Claim Missing Document
Check
Articles

Found 2 Documents
Search

Design and Performance Evaluation of a Motor-Driven Adjustable Speed Tool for Corrosion Removal on Bolt Threads in Steam Power Plant Applications Kadex Widhy Wirakusuma; Agus Salim Opu; Yudi Siswanto; Angga Tegar Setiawan; Eriek Aristya Pradana Putra; Muhammad Alfian; Hendi Lilih Wijayanto; Abdul Malik Alfafa
Jurnal Teknologi dan Manajemen Vol. 24 No. 1 (2026): Jurnal Teknologi dan Manajemen (February)
Publisher : Politeknik STMI Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.52330/jtm.v24i1.523

Abstract

This study presents the design, fabrication, and experimental evaluation of a portable motor-driven adjustable-speed tool for localized corrosion removal on bolt threads in steam power plant maintenance. The prototype combines a variable-speed motor, a rotating wire brush, and a clamping fixture to ensure controlled contact with threaded surfaces. Performance was assessed on corroded bolts (M14 × 60 mm and M16 × 60 mm) at four spindle speeds (450, 900, 1350 and 1800 rpm), recording cleaning time, vibration, and surface temperature. Results show a strong inverse relationship between motor speed and cleaning time; for example, M16 bolts were cleaned in 1.37 minutes at 450 rpm and 0.36 minutes at 1800 rpm. A time-based cleaning efficiency metric peaked at higher speeds for the tested bolt sizes, while higher rpm also increased vibration and surface temperature, indicating an operational trade off. Compared with manual brushing, the prototype delivered faster, more uniform cleaning with reduced operator dependency and lower thread abrasion. An operational range of 1350–1800 rpm is recommended to balance effectiveness and mechanical/thermal constraints. Future work should include quantitative image-based area removal and gravimetric validation to corroborate surface integrity and material removal rates for field deployment.
Cellulose Nanofiber-Reinforced PVA Films Incorporated with Moringa oleifera Leaf Extract: Mechanical, UV-Shielding, and Structural Properties Kadriadi Kadriadi; Agus Salim Opu; Kadex Widhy Wirakusuma; Kamaruddin Kamaruddin; Jefry Jamel; Jeri Ariksa; Angga Bahri Pratama; Muhammad Adlan Azka
Journal of Fibers and Polymer Composites Vol. 5 No. 3 (2026): Journal of Fibers and Polymer Composites
Publisher : Green Engineering Society

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55043/jfpc.v5i3.728

Abstract

Polymer films that combine mechanical durability with ultraviolet (UV) protection are needed for sustainable packaging. In this study, polyvinyl alcohol (PVA) films reinforced with cellulose nanofibers (CNF) and incorporated with Moringa oleifera leaf extract (MLE) were prepared by solution casting at combined loadings of 1–4 wt% CNF and 0.5–2 wt% MLE. The tensile properties, UV–visible transmittance, and crystalline structure of the films were evaluated, and the tensile data were analyzed by one-way ANOVA followed by Duncan’s multiple range test (p < 0.05). Tensile strength and tensile modulus increased significantly with increasing CNF–MLE loading. The P-CNF4/MLE2 film exhibited the highest tensile strength (75.47 ± 2.89 MPa) and tensile modulus (654.04 ± 14.96 MPa), corresponding to increases of 118.4% and 116.8%, respectively, relative to neat PVA. Although elongation at break decreased at the lowest loading, both elongation at break and toughness increased at higher loadings, reaching 334.43 ± 6.90% and 227.96 ± 15.43 MJ m⁻³, respectively, for P-CNF4/MLE2. All composite films strongly attenuated UV radiation; films containing at least 2 wt% CNF and 1 wt% MLE transmitted less than approximately 1% of the incident light across the 200–400 nm range, whereas visible-light transmittance at 600 nm decreased from approximately 92% for neat PVA to 45% for P-CNF4/MLE2. X-ray diffraction confirmed that the semicrystalline structure of PVA was retained without the formation of a new crystalline phase, while the crystallinity index increased from 71.79% to 87.91%. The combined incorporation of CNF and MLE therefore produced strong, tough, and UV-shielding PVA films with potential application as light-protective packaging materials.