cover
Contact Name
Syah Alam
Contact Email
syah.alam@trisakti.ac.id
Phone
+6285710034984
Journal Mail Official
syah.alam@trisakti.ac.id
Editorial Address
Jl Kyai Tapa No.1
Location
Kota adm. jakarta barat,
Dki jakarta
INDONESIA
Jurnal Ilmiah Teknik Elektro
Published by Universitas Trisakti
ISSN : 2541089X     EISSN : 2541089X     DOI : https://doi.org/10.25105/jetri
Jetri is a scientific journal aims to publish high quality and up to date articles in electrical engineering field. Its scope includes (but not limited to): - Power Systems: nonrenewable and renewable energy power generation, power transmission and distribution, power conversion, protection system, electrical material, power system analysis, etc. - Telecommunications: modulation and signal processing for telecommunication, antenna and wave propagation, wireless and mobile communications, radar, satellite, communication network and systems, etc. - Control Systems: optimal controls, adaptive controls, non linear and stochastic controls, modeling and simulation, robotics, optimization, intelligent systems, fuzzy logic, etc. - Electronics: electronic materials, electronics system, microelectronic devices and system, VLSI, ASIC, system-on-a-chip (SoC), electronic instrumentations, medical electronics and instrumentation, etc. Computer Systems/Informatics: computer architecture, parallel processing, computer network, embedded system, human-computer interaction, virtual reality, computer security, machine learning and data mining, software
Articles 174 Documents
PERANCANGAN SISTEM BUKA-TUTUP KACA HELM OTOMATIS BERBASIS ARDUINO UNO Akbar Prakoso Wibowo; E. Shintadewi Julian
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 12, Nomor 2, Februari 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1121.671 KB) | DOI: 10.25105/jetri.v12i2.502

Abstract

Automatic open-close helmet visor based on Arduino Uno is a helmet that designed to protect motorcyclist from highly polluted air that may interrupt motorcyclist concentration. If the sensor detects air pressure up to a certain pressure, the sensor will send a signal to the Arduino Uno to drive the servo cover the glass helmet. As long as there is air pressure, the helmet visor will continue to close and will open again when the wind pressure is reduced. The main components used in the circuit design of automatic helmet are Arduino Uno, digital pressure sensor BMP085 as inputs and servo motors as output. After all of the devices are assembled and tested, the helmet with automatic open-close visor system with servo as output, works well as planned. The difference between the air pressure on barometer and the serial monitor is about 0.5%. Servo turning angle movement indicates a difference about 1° by the command in the program.Helm dengan sistem buka-tutup kaca otomatis berbasis Arduino Uno adalah sebuah helm yang dirancang untuk melindungi pengendara sepeda motor dari udara di Jakarta yang semakin kotor yang dapat mengganggu konsentrasi pengendara sepeda motor.Jika sensor mendeteksi tekanan angin sampai dengan tekanan tertentu, maka sensor akan mengirim sinyal ke Arduino Uno untuk menggerakkan servo menutup kaca helm. Selama ada tekanan angin, kaca helm akan terus menutup dan akan terbuka kembali pada saat tekanan angin berkurang. Komponen utama yang digunakan pada perancangan rangkaian helm otomatis ini adalah Arduino Uno, sensor tekanan digital BMP085 sebagai input dan motor servo sebagai output. Sesudah dirangkai dan diuji, helm dengan sistem buka-tutup kaca otomatis dengan output servo ini telah bekerja sesuai rancangan. Besar tekanan udara pada barometer dengan serial monitor terdapat perbedaan sebesar 0,5%. Sudut putar motor servo menunjukkan perbedaan sebesar 1° dengan perintah pada program.
MODEL SISTEM MONITORING TANGKI BAHAN BAKAR MINYAK SPBU DENGAN MENGGUNAKAN WEB APLIKASI DAN SMS GATEWAY Riki Ruly A. Siregar; Rifky Raymond
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 12, Nomor 2, Februari 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1183.354 KB) | DOI: 10.25105/jetri.v12i2.503

