicates that temperature changes occur in a stable manner. Furthermore, once the system reaches the set point, the dimmer output decreases, though it does not shut off completely.
Rancang Bangun Pendeteksi Kebocoran Gas LPG (Liquefied Petroleum Gas) Berbasis Arduino Uno Menggunakan Sensor MQ-5 Dan Buzzer Kartika Hialdha Marel; Yuniarto Yuniarto
Gema Teknologi Vol 22, No 4 (2024): October 2023 - April 2024
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v22i4.90302

Abstract

Kartika Hialdha Marel 1), Yuniarto 2),  LPG gas leakage is one of the causes of fires and explosions that can endanger safety. This research aims to design and develop an LPG gas leakage detection system based on Arduino Uno using an MQ-5 sensor, buzzer, LEDs, and a 16x2 I2C LCD as warning and information media. The MQ-5 sensor is used to detect LPG gas concentration in Parts Per Million (PPM), then the data is processed by Arduino Uno to determine the system condition based on a predetermined threshold value. The system was tested under five conditions, namely no gas, low gas concentration, medium gas concentration, high gas concentration, and system response testing. The test results showed that under normal conditions the gas concentration remained within a safe range, while under high gas concentration conditions the system was able to detect concentrations up to 367.45 PPM and automatically activate the buzzer and blinking red LED when the concentration exceeded 200 PPM. Based on the test results, the system successfully operated according to the design in detecting LPG gas leakage and providing automatic early warning.
Prototype Pembangkit Dan Penyimpanan Energi Listrik Pada Sepeda Statis Anjassyafiq Wahyu Arrasyid; Arkhan Subari
Gema Teknologi Vol 21, No 4 (2022): October 2021 - April 2022
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v21i4.90290

Abstract

Efforts to utilize renewable energy can be enhanced by using alternative energy resources, such as motion power, one of which is a simple electricity generator from a stationary bike. The system utilizes pedaling motion, converted by a DC generator into battery charging. In this project, several developments were made, including charging efficiency, monitoring systems, energy accumulation, distance tracking, and a bonus system. The testing shows that the gear ratio affects RPM speed, proven by a rotation of 3000 at gear 5. Using gear 5, the power output at 3100 RPM reached 96.81W, with generator voltage at 21.3V, charging voltage at 14.26V, and current at 6.73A. Energy testing was conducted with four users pedaling for 5 minutes. The first user achieved an energy accumulation of 3.270 Wh, a bonus of Rp. 300, and a distance of 2146m. Test results for all four users are also presented in graph form for comparison. Parameters during the charging process can be monitored through the Arduino-based monitoring system.
Perancangan Alat Ukur Ketinggian Pada Kawat Trolley Kereta Listrik Menggunakan Sensor Ultrasonic Berbasis Arduino Uno Priandito Mukti Ramadhan; Yuniarto Yuniarto
Gema Teknologi Vol 21, No 3 (2021): April 2021 - October 2021
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v21i3.90270

Abstract

In an era of increasingly advanced transportation, the safety and efficiency of electric train operations is a top priority. To ensure safe and smooth operation, it is important to monitor the wire level on the electric train in real-time. This project proposes the design of a wire height meter that uses an ultrasonic sensor based on Arduino Uno as a solution for reliable wire height monitoring. This tool works by measuring the distance between the ultrasonic sensor and the wire on the electric train, then converting the distance data into the height of the wire. Arduino Uno is used as a microcontroller to control ultrasonic sensors and process data. Measurement results are displayed via an easy-to-understand user interface.
Rancang Bangun Alat Monitoring Breaker Motor 3 Fasa Berdasarkan Konfigurasi Breaker PLTU UBP Priok Dengan Pengukuran Keserempakan Serta Tegangan Secara Real-Time Berbasis Modul Optocoupler AC Serta Sensor ZMPT101B Dan Internet Of Things Melissa Rahmawati Yusuf; Eko Ariyanto
Gema Teknologi Vol 23, No 2 (2025): October 2024 - April 2025
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v23i2.90342

