Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

International Journal of Electrical and Computer Engineering

IJECE
Website

Published by Institute of Advanced Engineering and Science

ISSN : 20888708 EISSN : 27222578 DOI : -

Core Subject : Science, Engineering,

Computer Science & IT Electrical & Electronics Engineering

International Journal of Electrical and Computer Engineering (IJECE, ISSN: 2088-8708, a SCOPUS indexed Journal, SNIP: 1.001; SJR: 0.296; CiteScore: 0.99; SJR & CiteScore Q2 on both of the Electrical & Electronics Engineering, and Computer Science) is the official publication of the Institute of Advanced Engineering and Science (IAES). The journal is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world.

Arjuna Subject : Ilmu Komputer (semua kategori) - Ilmu Komputer (Lain-Lain)

Articles 112 Documents

6 7 8 9 10

Search results for , issue "Vol 10, No 1: February 2020" : 112 Documents clear

Hybrid method for solving the non smooth cost function economic dispatch problem Wanchai Khamsen; Chiraphon Takeang; Patiphat Aunban
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

This article is focused on hybrid method for solving the non-smooth cost function economic dispatch problem. The techniques were divided into two parts according to: the incremental cost rates are used to find the initial solution and bee colony optimization is used to find the optimal solution. The constraints of economic dispatch are power losses, load demand and practical operation constraints of generators. To verify the performance of the proposed algorithm, it is operated by the simulation on the MATLAB program and tests three case studies; three, six and thirteen generator units which compared to particle swarm optimization, cuckoo search algorithm, bat algorithm, firefly algorithm and bee colony optimization. The results show that the proposed algorithm is able to obtain higher quality solution efficiently than the others methods.

Random forest age estimation model based on length of left hand bone for Asian population Mohd Faaizie Darmawan; Ahmad Firdaus Zainal Abidin; Shahreen Kasim; Tole Sutikno; Rahmat Budiarto
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

In forensic anthropology, age estimation is used to ease the process of identifying the age of a living being or the body of a deceased person. Nonetheless, the specialty of the estimation models is solely suitable to a specific people. Commonly, the models are inter and intra-observer variability as the qualitative set of data is being used which results the estimation of age to rely on forensic experts. This study proposes an age estimation model by using length of bone in left hand of Asian subjects range from newborn up to 18-year-old. One soft computing model, which is Random Forest (RF) is used to develop the estimation model and the results are compared with Artificial Neural Network (ANN) and Support Vector Machine (SVM), developed in the previous case studies. The performance measurement used in this study and the previous case study are R-square and Mean Square Error (MSE) value. Based on the results produced, the RF model shows comparable results with the ANN and SVM model. For male subjects, the performance of the RF model is better than ANN, however less ideal than SVM model. As for female subjects, the RF model overperfoms both ANN and SVM model. Overall, the RF model is the most suitable model in estimating age for female subjects compared to ANN and SVM model, however for male subjects, RF model is the second best model compared to the both models. Yet, the application of this model is restricted only to experimental purpose or forensic practice.

Fast photovoltaic IncCond-MPPT and backstepping control, using DC-DC boost converter Mohamed Moutchou; Atman Jbari
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

In this paper, we present our contribution in photovoltaic energy optimization subject. In this research work, the goal is to determinate fastly the optimal PV Module working point, allowing maximum power extraction. In this work we use DC-DC Boost converter to control the working point, by adjusting PV voltage trough duty cycle. In order to achieve our goal, we use the combination of incremental conductance MPPT technique and DC-DC Boost converter backstepping control. The validation of this control is made by Matlab simulation; the obtained results prove its effectiveness and its good maximum power tracking dynamics for different irradiance and temperature profiles.

An enhanced kernel weighted collaborative recommended system to alleviate sparsity S. Babeetha; B. Muruganantham; S.Ganesh Kumar; A. Murugan
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

User Reviews in the form of ratings giving an opportunity to judge the user interest on the available products and providing a chance to recommend new similar items to the customers. Personalized recommender techniques placing vital role in this grown ecommerce century to predict the users’ interest. Collaborative Filtering (CF) system is one of the widely used democratic recommender system where it completely rely on user ratings to provide recommendations for the users. In this paper, an enhanced Collaborative Filtering system is proposed using Kernel Weighted K-means Clustering (KWKC) approach using Radial basis Functions (RBF) for eliminate the Sparsity problem where lack of rating is the challenge of providing the accurate recommendation to the user. The proposed system having two phases of state transitions: Connected and Disconnected. During Connected state the form of transition will be ‘Recommended mode’ where the active user be given with the Predicted-recommended items. In Disconnected State the form of transition will be ‘Learning mode’ where the hybrid learning approach and user clusters will be used to define the similar user models. Disconnected State activities will be performed in hidden layer of RBF and Connected Sate activities will be performed in output Layer. Input Layer of RBF using original user Ratings. The proposed KWKC used to smoothen the sparse original rating matrix and define the similar user clusters. A benchmark comparative study also made with classical learning and prediction techniques in terms of accuracy and computational time. Experiential setup is made using MovieLens dataset.

