cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Hadziqul Abror
Contact Email
hadziqulabror@unej.ac.id
Phone
+6282140986802
Journal Mail Official
jurnal_jsed@unej.ac.id
Editorial Address
Program Studi Teknik Perminyakan, Fakultas Teknik, Universitas Jember Jl. Kalimantan Tegalboto No.37, Krajan Timur, Sumbersari, Kec. Sumbersari, Kabupaten Jember, Jawa Timur 68121.
Location
Kab. jember,
Jawa timur
INDONESIA
Journal of Sustainable Energy Development
Published by Universitas Jember
ISSN : -     EISSN : 30482585     DOI : -
Core Subject : Science, Engineering,
Energy Engineering
The Journal of Sustainable Energy Development is the official scientific journal of Petroleum Engineering, Faculty of Engineering, University of Jember for the dissemination of information on research activities, technology engineering development and laboratory testing in sustainable energy development. The focus and scope of JSED as follows: Oil and Gas Technology: Production, Reservoir, and Drilling Technology, Enhance Oil Recovery Geothermal Technology: Reservoir Characterization and Modeling, Development of Productivity-Enhancing Methods, Plan of Vevelopment Earth Science: Geology, Geophysics, Geochemical Renewable Energy: Wind energy, Hydro energy, Solar cell energy, Biomass
Arjuna Subject : Energi (semua kategori) - Energi Terbarukan, Keberlanjutan dan Lingkungan
Articles 23 Documents
 1   2   3 
Carbon Capture Utilization (CCU) sebagai Generator Energi Listrik menggunakan Allam Cycle sebagai Upaya Dekarbonisasi Industri Migas Izzati, Fifi; Ababil, Pijar Fitrah; Abror, Hadziqul
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Along with the development and progress of human civilization, the need for electrical energy continues to increase. For this reason, new energy sources are needed so that energy needs can be met. Carbon dioxide (CO2) can be a new energy source obtained from industrial waste energy processing. CO2 is a type of emission that can cause the formation of greenhouse gas (GHG) emissions and contributes to global climate change. A 6% increase in emissions from 2020 results in emissions of 36.3 giga tons (Gt). One utilization of CO2 emissions that can be done is to convert CO2 emissions into electricity. The data analysis method is done by comparing the technical and economic parameters between the rankine power cycle using H2O as the working fluid and the Allam power cycle using CO2 as the working fluid. The results obtained are that the natural gas-fired Allam cycle has a net HHV and LHV efficiency of 53.17% and 58.90%, respectively. For the coal-fired Allam cycle, the net HHV and LHV efficiencies obtained were 48.88% and 51.44%, respectively. The economic analysis conducted is LCOE, IRR, and NPV. The economic analysis shows that the project is feasible in terms of electricity cost.
EKSTRAKSI LITIUM PADA AIR FORMASI PANAS BUMI DENGAN METODE ADSORPSI (STUDI KASUS PADA PLTP DIENG) Ababil, Pijar Fitrah; Mahendra, Faroucki Seven; Faiqotul Hikmah; Lilo Al Fiqriansyah; Nanda Wulansari
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Geothermal energy is produced due to the tectonic and volcanic activity of a hydrothermal system in the earth. Geothermal potential in Indonesia is 28,170 MW, but only 1728 MW or 4% of the geothermal potential is utilized as a source of Geothermal Power Plant (GPP). The development of GPP requires a very large investment and is not comparable to the selling price of electricity. The principle of GPP is to use hot steam from the reservoir to generate electricity through a generator. The produced fluid consists of steam and brine water which will later be discharged/reinjected. Brine water comes from meteoric water that settles around the reservoir rocks. This precipitation process will dissolve minerals in the reservoir rock, one of which is lithium which is the raw material for batteries. There are various methods to extract lithium from brine water, including precipitation, ion-exchange, extraction with ion-in-liquids (ILs), and adsorption. The lithium extraction process begins with brine that is adsorbed using Li-ion-sieves and will be eluted with dilute HCl and then precipitated with Na2CO3 to become LiCO3 which will be marketed as battery raw material. The brine at Dieng GPP has a lithium content of 50.11 to 99.4 mg/L in the brine, if the flow rate is 70 tons/hour, 1.89 tons/month of LiCO3 will be obtained.
Analisa Model Machine Learning dalam Memprediksi Laju Produksi Sumur Migas 15/9-F-14H Devy Ayu Rhamadhani; Saputra, Eriska Eklezia Dwi
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