Abstract

The process of measuring gasoline container tanks in gas station or SPBU is one of the business activities conducted to manage the availability of the gasoline for customers. Usually, the measurement process is conducted manually by direct measurement or using mechanical method dipstick, so it is hard to get a good measurement result especially if the process conducted at night with lack of light. This research try to develop a telemetry system model to monitor the level of gasoline in the container tanks by integrating the use of Arduino microcontroller, ultrasonic sensors, temperature sensors LM35 with PHP programming language, Gammu SMS Gateway, Visual C# and utilizing wireless communication media. The system is tested to monitor the volume of fuel at the gas station through web based application program and integrated SMS gateway to provide information about the condition of the fuel tank when the fuel almost reached its lowest level.Proses pengukuran tangki bahan bakar minyak merupakan salah satu aktivitas dalam mengelola usaha stasiun pengisian bahan bakar minyak (SPBU). Pengukuran tangki bahan bakar minyak pada SPBU saat ini masih menggunakan metode mekanis dipstick atau pengukuran secara langsung secara manual, apalagi jika keadaan malam hari dengan kondisi penerangan sekitar kurang memadai yang kadang meyebabkan kesulitan dan ketidakakuratan pengukuran. Penelitian ini dibangun dengan memanfaatkan mikrokontroler Arduino, sensor ultrasonic, sensor suhu LM35, bahasa pemrograman PHP, Gammu SMS Gateway dan Visual C# serta memanfaatkan media komunikasi wireless untuk membangun sebuah sistem Telemetri. Melalui penelitian ini diperoleh sebuah sistem yang dapat digunakan untuk memonitor volume bahan bakar minyak pada SPBU berbasis web aplikasi, dan terintegrasi dengan sms gateway untuk memberikan infomasi kondisi bahan bakar minyak pada tangki BBM apabila BBM hampir mencapai level terendah.
ANALISIS PERANCANGAN SISTEM PROTEKSI BANGUNAN THE BELLAGIO RESIDENCE TERHADAP SAMBARAN PETIR Maula Sukmawidjaja; Syamsir Abduh; Shahnaz Nadia
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 12, Nomor 2, Februari 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (632.907 KB) | DOI: 10.25105/jetri.v12i2.504

Abstract

High rise building is one of the objects that have the possibility of being struck by lightning considering geographical location of Indonesia which in equator, resulted in rainfall and intensity of lightning strikes is quite high. Hence it is important to protect high rise  buildings with a reliable system such as Electric Field  Lightning Protection System (E.F Lightning Protection System). This system is more active due to the addition of the charge induced lightning rod from the earth's surface. This protection system has 150,597.54 m2 wide protection area by E.F terminals. The 35mm2 conductor dealer (E.F Carrier) carry high voltage with additional dealer conductor. The distance between lighting rods is 38.73 meters.  The first resistance grounding is 1.72Ω and the second resistance is 2.32Ω. The result shows thet the system already meets standards for ng buildings protection.Bangunan tinggi merupakan salah satu objek yang memiliki kemungkinan besar tersambar petir mengingat letak geografis Indonesia yang dilewati garis khatulistiwa yang mengakibatkan curah hujan dan intensitas sambaran petir cukup tinggi. Oleh karena itu penting untuk memproteksi bangunan tinggi dengan sistem yang handal seperti Electric Field Lightning Protection System (E.F Lightning Protection System). Sistem ini bersifat lebih aktif karena adanya penambahan muatan pada ujung penangkal petir yang diinduksi dari permukaan bumi. Sistem proteksi ini memiliki daerah proteksi cukup luas sebesar 150.597,54 m2 yang dihasilkan oleh E.F Terminal sehingga dapat memproteksi seluruh area gedung. Konduktor penyalur (E.F Carrier) yang digunakan berdiameter 35 mm2 dapat menerima tegangan tinggi namun harus diadakan penambahan konduktor penyalur. Jarak antara kedua penangkal 38,73 m. Tahanan pembumian 1 sebesar 1,72 Ω, tahanan pembumian 2 sebesar 2,32 Ω. Dari hasil perhitungan sistem ini sudah memenuhi standar untuk memproteksi bangunan tinggi.
ANALISIS TERJADINYA TEKANAN MENDADAK PADA ON LOAD TAP CHANGER UNIT 1 PLTU SURALAYA Muhamad Yanuardi Putra; Chairul Gagarin Irianto
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 12, Nomor 2, Februari 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (531.096 KB) | DOI: 10.25105/jetri.v12i2.505