Real time observer-based stator fault diagnosis for IM Khadidja El Merraoui; Abdellaziz Ferdjouni; M’hamed Bounekhla
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

This paper proposes a delta connected IM model that takes the Stator winding Inter-Turn Short Circuit (SITSC) fault into account. In order to detect the fault and evaluate its severity, an observer based FDI method is suggested. It allows the generation of residual using extended Kalman filter (EKF). To overcome the problem of the EKF initialization, the cyclic optimization method is applied to determine its tuning parameters. The advantage of the proposed approach is the real-time quantification of the fault severity and the quick fault detection. Using numerical simulation under both the healthy and the faulty conditions, the proposed IM model and EKF-based FDI approach are confirmed. Experimental results obtained by a real-time implementation on test-bench validate the simulated results.

PSS/E based placement wind/PV hybrid system to improve stability of Iraqi grid Nadheer A. Shalash; Yasar N. Lafta
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

Proper employment of Hybrid Wind/ PV system is often implemented near the load, and it is linked with the grid to study dynamic stability analysis. Generally, instability is because of sudden load demand variant and variant in renewable sources generation. As well as, weather variation creates several factors that affect the operation of the integrated hybrid system. So this paper introduces output result of a PV /wind via power electronic technique; DC chopper; that is linked to Iraqi power system to promote the facilitating achievement of Wind/ PV voltage. Moreover, PSS/E is used to study dynamic power stability for hybrid system which is attached to an effective region of Iraqi Network. The hybrid system is connected to Amara Old bus and fault bus is achieved to that bus and the stability results reflects that settling time after disturbance is not satisfactory. But, it is found that PV/wind generation system influences Iraqi grid stability to be better than that with only PV generation and the latter is better than stability of the grid that is enhanced with only wind generation. These results represent an important guideline for Iraqi power system planner.

Type 1 versus type 2 fuzzy logic speed controllers for brushless dc motors Hayder Yousif Abed; Abdulrahim Thiab Humod; Amjad J. Humaidi
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

This work presented two fuzzy logic (FL) schemes for speed-controlled brushless DC motors. The first controller is a Type 1 FL controller (T1FLC), whereas the second controller is an interval Type 2 FL controller (IT2FLC). The two proposed controllers were compared in terms of system dynamics and performance. For a fair comparison, the same type and number of membership functions were used for both controllers. The effectiveness of the structures of the two FL controllers was verified through simulation in MATLAB/SIMULINK environment. Simulation result showed that IT2FLC exhibited better performance than T1FLC.

Analytical study of flexible stimulation waveforms in muscle fatigue reduction E. Noorsal; S. Z. Yahaya; Z. Hussain; R. Boudville; M. N. Ibrahim; Y. Mohd Ali
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

This paper presents the analytical study of flexible stimulation waveforms in muscle fatigue reduction for functional electrical stimulator (FES)-assisted hemiplegic muscle activities. The major challenge of muscle contraction induced by FES is early muscle fatigue which greatly limits activities such as FES-assisted standing and walking. The fixed stimulation pattern applied on a same motor unit has resulted the motor unit to be overworked and fatigue easily. Therefore, in this work, the stimulus parameters, which include the pulse width duration and the frequency were varied to create a few flexible stimulation waveforms using MATLAB/Simulink. The pulse width duration was modulated from 100µs – 500µs to generate five types of flexible stimulation waveforms such as Rectangular, Trapezoidal, Ramp Up, Ramp Down and Triangular. Concurrently, a few ranges of stimulus frequency were also used, which include 20Hz, 30Hz and 50Hz. The generated flexible stimulation waveforms were applied onto a humanoid muscle model to investigate and analyse the muscle output response and early muscle fatigue reduction. From the conducted simulation results and analyses, it was observed that flexible stimulation waveforms such as Triangular, Ramp Up and Ramp Down could reduce early muscle fatigue phenomenon by having lower average of negative slope, in the range of 0.012 to 0.013 for the muscle fitness. In contrast, the Rectangular and Trapezoidal shapes were found to have higher negative slope of muscle fitness in the range of 0.028 to 0.031. The Ramp Down shape was found to have the lowest average of negative slope (0.012) while Rectangular was found to have the highest average of negative slope (0.031). Therefore, it can be concluded that flexible stimulation waveforms such Ramp Down, Ramp Up and Triangular shapes could reduce early muscle fatigue phenomenon with Ramp Down shape having the highest muscle fatigue reduction.

PSO-backstepping controller of a grid connected DFIG based wind turbine Salmi Hassan; Badri Abdelmajid; Zegrari Mourad; Sahel Aicha; Baghdad Abdenaceur
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

The paper demonstrates the feasibility of an optimal backstepping controller for doubly fed induction generator based wind turbine (DFIG). The main purpose is the extract of maximum energy and the control of active and reactive power exchanged between the generator and electrical grid in presence of uncertainty. The maximum energy is obtained by applying an algorithm based on artificial bee colony approach. Particle swarm optimization is used to select optimal value of backstepping’s parameters. The simulation is carried out on 2.4 MW DFIG based wind turbine system. The optimized performance of the proposed control technique under uncertainty parameters is established by simulation results.