AI algorithm learns various data streams from various sources sensors and engines to extract the analytics resulting in sound advice smart based on business needs. This deep insight makes it possible for oil and gas companies to have better visibility of the whole process and operations, thereby enabling them to make strategic decisions better. This of course leads to increased operating efficiency, cost reduction, and even reduce the risk of failure. Application of artificial intelligence using machine learning to production of oil and gas wells needs to be done to get predictive results perfect. With the support of existing field data so obtained simulation results that provide an overview of the prediction of production wells can optimizing the implementation of production performance for wells that have same production history. The simulation is carried out using the development of machine learning models, Support Vector Regression (SVR), Elastic Net, dan Linear Regression. The data which contains informations about the well production will be divided into two parts, 70% for training and 30% for testing. Of the three models will be seen which one is the best in predicting the production rate of the well 15/9-F-14H based on the RMSE and R2 score. SVR is the best model for predicting oil by producing RMSE 5.48 and R2 0.88 when testing. Elastic-Net is the best model for predicting gas by producing RMSE 966.82 and R2 0.85 when testing. There is no model that fits to predict the water production.
Desain dan Analisa Electrical Submersible Pump Pada Lapangan P-N 62 Sebagai Upaya Peningkatan Produksi Lestari, Nila Khoirul Tria; Abror, Hadziqul
Journal of Sustainable Energy Development Vol. 2 No. 1 (2024): Journal of Sustainable Energy Development (JSED)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.19184/jsed.v2i1.308

Abstract

The reservoir pressure in the P-N oil well is currently showing a significant decline. Some oil wells cannot flow naturally, so artificial lift is required to maintain Jabung oil production and deplete the remaining oil reserves. Analysis and evaluation of the use of artificial lift electrical submersible pump (ESP) in the P-N62 well using calculation and simulation to see the production performance of a well after adding artificial lift based on the results of the calculation it is determined that the ESP TD800 Series-400 with 117 stages with the ability to produce up to 990.96 BFPD and has an efficiency of 58.67% which will be used to increase the production rate at the P-N62 well. Keywords: artificial lift; electrical submersible pump (ESP); Inflow Performance Relationship; petroleum
Analisis Potensi Sumur dan Peramalan Keadaan Sumur Dimasa Depan Dengan Menggunakan Metode Wiggins pada Sumur FS-09ST Lapangan Sukowati Faroucki Seven Mahendra; Hadziqul Abror
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Production of the FS-09ST well began on January 17th, 2009 with oil production is 401 BOPD and peak production on May 13th, 2011 with oil production is 3254 BOPD. Over time, production has decreased until the well was shut-in on October 9th, 2020 with oil production is 11 BOPD due to the high watercut which reached 99.55%. The location of this research is administratively located in Campurejo Village, Bojonegoro District, Bojonegoro Regency. Analysis of well potential and well forecasting was carried out using the Wiggins method based on well test data conducted on November 10th, 2020. This method is used because the FS-09ST well has three-phase fluid and a high water cut. The results of the analysis show that the maximum flowrate is 3899.44 BFPD, the optimum flowrate is 2340 BFPD, and a recommended production flowrate is 2340 BFPD at flowing bottom hole pressure (Pwf) is 1240 Psi to avoid water coning. Based on forecasting future IPR, it is known that the economic limit rate of this well is when the reservoir pressure is 1965 Psi with a oil flowrate of 10.08 BOPD.
Tinjauan Komprehensif Evaluasi Potensi Penerapan Enhanced Geothermal System Lanjutan: Fracking dan Hydroshearing Adam Dwi Putra; Putri Rizkika Ramadhanti Pedraza; Riska Laksmita Sari
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Indonesia merupakan negara dengan potensi panas bumi yang besar, dengan posisi negara yang terletak di cincin vulkanik menjadi Indonesia sebagai negara yang memiliki banyak tempat sumber panas bumi. Sumber panas bumi merupakan energi terbarukan yang dapat dikelola menjadi energi listrik, akan tetapi dalam proses produksinya masih banyak tantangan dan kendala dalam pengembangan energi panas bumi ini. Pada pengembangannya dibutuhkan metode yang efektif dalam menangani masalah yang ada dan mengoptimalkan produksi energi panas bumi. Penelitian ini ditujukan untuk membahas dan mereview salah satu metode peningkatan produksi energi panas bumi yaitu metode enhanced geothermal system (EGS). Metode stimulasi EGS dapat mengatasi beberapa kendala seperti permeabilitas kecil dan dapat memproduksi energi panas bumi pada hot dry rock (HDR). Pada EGS diterapkan fracking untuk memperbesar permeabilitas, hydroshearing juga dapat diterapkan pada EGS. Penelitian ini dilakukan dengan metode studi literatur dan mengumpulkan data dari beberapa artikel penelitian terdahulu yang berhubungan dengan EGS. Berdasarkan studi literatur, metode EGS sudah banyak diterapkan di beberapa negara di dunia. Indonesia juga sudah mulai melakukan penelitian mengenai penerapan metode EGS ini yang dilakukan di lapangan Kamojang dan Dieng. Keywords: Enhanced Geothermal System, EGS, Fracking, Hydroshearing
Pengembangan Teknologi Supercritical Geothermal: Potensi dan Strategi untuk Energi Bersih dan Berkelanjutan Dian Pertiwi, Permata; Riska Laksmita Sari; Fauji Islami Phasya
Journal of Sustainable Energy Development Vol. 2 No. 1 (2024): Journal of Sustainable Energy Development (JSED)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.19184/jsed.v2i1.342