Abstract

Sudden pressure that exceeds the normal pressure in the transformer insulating oil is due to the decomposition of dissolved gases caused by sparks. To determine the content of dissolved gases, the Total Dissolved Combustible Gas (TDCG) and the Duval Triangle method are used. Examination of the Suralaya Unit 1 UST transformer condition with the transport-X on 10 and 11 November 2014 showed a trend of rising TDCG 818.60; 858.80 and 825.80 respectively, which are still in a state of mild warning. For further analysis the Duval Triangle method is used for the three gases i.e. methane (CH4), acetylene (C2H2), and Ethylene (C2H4). The results show that in Unit 1 UST tap changer has occurred sparks, which is related to 7.62% CH4; 76.73% C2H2; and 15.64% C2H4 that was in the D1 area on the Duval Triangle. Because the sudden pressure and spark is caused by C2H2, the increase of C2H2 gas should be prevented.Tekanan mendadak yang melampaui tekanan normal pada minyak isolasi transformator terjadi akibat dekomposisi gas terlarut yang disebabkan percikan api. Untuk mengetahui kandungan gas terlarut digunakan metode Total Dissolved Combustible Gas (TDCG) dan Segitiga Duval. Pemeriksaan dengan Transport-X pada tanggal 10 dan11 November 2014, menunjukkan bahwa kondisi tap changer di transformator UST Unit 1 PLTU Suralaya menunjukkan kecenderungan kenaikan TDCG masing-masing 818,60; 858,80 dan 825,80; yang masih dalam kondisi peringatan ringan. Untuk analisis lebih lanjut digunakan metode Segitiga Duval untuk gas metana (CH4), asetilen (C2H2), dan etilen (C2H4). Dari hasil analisis diketahui bahwa pada tap changer UST Unit 1 telah terjadi percikan api. Titik pada Segitiga Duval menunjukkan nilai 7,62% pada sumbu CH4; 76,73% pada sumbu C2H2; dan 15,64% pada sumbu C2H4 yaitu berada di daerah D1. Hal ini menunjukkan bahwa yang menimbulkan percikan dan tekanan mendadak adalah gas C2H2 oleh sebab itu  kenaikan gas C2H2 pada tap changer UST Unit 1 PLTU Suralaya perlu dicegah. 
RANCANG BANGUN ALAT PEMBANGKIT EFEK SURROUND DENGAN IC BUCKET-BRIGADE DEVICE (BBD) MN 3008 Albert Mandagi
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 12, Nomor 2, Februari 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (493.85 KB) | DOI: 10.25105/jetri.v12i2.506

Abstract

Surround Effects Generator with Bucket-Brigade device (BBD) MN 3008 IC is a device that is realized in order to have the ability to produce a reverberation effect by using delay time. The circuit consists of a buffer amplifier, pre amplifier, low pass filter I, bucket-brigade device (BBD) MN 3008 IC, ramp generator, voltage controlled oscillator, summing amplifier I, low pass filter II and summing amplifier II. In this device, the sound effects are generated by delaying the input signal using an analog delay time channel component IC BBD MN 3008 which has as many as 2048 level specification delay, and the delay time up to 102.4 ms. By using this surround effects generator, voice reverberation can be generated with an adjustable delay time of 10.5 ms - 15.5 ms that will produce voice that is wider and more lively and as if the listeners are in spacious room.Pembangkit Efek Surround Dengan IC Bucket-Brigade Device (BBD) MN 3008 adalah suatu perangkat yang direalisasikan agar memiliki kemampuan untuk menghasilkan efek reverberasi dengan menggunakan saluran tunda. Rangkaian ini terdiri dari penguat penyangga, penguat depan, tapis lulus bawah I, IC bucket-brigade device (BBD) MN 3008, generator ramp, osilator terkendali tegangan, penguat penjumlah I, tapis lulus bawah II, penguat penjumlah II. Pada alat ini, efek suara dihasilkan dengan cara menunda sinyal masukan menggunakan saluran tunda IC analog BBD MN 3008 yang memiliki spesifikasi sebanyak 2048 tingkat tunda, dengan waktu tunda sampai 102,4 ms. Dengan menggunakan pembangkit efek surround ini, dapat dibentuk suara reverberasi dengan waktu tunda yang dapat diatur dari 10,5 ms - 15,5 ms sehingga akan dihasilkan suara yang lebih lebar dan lebih hidup dan seakan-akan pendengar berada pada ruangan yang luas.
MODEL VEKTOR TEGANGAN DALAM MODULASI VEKTOR RUANG 3-DIMENSI PADA FILTER AKTIF SISTEM TIGA-FASA Indriarto Yuniantoro; Ishak Kasim
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 13, Nomor 1, Agustus 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (477.579 KB) | DOI: 10.25105/jetri.v13i1.564