A planar UWB semicircular-shaped monopole antenna with quadruple band notch for WiMAX, ARN, WLAN, and X-Band Majed O. Al-Dwairi
International Journal of Electrical and Computer Engineering (IJECE) Vol 10, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

This paper proposed quadruple notched frequency bands ultra-wideband (UWB) antenna. The antenna is a semicircular-shaped monopole type of a compact size 36x24 mm, covering frequency range of 3.02-14 GHz. Four rejected narrow bands including WiMAX (3.3-3.7GHz), ARN (4.2-4.5 GHz), WLAN (5.15-5.825GHz), X-Band (7.25-7.75) have been achieved using inserting slots techniques in the patch, feed line, and ground plane. The slots dimensions have been optimized for the required reject bands. The antenna design and analysis have been investigated by simulation study using CST-EM software package. The antenna characteristics including impedance bandwidth, surface current, gain, radiation efficiency, radiation pattern have been discussed.

Page 8 of 12 | Total Record : 112

6 7 8 9 10

Filter by Year

2020 2020

Filter By Issues

All Issue Vol 16, No 1: February 2026 Vol 15, No 6: December 2025 Vol 15, No 5: October 2025 Vol 15, No 4: August 2025 Vol 15, No 3: June 2025 Vol 15, No 2: April 2025 Vol 15, No 1: February 2025 Vol 14, No 6: December 2024 Vol 14, No 5: October 2024 Vol 14, No 4: August 2024 Vol 14, No 3: June 2024 Vol 14, No 2: April 2024 Vol 14, No 1: February 2024 Vol 13, No 6: December 2023 Vol 13, No 5: October 2023 Vol 13, No 4: August 2023 Vol 13, No 3: June 2023 Vol 13, No 2: April 2023 Vol 13, No 1: February 2023 Vol 12, No 6: December 2022 Vol 12, No 5: October 2022 Vol 12, No 4: August 2022 Vol 12, No 3: June 2022 Vol 12, No 2: April 2022 Vol 12, No 1: February 2022 Vol 11, No 6: December 2021 Vol 11, No 5: October 2021 Vol 11, No 4: August 2021 Vol 11, No 3: June 2021 Vol 11, No 2: April 2021 Vol 11, No 1: February 2021 Vol 10, No 6: December 2020 Vol 10, No 5: October 2020 Vol 10, No 4: August 2020 Vol 10, No 3: June 2020 Vol 10, No 2: April 2020 Vol 10, No 1: February 2020 Vol 9, No 6: December 2019 Vol 9, No 5: October 2019 Vol 9, No 4: August 2019 Vol 9, No 3: June 2019 Vol 9, No 2: April 2019 Vol 9, No 1: February 2019 Vol 8, No 6: December 2018 Vol 8, No 5: October 2018 Vol 8, No 4: August 2018 Vol 8, No 3: June 2018 Vol 8, No 2: April 2018 Vol 8, No 1: February 2018 Vol 7, No 6: December 2017 Vol 7, No 5: October 2017 Vol 7, No 4: August 2017 Vol 7, No 3: June 2017 Vol 7, No 2: April 2017 Vol 7, No 1: February 2017 Vol 6, No 6: December 2016 Vol 6, No 5: October 2016 Vol 6, No 4: August 2016 Vol 6, No 3: June 2016 Vol 6, No 2: April 2016 Vol 6, No 1: February 2016 Vol 5, No 6: December 2015 Vol 5, No 5: October 2015 Vol 5, No 4: August 2015 Vol 5, No 3: June 2015 Vol 5, No 2: April 2015 Vol 5, No 1: February 2015 Vol 4, No 6: December 2014 Vol 4, No 5: October 2014 Vol 4, No 4: August 2014 Vol 4, No 3: June 2014 Vol 4, No 2: April 2014 Vol 4, No 1: February 2014 Vol 3, No 6: December 2013 Vol 3, No 5: October 2013 Vol 3, No 4: August 2013 Vol 3, No 3: June 2013 Vol 3, No 2: April 2013 Vol 3, No 1: February 2013 Vol 2, No 6: December 2012 Vol 2, No 5: October 2012 Vol 2, No 4: August 2012 Vol 2, No 3: June 2012 Vol 2, No 2: April 2012 Vol 2, No 1: February 2012 Vol 1, No 2: December 2011 Vol 1, No 1: September 2011 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Tole Sutikno

Contact Email
ijece@iaesjournal.com

Phone
-

Journal Mail Official
ijece@iaesjournal.com

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Tole Sutikno

Contact Email ijece@iaesjournal.com

Phone -

Journal Mail Official ijece@iaesjournal.com

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Tole Sutikno

Contact Email
ijece@iaesjournal.com

Phone
-

Journal Mail Official
ijece@iaesjournal.com

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA