cover
Contact Name
Dr. rer.nat. Muldarisnur
Contact Email
-
Phone
+6282387463421
Journal Mail Official
jfu@sci.unand.ac.id
Editorial Address
Jurusan Fisika, FMIPA, Universitas Andalas ,Kampus Unand Limau Manis Padang 25163
Location
Kota padang,
Sumatera barat
INDONESIA
Jurnal Fisika Unand
Published by Universitas Andalas
ISSN : 23028491     EISSN : 26862433     DOI : https://doi.org/10.25077/jfu
Makalah yang dapat dipublikasikan dalam jurnal ini adalah makalah dalam bidang Fisika meliputi Fisika Atmosfir, Fisika Bumi, Fisika Intrumentasi, Fisika Material, Fisika Nuklir, Fisika Radiasi, Fisika Komputasi, Fisika Teori, Biofisika, ataupun bidang lain yang masih ada kaitannya dengan ilmu fisika.
Articles 40 Documents
Search results for , issue "Vol 9 No 1 (2020)" : 40 Documents clear
Analisis Kurva Profile Dose Menggunakan Lapangan Radiasi Elektron pada Pesawat LINAC Tipe Clinac-Cx di Rs Unand Sumitra, Nanang; Milvita, Dian; Kanie, Muhammad Al Jabbar
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.73-78.2020

Abstract

Telah dilakukan analisis kurva profile dose menggunakan lapangan radiasi elektron pada pesawat LINAC tipe Clinac-CX di RS Unand. Penelitian ini menggunakan berkas elektron energi 9, 12, 15,18 MeV pada lapangan radiasi no off-set, off-set 1 cm, off-set 3 cm yang bertujuan untuk mengetahui pengaruh energi dan lapangan radiasi terhadap nilai symmetri, flatness dan penumbra. Hasil penelitian menunjukkan bahwa nilai symmetry dan flatness pada tiap energi dan lapangan radiasi masih dalam batas toleransi yang ditetapkan oleh AAPM TG-40 yaitu 3%. Begitu juga dengan nilai penumbra yang diperoleh masih dalam batas toleransi yaitu (10-15) mm. Research on the analysis of profile dose curves has been carried out using electron radiation fields on LINAC Clinac-CX type aircraft at Unand Hospital.  This study uses electron beam energy 9, 12, 15.18 MeV using a radiation field no off-set, off-set 1 cm, off-set 3 cm which aims to determine the effect of energy and radiation field on the symmetry, flatness and penumbra values. The results showed that the symmetry and flatness values in each energy and radiation field were still within the tolerance limits set by the AAPM TG-40 at 3%. As well the penumbra value obtained is still within the tolerance range of 10-15 mm.
Analisis Kecocokan Nilai Percepatan Tanah Pulau Lombok Berdasarkan Perhitungan Empiris dengan Data Percepatan Tanah dari Akselerograf di Stasiun Mataram Saputri, Diana; Pujiastuti, Dwi
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.79-84.2020