Abstract

Anelectric current flow on the neutral wire give raise to harmonics. It is a problem that must be solved one of which is space vector modulation technique. A few voltage vector models have been developed including by Zhang and Perales. In this paper the models are compared to determine reference voltage vector and duty cycle, developed asymmetric’s model based on Akagi theory too. The results show that asymmetric’s model can be proposed as a new technique in space vector modulation.Arus yang mengalir pada kawat netral menimbulkan harmonisa. Hal itu merupakan masalah yang harus diselesaikan salah satunya adalah dengan teknik modulasi vektor ruang. Beberapa model vektor tegangan telah dikembangkan diantaranya oleh Zhang dan Perales. Dalam tulisan ini dibandingkan model-model tersebut dalam menentukan vektor-tegangan referensi dan duty cycle. Dikembangkan pula model asimetri yang berdasarkan pada teori Akagi. Hasilnya menunjukkan bahwa model asimetri dapat diusulkan sebagai satu teknik baru dalam modulasi vektor ruang.
PERHITUNGAN PENURUNAN UMUR TRANSFORMATOR AKIBAT PENGARUH SUHU LINGKUNGAN Adhie Satrya Gianto; Chairul Gagarin Irianto; Darto Gianto
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 13, Nomor 1, Agustus 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (396.005 KB) | DOI: 10.25105/jetri.v13i1.565

Abstract

The normal transformer lifespan can not be ascertained due to various causes, among others, the operating / different loading and ambient temperature factors. The life expectation of transformer will be achieved if distribution transformer is operated with continuously loaded at room temperature 20 °C and winding temperature 98 °C. The transformer which is operated in Indonesia with 30 °C room temperature will decrease thecapacity of the normal lifespan to 91%. From the calculation of loading, in accordance with the characteristics of thermal obtained from the transformer type test, although the transformer is designed to operate at an ambient temperature of 20 °C but operated at a temperature of about 30 °C, it turns out there are several types of transformers that do not decrease the capacity of the lifetime. Transformer number 2, 3, 4, and 5 despite decrease the capacity can still be operated above 91%. So in order to obtain optimal loading, we must know the thermal characteristics of each transformer that is obtained from the results of thetype test.Umur normal transformator tidak dapat dipastikan karena bemacam-macam penyebab antara lain pada faktor operasi/pembebanan yang berbeda dan kondisi suhu sekitar. Umur harap transformator akan tercapai bila transformator distribusi dioperasikan dengan pembebanan yang kontinu pada suhu ruang 20 °C dan kenaikan suhu belitan 98 °C, tetapitransformator yang dioperasikan di Indonesia yang mempunyai suhu ruang sekitar 30 °C akan mengalami penurunan kapasitas menjadi 91% dari umur normalnya. Dari hasil perhitungan pembebanan, sesuai dengan karakteristik termal yang didapat dari hasil uji jenis transformator, walaupun transformator tersebut dirancang untuk beroperasi pada suhu sekitar 20 °C tetapi dioperasikan pada suhu sekitar 30 °C, ternyata ada beberapa jenis transformator yang tidak mengalami penurunan kapasitas umur. Transformator nomor 2, 3, 4 dan 5 walaupun mengalami penurunan kapasitas masih dapat dioperasikan di atas 91%.Jadi untuk mendapatkan pembebanan yang optimal, harus mengetahui karakteristik termal masing–masing transformator yang didapat dari hasil uji jenis. 
PEMULIHAN ARUS GANGGUAN PADA SKTM 20 KV DENGAN MENGGUNAKAN FASILITAS GROUND FAULT DETECTOR (GFD) 3G Jecklin Praspa Dewi; Syamsir Abduh
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 13, Nomor 1, Agustus 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (198.806 KB) | DOI: 10.25105/jetri.v13i1.566

Abstract

One of the main tasks of the electricity industry is to provide reliable electricity to customers. Supply interruptions are less and less accepted by customers and society mainly because their socioeconomic effects are increasingly severe. Reliability of supply and its value are key factors for the decision making process underlying expansion plans not only of electricity generation systems but also of transmission and distribution networks. To meet these demands, the PLN use reliable distribution technology, i. e. 3G Ground Fault Detector (GFD). This paper aims to analyze the use of 3G GFD. The secondary data were obtained from the substation Setiabudi Jakarta. The results showed that use of 3G GFD can speed maneuverability and long outages of 143.06 minutes to 34.25 minutes and reduce the number of unsold kWh amounting to 76.06%.Salah satu tugas utama perusahaan listrik adalah menghasilkan tenaga listrik yang dapat diandalkan oleh pelanggan. Gangguan pasokan listrik semakin tidak dapat ditolerir oleh pelanggan karena dampak sosial dan ekonomi yang sangat berat. Keandalan pasokan merupakan salah satu faktor kunci dalam pengambilan keputusan untuk pengembangan sistem pembangkit, transmisi dan distribusi tenaga listrik. Untuk memenuhi tuntutan tersebutPLN menggunakan teknologi distribusi yang bisa diandalkan kualitasnya, yaitu Ground Fault Detector (GFD) 3G. Pada tulisan ini dikemukakan analisis penggunaan GFD 3G dengan menggunakan data sekunder dari Gardu Induk Setiabudi Jakarta. Dari hasil analisis diketahui bahwa penggunaan GFD 3G dapat mempercepat waktu manufer gangguan dan lama padam dari 143,06 menit menjadi 34,25 menit serta mengurangi jumlah kWh tak terjual sebesar 76,06%. 
ALAT STERILISASI KERING DENGAN KUNCI OTOMATIS BERBASIS MIKROKONTROLER Kiki Prawiroredjo; Calvin Renato
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 13, Nomor 1, Agustus 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (263.997 KB) | DOI: 10.25105/jetri.v13i1.567