Abstract

Development of supercritical geothermal technology is a complex and challenging process that requires significant investment in research, technology development, and collaboration. However, the potential benefits of this technology include low carbon footprint, high efficiency, and the potential to provide reliable electricity, making it an important focus area for the future of clean energy production. This study is qualitative and uses literature study methods involving data collection and analysis from various literature sources, including scientific journals, books, and reports. The literature study was conducted by searching and collecting several relevant and accurate sources such as scientific journals, books, and official publications on the topic. Data collection was carried out by analyzing the content of each available source. The supercritical geothermal well drilling method can generate electricity of 3-5 MW per well. Several successful energy development projects include exploration well drilling in Mexico, Italy, Iceland, USA, Kenya, and Japan. Supercritical energy development technology is also continuously being developed, such as closed-loop and CO2 utilization. The development of supercritical geothermal technology is a complex and challenging process that requires significant investment in research, technology development, and collaboration. However, the potential benefits of this technology include low carbon footprint, high efficiency, and the potential to provide reliable electricity, making it an important focus area for the future of clean energy production.   Keywords: energy; geothermal; supercritical; technology; development; efficiency
Analisis Mutu Briket Berbahan Baku Campuran Ampas Teh dan Sekam Padi Menggunakan Perekat Molase Menggunakan Metode Pirolisis Zeni Ulma; Nur Faizin; Reynadi Febri Afiandi
Journal of Sustainable Energy Development Vol. 1 No. 1 (2023)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This study aims to anayze the effect of molasses adhesive composition on the quaity of briquettes made from tea dregs and rice husks and to determine the characteristics of tea dregs and rice husk briquettes using molasses adhesive. The research was carried out through severa stages, namely the preparation of raw materias, drying of raw materias, pyrolysis of rice husks and tea dregs, raw materias mashed with a 40 mesh sieve, mixing of molasses adhesive, printing, drying and testing the characteristics of briquettes. The pyrolysis process takes 1 hour for the preparation of rice husks and 1.5 hours for the preparation of tea dregs with no or little air. The results showed that the best composition was TSM2 with a ratio of 30% tea dregs and 70% rice husks. The results of the study with the best composition, namely TSM2, caorific vaue 3771 ca/g, moisture content 9.28%, ash content 6.92%, density 1.16 g/cm3, kamba density 0.49 g/cm3, combustion rate 0.031 g/ s. TSM1 10% tea dregs charcoa and 90% rice husk charcoa caorific vaue 3399 ca/g, moisture content 8.94%, ash content 8.02%, density 1.51 g/cm3, kamba density 0.53 g/cm3, burning rate of 0.049 g/s and TSM3 50% tea dregs charcoa and 50% rice husk charcoa caorific vaue 4192 ca/g, moisture content 9.98%, ash content 6.85%, density 0.86 g/cm3, kamba density 0.43 g/cm3, the combustion rate is 0.025 g/s.
ANALISIS PERBANDINGAN PRODUKSI SEBELUM DAN SETELAH WELLSERVICE PADA SUMUR X LAPANGAN Y PT PERTAMINA EP Yehuda Eric Christian; Laksmita Sari, Riska
Journal of Sustainable Energy Development Vol. 2 No. 1 (2024): Journal of Sustainable Energy Development (JSED)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.19184/jsed.v2i1.498

Abstract

Well X started production on February 9th, 2012 with oil production of 217 BOPD and peak production on March 1th, 2012 with oil production of 2756 BOPD. As production progresses, the reservoir pressure will decrease resulting in a decrease in the production rate. Well X was shut-in on March 7th, 2023 with oil production of 197 BOPD and watercut reaching 91.27%. The location of this study is administratively located in Campurejo Village, Bojonegoro District, Bojonegoro Regency. Analysis of well potential and well forecasting are carried out by the Wiggins method. This method was chosen because the X well has a three-phase fluid and a high water cut. The calculation results show a maximum flow rate of 4111.52 BFPD and an optimum flow rate of 2466.91 BFPD. After calculating the optimum flow rate, and to avoid water cloning, it is recommended that wells be produced with a production flow rate of 2412.54 BFPD at a well base flow pressure (Pwf) of 1368 Psi. Keyword: well service; IPR; future IPR
Optimasi Jaringan Pipa Sumur ESP Pada Manifold A dan Manifold Satelite untuk Meningkatkan Laju Aliran Minyak dan Analisis Perubahan Tekanan di Lapangan J Pedraza, Putri Rizkika Ramadhanti; Ayuningtyas, Rivanya; Eriska Eklezia Dwi Saputri; Hadziqul Abror
Journal of Sustainable Energy Development Vol. 2 No. 1 (2024): Journal of Sustainable Energy Development (JSED)
Publisher : Petroleum Engineering, Faculty of Engineering, University of Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.19184/jsed.v2i1.499

Abstract

The wells in Field J, using Electrical Submersible Pumps (ESP), have replaced their natural flow operations. To optimize this ESP well and pipeline network, the research focuses on adjusting the ESP pump frequency within the Pipesim simulator, increasing it to enhance oil flow rates. This study employs a quantitative approach, where field data is analyzed and input into a simulation model that replicates real-world conditions. The analysis encompasses changes in flow rates and pressures, comparing the base case to post-optimization simulations. The results indicate a substantial increase in the initial oil flow rate from 578 STB to 720 STB/d, with an increase of 142 STB/d, when the pump frequency is raised to 60 Hz. This frequency adjustment significantly boosts pump discharge pressure, providing the added energy needed to transport fluid to the surface. Keyword: esp; pipeline network; production optimization; production simulation

Page 1 of 3 | Total Record : 23

 1   2   3 

Filter by Year

2023 2025


Reset
Filter By Issues
All Issue Vol. 3 No. 1 (2025): Journal of Sustainable Energy Development (JSED) Vol. 2 No. 2 (2024): Journal of Sustainable Energy Development (JSED) Vol. 2 No. 1 (2024): Journal of Sustainable Energy Development (JSED) Vol. 1 No. 1 (2023)