Abstract

Telah dilakukan perhitungan nilai percepatan tanah Pulau Lombok yang divalidasi dengan nilai percepatan tanah di Stasiun Mataram.  Percepatan tanah dihitung dengan beberapa rumusan empiris, yaitu Mc. Guire, Fukushima-Tanaka, Esteva dan Donovan.  Data gempa yang digunakan adalah data gempa bumi di Pulau Lombok dan sekitarnya pada periode 1979-2018.  Hasil validasi menunjukkan rumusan Fukushima adalah rumusan terbaik untuk menghitung percepatan tanah di Pulau Lombok dengan persentase kesalahan rata-rata terendah 220%, sedangkan rumusan lainnya memiliki persentase kesalahan rata-rata Mc. Guire 2.586%, Esteva 614%, dan Donovan 3.906%.  Berdasarkan hasil yang diperoleh maka rumusan Fukushima-Tanaka adalah rumusan yang paling cocok untuk menghitung nilai percepatan tanah di Pulau Lombok. The calculation of Lombok Island ground acceleration values which are validated with the value of acceleration of the land at Mataram Stationhas been carried out.  Land accelerationis calculated by several empirical formulations,  namely Mc. Guire, Fukushima-Tanaka, Esteva and Donovan.Earthquake data used is earthquake data on the Lombok Islandand its surrounding in the periode 1979-2018. Validation result show thatFukushima-Tanaka is the best formula for calculating the acceleration of land on the Lombok Island with the average percentage error 220%, while the other formulations have an average percentage error Mc. Guire 2.586%, Esteva 614%, and Donovan 3.906%. Based on the result obtained, the formula Fukushima-Tanaka is the most suitable formula for calculating the value of land acceleration on the Lombok Island.
Analisis Solusi Spatial dan Temporal Persamaan NLS (Nonlinear Schrödinger) Sebagai Solusi Soliton Menggunakan Metode DVR (Discrete Variable Representation Maulana, Irvan; Abdullah, Zulfi
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.85-92.2020

Abstract

Analisis solusi persamaan Schrödinger Nonlinear (NLS) dengan menggunakan metode Representasi Variabel Diskrit (DVR) telah dilakukan. Penggunaan metode DVR ini dilakukan dengan mengkontruksikan fungsi basis melalui interpolasi Lagrange dan koefisien spektral yang berdasarkan polinomial Chebyshey pada titik Chebyshev-Gauss-Lobatto (CGL). Hasil simulasi dari metode DVR ini memiliki bentuk yang sama dengan 2 jenis solusi eksak persamaan NLS yaitu Cubic Nonlinear Schrödinger (CNLS) dan Generalized Nonlinear Schrödinger (GNLS), namun memiliki rentang penjalaran yang berbeda. Perbedaan rentang tersebut dikarenakan adanya kondisi awal yang ditetapkan pada metode DVR ini. Penggunaan metode DVR pada pengkondisian CNLS menghasilkan bentuk soliton onsite, sedangkan pada pengkondisian GNLS dihasilkan bentuk soliton onsite namun memiliki amplitudo yang berbeda pada setiap perubahan posisi dan waktu. Analysis of Nonlinear Schrödinger (NLS) equation by using Discrete Variable Representation (DVR) method has been carried out. The DVR method done with built basic function from Lagrange interpolation and spectral coefficient from Chebyshev polynomial in Chebyshev-Gauss-Lobatto (CGL) point. The result of DVR method simulation has same form with 2 type of exact solution of NLS equation are Cubic Nonlinear Schrödinger (CNLS) and Generalized Nonlinear Schrödinger (GNLS), however the result has different distance of propagation. That difference distance caused by initial condition which set on this method. The using of DVR method in CLNS condition produce soliton onsite form, but for GNLS condition produce soliton onsite form too but it has different amplitude for every change of position and time.
Pemanfaatan Data Alos PALSAR Untuk Etimasi Pergerakan Tanah Kota Padang Upaya Mitigasi Bencana Longsor Ckhotimah, Husnul; Vonnisa, Mutya; Budiman, Arif
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.93-99.2020

Abstract

Telah dilakukan penelitian untuk mendeteksi besar pergerakan tanah sebagai faktor pendorong penyebab terjadinya bencana longsor di Kota Padang.  Penelitian ini menggunakan data penginderaan jauh yakni data citra ALOS PalSAR tahun 2008 sampai 2009.  Metode yang digunakan dalam pengolahan adalah Differential Interferometry Synthetic Radar (DInSAR). Metode ini dapat mengamati pergerakan tanah terutama pada daerah perbukitan dengan ketelitian sentimeter.  Hasil penelitian menunjukkan besar pergerakan tanah untuk wilayah di Kota Padang berkisar antara 0,33- 3,04 cm/tahun.  Dari 11 kecamatan di Kota Padang, lima diantaranya yakni Kecamatan Pauh, Padang Selatan, Bungus Teluk Begalung, Koto Tangah dan Kuranji mengalami pergerakan atau pergeseran tanah yang cukup besar dari kecamatan lainnya yakni berkisar antara 0,825- 2,31 cm/tahun. Besarnya pergerakan tanah tersebut menyebabkan lima kecamatan di atas sering mengalami bencana tanah longsor dengan kategori cukup rawan. Research has been conducted to detect the magnitude of land movement as a driving factor for the occurrence of landslides in the city of Padang. This study uses remote sensing data namely ALOS PalSAR image data from 2008 to 2009. The method used in processing is Differential Interferometry Synthetic Radar (DInSAR). This method can observe the movement of the soil, especially in hilly areas with sub-centimeter accuracy. The results showed the amount of land movement for the area in Padang City ranged from 0,33 to 3,04 cm /year. Of the 11 districts in the city of Padang five of them namely the District of Pauh, South Padang, Bungus Teluk Begalung, Koto Tangah and Kuranji experienced substantial land movements or shifts from other districts which ranged from 0,825 to 2,31 cm /year. The magnitude of land movements and the high level of rainfall causes the five districts often experience landslides in quite vulnerable categories.
Optimisasi Ukuran Teras High Temperature Gass-cooled Reactor (HTGR) dengan Daya 30 MWt Tipe Pebble Bed Berbasis Bahan Bakar Uranium Armanita, Desi; Fitriyani, Dian; Setiadipura, Topan
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.100-109.2020

Abstract

Telah dilakukan optimasi ukuran teras Reaktor daya Eksperimental (RDE). Optimasi ini bertujuan untuk memperoleh ukuran teras yang optimal untuk RDE 30 MWt berdasarkan aspek neutronik antara lain discharge burn up, fuel residence time dan distribusi daya dan aspek keselamatan. Pada tahap awal dilakukan optimasi pass bahan bakar. Pass bahan bakar menyatakan jumlah sirkulasi bahan bakar ke teras reaktor dan parameter optimasi pass adalah nilai power peaking factor mendekati 1, discharge burn up tinggi serta memiliki temperatur puncak bahan bakar setelah DLOFC rendah. Berdasarkan parameter tersebut didapatkan pass optimal adalah 5 pass. Variasi ukuran teras ditentukan dengan dua cara, yaitu variasi ukuran teras pada volume tetap dan variasi tinggi teras pada diameter tetap. Tahap selanjutnya, terhadap ukuran teras yang optimal, dilakukan optimasi fraksi enrichment dan heavy metal loading bahan bakar. Dari hasil perhitungan diperoleh bahwa pada volume tetap (5 m3) parameter-parameter neutronik bernilai optimal jika ukuran diameter teras 1,5 m dan tinggi 2,83 m, sedangkan pada diameter teras tetap (1,8 m) parameter-parameter neutronik optimal pada ukuran tinggi teras 3,931 m.  Pada kedua ukuran teras ini aspek keselamatan, discharge burn up dan fuel residence time optimal pada enrichment 17% dan heavy metal loading 6 grU/pebble. Core size optimization of Experimental Power Reactor (EPR) has been done. This optimization aims to obtain the optimal core size for the RDE 30 MWt based on the neutronik aspect among other discharge burn ups, fuel residence time, power distribution and safety aspect. In the early stages the fuel pass optimization is done. The fuel pass is the amount of fuel circulation to the reactor core and the pass optimization parameter is the value of power peaking factor approaching 1, high discharge burnup as well as having a fuel peak temperature after DLOFC is low. According to the parameters, the optimal pass is 5 passes. The variation in the size of the core is determined in two ways, which is the core size variation on fixed volumes and a high variation of the core at fixed diameter. The next stage, against the optimal core size, carried out the optimization of the fraction of enrichment and heavy metal loading fuel.  From the results of the calculations obtained that on a fixed volume (5 m3) neutronik parameters are optimal if the size of the core diameter is 1.5 m and height 2.83 m, while on the fixed diameter of the ratio (1.8 m) The optimal neutronik parameters of on the size Height of core 3.931 m.  On both of these core sizes are safety aspects, discharge burn up and fuel residence time is optimal on the enrichment of 17% and heavy metal loading 6 grU/pebble.
Analisis Dosis Radiasi Paru-Paru Pasien Kanker Payudara dengan Teknik Three Dimensional Conformal Radiation Therapy (3D-CRT) Berdasarkan Grafik Dose Volume Histogram (DVH) Febrietri, Ovia; Milvita, Dian; Diyona, Fiqi
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.110-117.2020