Abstract

Dry Sterilizer with Automatic Lock Door Based on Microcontroller ATMEGA16A is a machine to sterilize surgical instruments. This sterilizer equips with an automatic solenoid locking door system that controlled by a temperature sensor. When the temperature inside the chamber is above 37 °C, the door will remain locked, because the temperature is higher than the temperature of the human body. When the temperature is 37 °C the door willautomatically open. Microcontroller ATMEGA16A as a controller sets the length of time of sterilization process and controls the work process of temperature sensors, solenoids, heater, LCD and relay. The results show that the heating process takes 5 minutes to reach 120 °C and the cooling process requires 15 minutes to reach 37 °C.Alat Sterilisasi Kering dengan Pengunci Otomatis Berbasis Mikrokontroler ATMEGA16A adalah sebuah pemanas yang berfungsi sebagai peralatan untuk mensterilkan instrumen-instrumen bedah. Pengunci otomatis pada bagian pintu alat sterilisasi menggunakan kunci solenoid yang menutup dan membukanya diatur oleh sebuah sensor temperatur. Ketikatemperatur di dalam ruangan pemanas di atas 37 °C atau lebih panas dari temperatur tubuh manusia maka pintu alat sterilisasi akan tetap terkunci. Pada saat temperatur sudah mencapai 37 °C maka pintu akan otomatis terbuka. Mikrokontroler ATMEGA16A sebagai pemroses akan mengatur lama waktu proses sterilisasi, serta mengatur proses kerja sensor temperatur, solenoid, pemanas, LCD dan relay. Setelah diuji ternyata pemanasanmembutuhkan waktu rata-rata 5 menit untuk mencapai temperatur 120 °C. Proses pendinginan memerlukan waktu rata-rata 15 menit untuk mencapai temperatur 37 °C. 
LAMPU LALU LINTAS UNTUK PENYEBERANG JALAN Kuat Rahardjo T.S.; Sunarto Tan; Endang Djuana
Jetri : Jurnal Ilmiah Teknik Elektro Jetri Volume 13, Nomor 1, Agustus 2015
Publisher : Website

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (282.639 KB) | DOI: 10.25105/jetri.v13i1.568

Abstract

Traffic lights for pedestrians are necessary to provide security and comfort for pedestrians and vehicle drivers in order to avoid accidents and traffic jams. During the design of the circuit, component selection analysis was performed for assembling the controller. The analysis showed that the industrial timer has the ease of setting intervals and ease of maintenance controller in the case of damage. The testing on the design showed that, aftercrossing demand button was pressed, the traffic lights worked well in one cycle to allow pedestrians and further provides the opportunity for passing vehicles until the crossing demand button was pressed again by a pedestrian.Lampu lalu lintas untuk penyeberang jalan, merupakan hal yang dibutuhkan untuk memberikan rasa aman dan nyaman bagi pejalan kaki maupun pengemudi kendaraan untuk menghindari terjadinya kecelakaan dan kemacetan lalu lintas. Dalam perancangan rangkaian dilakukan analisis pemilihan komponen untuk merakit kontroler. Analisis menunjukkan bahwa Timer industri memiliki kemudahan dalam melakukan pengaturanselang waktu dan kemudahan dalam perawatan kontroler jika terjadi kerusakan. Pengujian atas perancangan menunjukkan, setelah penekanan tombol permintaan menyeberang, lampulalu lintas bekerja baik sesuai satu siklus untuk memberi kesempatan penyeberang jalan, dan selanjutnya memberi kesempatan untuk kendaraan melintas sampai tombol permintaanmenyeberang ditekan oleh penyeberang selanjutnya.

Page 2 of 18 | Total Record : 174