cover
Contact Name
Rahmat Azis Nabawi
Contact Email
raazna@ft.unp.ac.id
Phone
+6281277328670
Journal Mail Official
Syahril@ft.unp.ac.id
Editorial Address
Jl. Prof. Dr. Hamka Kampus UNP Air Tawar
Location
Kota padang,
Sumatera barat
INDONESIA
Teknomekanik
ISSN : 26219980     EISSN : 26218720     DOI : 10.24036/tm.
Core Subject : Engineering,
Teknomekanik is an international journal that publishes peer-reviewed research in engineering fields (miscellaneous) to the world community. Paper written collaboratively by researchers from various countries is encouraged. It aims to promote academic exchange and increase collaboration among scientists, engineers and researchers to support sustainable development goals.
Articles 182 Documents
Effects of loading angle and build direction on the tensile behavior of WAAM steel produced with ER70S-6 welding wire Nguyen Thien Nhut; Nguyen Tan No; Cao Le Anh Kiet; Nguyen Van Cuong
Teknomekanik Vol. 9 No. 3 (2026): Regular Issue
Publisher : Universitas Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24036/teknomekanik.v9i3.57472

Abstract

This study investigates the effects of loading angle and build direction on the tensile properties of components fabricated through wire arc additive manufacturing (WAAM) fabricated using ER70S-6 steel. Tensile tests were conducted at four loading angles (0°, 45°, 60°, and 90°) for two build directions (flat and upright). For each loading angle and build direction, two tensile specimens were tested, and the reported values were obtained from a representative specimen for each testing condition. The results reveal that the WAAM-fabricated specimens exhibited pronounced mechanical anisotropy, with the highest tensile strength obtained when the applied load is parallel to the bead direction, followed by a considerable reduction at other loading angles. For the upright build direction, the ultimate tensile strength decreased by approximately 47% at 450 relative to that at 0°, suggesting a possible contribution from interlayer shear stresses and delamination-related failure mechanisms. An empirical model was proposed to describe the dependence of tensile strength on the loading angle, enabling the quantitative evaluation of the role of different stress components. The flat build direction exhibited more stable mechanical behavior and a lower degree of anisotropy. In addition, hardness measurements showed that the variation in hardness was mainly governed by the build direction rather than the loading angle. The obtained results provide further insight into the relationship among layered structure, stress state, and mechanical properties, thereby supporting the design and application of WAAM structures subjected to multidirectional loading conditions.
Friction performance of palm oil-based trimethylolpropane ester containing bacterial cellulose and sorbitan monostearate: A Taguchi-based study Dedi Rosa Putra Cupu; Hairul Abral; Dedison Gasni; Zahrul Fuadi; Zulhanafi Paiman; Chong Wei Quan; Kahar Osman
Teknomekanik Vol. 9 No. 3 (2026): Regular Issue
Publisher : Universitas Negeri Padang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24036/teknomekanik.v9i3.59272

Abstract

Growing environmental concerns have prompted researchers to investigate renewable alternatives to mineral oils. Palm oil is a promising vegetable oil for use as a lubricant base stock due to its renewability, biodegradability, low environmental toxicity, and high viscosity. In this study, palm oil was chemically modified by a two-step esterification/transesterification process with trimethylolpropane (TMP) to yield palm oil-based TMP ester (PTMPE) as a base oil. Bacterial cellulose (BC) from nata de coco and sorbitan monostearate (Span 60) were incorporated into the base oil at different concentrations as an additive and a surfactant, respectively. Friction analysis was carried out using a four-ball tribotester at an elevated temperature. The Taguchi method was applied to optimize the experiment, with the mass fractions of BC and Span 60, as well as ultrasonication time, as input factors, and the coefficient of friction (COF) as the response. The results showed that the lowest COF was obtained when 0.3 wt% bacterial cellulose and 0.9 wt% Span 60 were added to the PTMPE ester and ultrasonicated for 10 minutes. In contrast to other studies that concentrated on water- or synthetic-based carriers, the friction-reducing performance of bacterial cellulose in PTMPE was investigated, resulting in a 16.45% decrease in COF under a 392 N load. Analysis of variance (ANOVA) showed that none of the investigated parameters were statistically significant in explaining variations in the coefficient of friction. However, the ultrasonication time had the largest estimated contribution among the investigated factors, accounting for almost 50%.