Abstract

Telah dilakukan analisis dosis radiasi pada paru-paru enam orang pasien kanker payudara yang mendapat terapi radiasi sinar-X 6 MV dengan teknik penyinaran Three-Dimensional Conformal Radiation Therapy (3D-CRT). Penelitian ini bertujuan untuk memenuhi asas optimasi dan limitasi dalam proteksi radiasi dengan mengevaluasi dosis radiasi yang diterima target kanker berdasarkan ICRU Report 62, dan dosis yang diterima paru-paru pasien kanker payudara berdasarkan QUANTEC, serta mengetahui efek yang ditimbulkan pasca terapi. Pengambilan data dilakukan pada hasil kurva Dose Volume Histogram (DVH) yang didapatkan dari perencanaan penyinaran oleh dokter dan fisikawan medis di Rumah Sakit Universitas Andalas. Hasil penelitian yang didapatkan pengobatan pasien memenuhi asas optimasi karena mendapatkan dosis radiasi yang maksimal pada daerah target kanker. Nilai dosis radiasi yang diterima paru-paru pada tiga orang pasien tidak memenuhi asas limitasi karena melebihi aturan yang ditetapkan oleh QUANTEC, dan salah satu dari pasien mengalami pneumonitis. Hasil evaluasi dosis radiasi pada Planning Target Volume (PTV) dan paru-paru yaitu dosis radiasi yang diterima paru-paru pasien melebihi aturan QUANTEC dan menjadi salah satu risiko terjadinya pneumonitis. Radiation doses in the lungs of six breast cancer patients who received 6-MV X-ray radiation therapy with the Three Dimensional Conformal Radiation Therapy (3D-CRT) radiation technique has been analysed. This study aims to fulfill the principles of optimization and limitation in radiation protection by evaluating the radiation dose received by the cancer target based on ICRU Report 62, and the dose received by the breast cancer patient's lungs based on QUANTEC, as well as knowing the effects caused post-therapy. Data collection was performed on the results of the Dose Volume Histogram (DVH) curve obtained from radiation planning by doctors and medical physicists at Andalas University Hospital. The results of the study found that the treatment of patients fulfills the principle of optimization because they get the maximum radiation dose in the cancer target area. The value of the radiation dose received by the lungs in three patients did not meet the limitation principle because it exceeded the rules set by QUANTEC, and one of the patients had pneumonitis. The results of the radiation doses on the Planning Target Volume (PTV) and lungs, is the radiation dose received by the patient's lungs exceeds the QUANTEC rule and increases the risks of pneumonitis.
Analisis Kecocokan Nilai Percepatan Tanah Kota Padang Panjang-Bukittinggi Berdasarkan Perhitungan Secara Empiris dengan Data Percepatan Tanah dari Akselerograf yang Terpasang Di Stasiun Padang Panjang Oktaviani, Violina; Pujiastuti, Dwi
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.118-124.2020

Abstract

Telah dilakukan perhitungan nilai percepatan tanah Kota Padang Panjang-Bukittinggi menggunakan data gempa bumi dari Segmen Sianok dan sekitarnya. Perhitungan dilakukan dengan persamaan empiris yang divalidasi dengan data percepatan tanah dari akselerograf yang terpasang di Stasiun Padang Panjang. Rumusan empiris yang digunakan adalah Mc.Guire, Fukushima-Tanaka, Esteva, Donovan, dan Kanai. Hasil validasi menunjukkan bahwa rumusan Esteva merupakan rumusan paling cocok  digunakan untuk Kota Padang Panjang-Bukitting dengan persentase kesalahan rata-rata sebesar 73%, sedangkan 4 rumusan lainnya mempunyai persentase kesalahan rata-rata masing-masing Mc.Guire 581%, Fukushima-Tanaka 79%, Donovan 514%, dan Kanai 191%. The calculation peak ground acceleration (PGA) of Padang Panjang-Bukittinggi using the earthquake data from the Sianok Segment and its surroundings. Calculations are carried out from several empirical equations which are validated with ground acceleration data from accelerographs installed at Padang Panjang Station. Empirical formulations were use Mc.Guire, Fukushima-Tanaka, Esteva, Donovan, dan Kanai. Validation results show that the Esteva formula is the most suitable formula for the City of Padang Panjang-Bukittinggi with the average error percentage of 73%, while the other 4 formulas have an average error percentage of each Mc.Guire 581%,Fukushima-Tanaka 79%, Donovan 514%, dan Kanai 191%.
Karakterisasi Sensor Liquefied Petroleum Gas (LPG) Dari Bahan Komposit SnO2-ZnO Mardaleni, Mardaleni; Elvaswer, Elvaswer
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.125-133.2020

Abstract

Telah dilakukan karakterisasi sensor gas LPG berbentuk pelet dari bahan komposit SnO2 dengan ZnO. Pelet sensor gas LPG dibuat dengan komposisi yang berbeda dengan perbandingan SnO2 dan ZnO yaitu 90%:10% mol, 70%:30% mol, 50%:50% mol, 30%:70% mol, 10%:90% mol, 100% mol SnO2, dan 100% mol ZnO. Pembuatan sensor gas LPG diawali dengan pencampuran bahan, kalsinasi pada suhu 500 oC selama 4 jam, penggerusan, kompaksi dan sintering pada suhu 700 oC selama 4 jam dengan menggunakan reaksi dalam keadaan padat. Sensor gas LPG diuji pada suhu ruang untuk mendapatkan karakteristik I-V, menghitung nilai sensitivitas, selektivitas, konduktivitas, waktu respon dan karakterisasi XRD. Berdasarkan pengukuran karakteristik I-V, sensitivitas tertinggi pada sampel 30% mol SnO2 + 70 % mol ZnO yaitu 4,74 pada tegangan 24 Volt. Nilai selektivitas tertinggi terdapat pada sampel 50% mol SnO2 + 50% mol ZnO yaitu 2,31 pada tegangan 24 volt. Nilai konduktivitas tertinggi dimiliki sampel 30% mol SnO2 + 70 % mol ZnO yaitu 12,32 x 10-4/Ω.m pada lingkungan LPG. Waktu respon sampel  30% mol SnO2 + 70 % mol ZnO yaitu 48 s pada tegangan 24 Volt. Hasil XRD menunjukkan ukuran kristal 30% mol SnO2 + 70% mol ZnO yaitu 53,20 nm lebih kecil dibandingkan dengan 100% ZnO dan 100% SnO2 yaitu 54,48 nm dan 53,21 nm. Characterization of LPG gas sensor in the form of pellets made of SnO2 and ZnO composite was perfomed. LPG sensor pellets were made with a different composition with the ratio of SnO2 and ZnO are 90%:10% mol, 70%:30% mol, 50%:50% mol, 30%:70% mol, 10%:90% mol, 100% mol SnO2, dan 100% mol ZnO. The making of LPG gas sensors begins with mixing of material, calcining at 500 oC for 4 hours, grinding, compacting and sintering at 700 oC for 4 hours using solid state reaction method. LPG gas sensors was tested at room temperature by measuring the characteristics I-V, calculating sensitivity, selectivity, conductivity, response time and morphology. The highest sensitivity was obtained the sample 30% mol SnO2 + 70% mol ZnO is 4.74 at a voltage of 24 volts. The highest selectivity was obtained the sample 50% mol SnO2 + 50% mol ZnO is 2.31 at a voltage of 24 Volts. The highest conductivity value was given a sample of 30% mol SnO2 + 70% mol ZnO is 12.32 x 10-4 / Ω.m in the LPG environment. The response time of the sample is 30% mol of SnO2 + 70% mol of ZnO which is 48 s at a voltage of 24 Volts. The XRD results that the crystallite size of 30% mol SnO2 + 70% ZnO is 53.20 nm smaller than 100% ZnO and 100% SnO2 is 54.48 nm and 53.21 nm.
Rancang Bangun Pendeteksi Beban Berlebih pada Tas Ransel Sekolah Berbasis Arduino Uno dengan Sensor Load Cell Putri, Femilia; Wildian, Wildian
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.134-141.2020

Abstract

Telah dirancang alat pendeteksi beban berlebih pada tas ransel berbasis Arduino Uno dengan sensor load cell dengan kapasitas maksimum 5 kg. Mikrokontroler pada Arduino Uno R3 akan memproses data dengan menggunakan bahasa pemograman Arduino IDE. Input dari sistem adalah berat badan yang diinput dari keypad dan beban tas yang diukur langsung oleh sensor load cell. Sensor load cell akan mengalami perubahan resistansi saat diberi beban. Selanjutnya perubahan resistansi dikonversi ke tegangan oleh modul HX711. Tegangan kemudian diubah menjadi massa yang ditampilkan pada LCD (Liquid Crystal Display). Ketika beban tas melebihi berat 10% dari massa pengguna maka LCD akan menampilkan keterangan “Beban Berlebih” dan buzzer akan berbunyi sebagai peringatan. Hasil penelitian menunjukkan bahwa alat yang dirancang memiliki akurasi sebesar 99,79% dibandingkan dengan timbangan digital. Nilai tersebut diperoleh dengan kondisi beban yang diberikan bervariasi dari 500 g sampai 5000 g. Overload detector for backpack based on Arduino Uno with load cell sensor has been designed with a maximum capacity of 5 kg. The microcontroller on Arduino Uno R3 will process data using the Arduino IDE programming language. The input of the system is the weight input from the keypad and the bag load which is measured directly by the load cell sensor. Load cell sensors will experience resistance changes when under load. Then the change in resistance is converted to voltage by the HX711 module. The voltage is then converted to the mass displayed on the LCD (Liquid Crystal Display). When the bag load exceeds the weight of 10% of the mass of the user, the LCD will display the statement "Beban Berlebih" and the buzzer will sound as a warning. The results showed that the system designed had an accuracy of 99.79% compared to digital scales. This value is obtained with the given load conditions varying from 500 g to 5000 g.
Three-State Quantum Heat Engine Based on Carnot Cycle Sutantyo, Trengginas Eka Putra
Jurnal Fisika Unand Vol 9 No 1 (2020)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jfu.9.1.142-149.2020

Abstract

In this paper,we consider three models of quantum heat engines based on Carnot cycle using three energy levels; (1) the ground state, (2) the degenerate state, and (3) the highest energy state. We investigate the variation in the transition state by selecting three different degenerated states. The result we obtained still analogous with the classical heat engine efficiency and also the previous Quantum Carnot Engine model, which only depends on the initial width and the final width of the potential well in isothermal expansion. Moreover, the effect of transition state generally can be accepted for multistate quantum heat engines with 3D systems in cubic potential.

Page 4 of 4 | Total Record : 40