Article Per Year (5 Year)
p-Index From 2020 - 2025
0
P-Index
This Author published in this journals
All Journal Dinamika Teknik Mesin : Jurnal Keilmuan dan Terapan Teknik Mesin
Wardani, K.
Unknown Affiliation
Aerospace Engineering Automotive Engineering Mechanical Engineering Physics

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

 1 
Variasi sudut pemasangan tabung kompresor terhadap unjuk kerja pompa hidram Sutanto, R.; Wardani, K.; Alit, I.B.; Wirawan, M.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 8, No 2 (2018): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (388.161 KB) | DOI: 10.29303/dtm.v8i2.234

Abstract

Water is one of the factors which very important and necessary in the life of living creatures. Therefore,  water  must  be  available  whenever  and  wherever  in  the  quantity,  timing,  and sufficient quality. Hydraulic Ram Pump (Hydram) is a pump which does not require external energy as the power source. The purposes of this research are understanding the influence of mounting tube compressor with tilt angle from the water weight-lift of output pipe .This  research  uses  hydrant  pump  by  the  specification of  tube  compressor where  its’ diameter 3 inches and a height of 60 cm. The falling angle of pump is 35°. The falling-height is 2 meter with 4 variations of weight-lift 4, 4½, and 5 meters.The method of analysis is conducted by analyzing data obtained during the experiment, where the   results in the form of quantitative data which is presented in type of   tables and displayed in graphical form. The results of the research shows that  the best output debit on mounting tube compressor variation 90° that is 0.035 l/s  with 4 meters water weight-lift, while the lowest output debit on mounting tube compressor variation that is 0.011 l/s 5 meters water weight-lift. The best efficiency is 27.3 % in the mounting tube compressor variation 90°  with 4 meters of water weight-lift, while the lowest efficiency is 6.5 % in the mounting tube compressor variation 90° with 5 meters of water weight-lift.
Analisa unjuk kerja alat pembagi tekan pada pompa hydram Wardani, K.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 9, No 2 (2019): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (69.647 KB) | DOI: 10.29303/dtm.v9i2.287

Abstract

Water is source of life for human being, plant and animal. One of  effort to complete of water required is by using hydram pump. Hydram pump (Hydraulic ram pump) is a pump that work without required energy from outside for its activated, but work done by exploiting force from source of water. This research purposes to know influence of pressure divisor to water hammer effect and to know influence of pressure divisor to efficiency of hydram pump. This research used hydram pump by the specification of air tube it’s 60 cm height and 3 inches diameter. Elevation of plunge from pump body is 2 meters and elevation of output is 4 meters. Height of air tube at pressure divisor that is 20 cm, 30 cm, 40 cm and 50 cm and elevation of variaty pressure divisor from body pump is 2 meters, 2,5 meters and 3 meters. The method used in this research is experiment method. The quantitative data  made in table and displayed graphically. The results show that the highest of maximum head at 2 meters elevation of pressure divisor  from pump body and 20 cm high of tube, while lowest of maximum head at 3 meters elevation of pressure divisor  from pump body and 50 cm high of tube. The best efficiency at 2 meters elevation of pressure divisor  from pump body and 20 cm high of tube that is 31,62%, while the lowest efficiency at hydram pump installation without of pressure divisor that is only 26,62%.
Variasi sudut pemasangan tabung kompresor terhadap unjuk kerja pompa hidram Sutanto, R.; Wardani, K.; Alit, I.B.; Wirawan, M.
Dinamika Teknik Mesin Vol 8, No 2 (2018): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29303/dtm.v8i2.234

Abstract

Water is one of the factors which very important and necessary in the life of living creatures. Therefore,  water  must  be  available  whenever  and  wherever  in  the  quantity,  timing,  and sufficient quality. Hydraulic Ram Pump (Hydram) is a pump which does not require external energy as the power source. The purposes of this research are understanding the influence of mounting tube compressor with tilt angle from the water weight-lift of output pipe .This  research  uses  hydrant  pump  by  the  specification of  tube  compressor where  its’ diameter 3 inches and a height of 60 cm. The falling angle of pump is 35°. The falling-height is 2 meter with 4 variations of weight-lift 4, 4½, and 5 meters.The method of analysis is conducted by analyzing data obtained during the experiment, where the   results in the form of quantitative data which is presented in type of   tables and displayed in graphical form. The results of the research shows that  the best output debit on mounting tube compressor variation 90° that is 0.035 l/s  with 4 meters water weight-lift, while the lowest output debit on mounting tube compressor variation that is 0.011 l/s 5 meters water weight-lift. The best efficiency is 27.3 % in the mounting tube compressor variation 90°  with 4 meters of water weight-lift, while the lowest efficiency is 6.5 % in the mounting tube compressor variation 90° with 5 meters of water weight-lift.
Analisa unjuk kerja alat pembagi tekan pada pompa hydram Wardani, K.
Dinamika Teknik Mesin Vol 9, No 2 (2019): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29303/dtm.v9i2.287

Abstract

Water is source of life for human being, plant and animal. One of  effort to complete of water required is by using hydram pump. Hydram pump (Hydraulic ram pump) is a pump that work without required energy from outside for its activated, but work done by exploiting force from source of water. This research purposes to know influence of pressure divisor to water hammer effect and to know influence of pressure divisor to efficiency of hydram pump. This research used hydram pump by the specification of air tube it’s 60 cm height and 3 inches diameter. Elevation of plunge from pump body is 2 meters and elevation of output is 4 meters. Height of air tube at pressure divisor that is 20 cm, 30 cm, 40 cm and 50 cm and elevation of variaty pressure divisor from body pump is 2 meters, 2,5 meters and 3 meters. The method used in this research is experiment method. The quantitative data  made in table and displayed graphically. The results show that the highest of maximum head at 2 meters elevation of pressure divisor  from pump body and 20 cm high of tube, while lowest of maximum head at 3 meters elevation of pressure divisor  from pump body and 50 cm high of tube. The best efficiency at 2 meters elevation of pressure divisor  from pump body and 20 cm high of tube that is 31,62%, while the lowest efficiency at hydram pump installation without of pressure divisor that is only 26,62%.
Co-Authors I.B. Alit, I.B. M. Wirawan, M. Sutanto, R.