Abstract

This monitoring system was designed to automatically detect breaker status based on 24V DC voltage, utilizing a 25V DC sensor. The system is capable of transmitting real-time data with an average response time of 9 seconds. The ZMPT101B voltage sensor used in the setup demonstrated low error rates, with 0.97% for phase R, 0.91% for phase S, and 0.58% for phase T. Additionally, an AC optocoupler module was employed to detect 220V AC, enabling accurate synchronization measurement. Results indicate that synchronization during the "on" condition is highly accurate, although a slight delay was observed during the "off" condition due to residual current in the signal amplification transistor (S8050) located within the module. Testing at the Priok UBP Combined-Cycle Power Plant confirmed that the system meets the company's configuration standards, with an obtained the best value of 2 ms with average time of  3.2 ms, suggesting that the breakers operate within optimal parameters. Overall, the system performs effectively and aligns with the company’s operational requirements.
Prototype Pendeteksi Gangguan Dan Monitoring Arus Pada NH-FUSE Di PHB-TR Dilengkapi Data Logger Berbasis IoT (Internet Of Things) Prawira Duta Kusuma; Fakhruddin Mangkusasmito
Gema Teknologi Vol 22, No 1 (2022): April 2022 - Oktober 2022
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v22i1.90242

Abstract

A Low-Voltage Distribution Panel (PHB-TR) is a component within a Low-Voltage Distribution Network (JTR) that serves to connect, distribute, protect, and control electrical power downstream of a distribution transformer. The protection system within a PHB-TR utilizes NH-fuses as the primary protective device, acting as current limiters and safeguards against overcurrent conditions. According to reports from UP3 Purwokerto, faults within PHB-TR units remain a frequent occurrence. Furthermore, there have been numerous customer reports regarding prolonged response times for faults in the Low-Voltage Distribution Network, as technicians are often required to visit each site individually to perform maintenance. Consequently, there is a need for an innovation that enables PLN personnel to identify faults and monitor the status of PHB-TR units more effectively and efficiently. Data indicates that many PHB-TR faults are caused by damaged or blown NH-fuses that have not yet been replaced. This article addresses these issues by proposing a device for fault detection and current monitoring in PHB-TR NH-fuses, equipped with an IoT-based (Internet of Things) data logger. The device can transmit information to PLN personnel within 15–30 seconds of a fault occurring. It detects several types of issues: blown NH-fuses (when current exceeds the nominal rating), insulation breakdown (detected via input voltage at the fuse holder), and load imbalance during overcurrent conditions (exceeding a 20% variance between phases). When a fault is detected, an LED indicator illuminates, and personnel receive a notification via an application, accompanied by an audible alarm. The core components of this device include the PZEM-004T 10A (version 3) current and voltage sensor; an Arduino Mega 2560 microcontroller for data processing; a 20x4 LCD for real-time display of current and voltage values; and a MicroSD card module combined with an RTC (Real-Time Clock) for data logging. Additionally, an ESP8266 (NodeMCU) Wi-Fi module is integrated to transmit information regarding faults at the low-voltage distribution panel (PHB-TR) to the Blynk application. This device enables faster fault resolution at the PHB-TR, reduces operational maintenance costs, simplifies monitoring for PLN personnel, and improves the company’s performance metrics—specifically the Key Performance Indicators (KPIs) related to SAIDI and SAIFI. Furthermore, customers benefit from enhanced service, as power outages become less frequent and shorter in duration, ultimately strengthening PLN’s public image
Rancang Bangun Sistem Lampu UV Majemuk Dengan Metode Satu Tabung dan Sistem Pembersih Sleve Otomatis Pada Alat Sterilisasi Air Firstyawan Esa Naufalabib; Dista Yoel Tadeus
Gema Teknologi Vol 22, No 4 (2024): October 2023 - April 2024
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v22i4.90307

Abstract

Water sterilization using ultraviolet (UV) light is an effective method because it produces no chemical residues and involves a relatively simple process. However, the performance of UV systems can decline due to the buildup of contaminants on the surface of the lamp sleeves, while conventional systems generally lack both automatic cleaning mechanisms and integrated performance monitoring. This study aims to design and build a water sterilization device using multiple UV lamps in a single reactor tube equipped with an automatic sleeve cleaning system and IoT-based monitoring. The device was built using four 55W Germilite UV lamps arranged in a circular pattern inside a single acrylic reactor tube. The sleeve cleaning mechanism is driven by a NEMA17 stepper motor via a lead screw system, controlled by an ESP32 microcontroller with a user interface consisting of a 20x4 LCD, a rotary encoder, and a DS3231 RTC, as well as a data logging feature to Google Spreadsheet via Google Apps Script. Test results show that the quartz sleeve provides significantly better UV radiation transmission compared to the acrylic sleeve and approaches the conditions of a sleeve-less setup. The automatic cleaning system operated successfully for 38 cycles (±19 hours) before a mechanical failure occurred at the coupling connecting the stepper motor to the lead screw. The IoT monitoring system successfully transmitted all data without any packet loss, achieving a 100% success rate. Geometric analysis of the reactor using a line source model showed that the four-lamp configuration produced a total irradiance of 40.612 µW/cm² at the reactor’s center, four times higher than that of the single-lamp configuration.
Rancang Bangun Pintu Irigasi Otomatis Pada Lahan Persawahan Padi Menggunakan Sensor Water Level Ningrum Dwi Astuti; Saiful Manan
Gema Teknologi Vol 22, No 3 (2023): April 2023 - October 2023
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v22i3.90298

Abstract

Irrigation systems are one of the key factors in supporting agricultural productivity, particularly in rice paddies. This study aims to design an irrigation gate system capable of automatically regulating water flow. The system utilizes a water level sensor (float switch), a fuel sensor, a solenoid valve, a water pump, and an Arduino Uno microcontroller as the main control center, which provides HIGH and LOW digital logic signals to regulate the system’s operating conditions. Test results show that the designed prototype of the automatic water flow gate control system for rice paddy irrigation channels can detect water level conditions based on information from the water level sensor (float switch). When the maximum level is reached, the sensor sends a HIGH signal, which automatically closes the solenoid valve and shuts off the water pump. Conversely, when the rice paddy is dry or the water level reaches the minimum threshold, the system opens the solenoid valve—which acts as the irrigation gate—and activates the pump. This system has been able to operate stably in accordance with the irrigation needs of rice crops in the paddy fields, thereby making farmers’ work easier.
Rancang Bangun Sistem Pemantauan Kualitas Udara (CO2, NH3, Partikulat Debu PM2.5, Suhu, Dan Kelembapan) Dengan Sensor MQ 135, DHT22, Dan DSM501A Secara Real-Time Berbasis ESP32 Dan IoT Ermasa Cintana Indah Sitopu; Arkhan Subari
Gema Teknologi Vol 21, No 4 (2022): October 2021 - April 2022
Publisher : Vocational School Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/gt.v21i4.90286

Abstract

Declining air quality caused by human activities increases health risks, especially to the respiratory system. Gases like CO₂, NH₃, and fine particulate matter (PM2.5) are difficult to detect directly but pose significant health hazards, making real-time air quality monitoring systems necessary. This study designs a system based on ESP32 and IoT to measure the concentrations of CO₂, NH₃, PM2.5, temperature, and humidity in real-time using MQ135, DHT22, DSM501A sensors, and an RTC DS3231 module. Data is displayed on a dot matrix display and stored on the Arduino IoT Cloud platform. Testing shows that the system effectively monitors these parameters with good accuracy (sensor error rates: CO₂ 1.82%, temperature 3.33%, humidity 0%, PM2.5 8.17%). The system successfully provides accurate real-time data and facilitates further analysis, with potential for further development including automatic notification features and increased data logging capacity.