Article Per Year (5 Year)
p-Index From 2020 - 2025
0.408
P-Index
This Author published in this journals
All Journal Dinamika Teknik Mesin : Jurnal Keilmuan dan Terapan Teknik Mesin
Mara, M.
Unknown Affiliation
Aerospace Engineering Automotive Engineering Mechanical Engineering Physics

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Uji sifat fisik dan kimia bioetanol dari jagung (Zea mays L) Tira, H.S.; Mara, M.; Zulfitri, Z.; Mirmanto, M.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 8, No 2 (2018): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (137.264 KB) | DOI: 10.29303/dtm.v8i2.231

Abstract

The aim of this research is to know the physical characteristics and chemical contents of corn bioethanol (Zea Mays L.). The bioethanol is produced by distillation process through variations in fermentation duration. The bioethanol produced then was tested in order to measure the physical characteristics and sulphur content. The measured physical and chemical characteristics of bioethanol were density, kinematic viscosity, flash and fire point and sulphur content.The results showed that the physical characteristic value and sulphur content of the bioethanol had close values compared to those of the standart. They were found in fermentation with duration of 70 hours under second distillation process. However a further research is still be required to obtain a suitable characteristic for transpostation purpose. 
Pengaruh variasi ketebalan saluran dan temperatur tuang terhadap fluiditas dan porositas hasil pengecoran kuningan pada pengecoran evaporatif Sugita, I.K.; Mara, M.; Priambadi, I.G.N.; Nuarsa, I.M.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 13, No 1 (2023): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29303/dtm.v13i1.627

Abstract

The development of foundry technology continues to grow along with the increasingly complex needs for making products based on art and culture, one of which is sclupture. Evaporative casting based on non-permanent patterns made of polystyrene foam, with the advantage of precision casting results in complex shapes. The purpose of this study was to determine how variations in the pouring channel and pouring temperature affect the fluidity and porosity of brass castings in evaporative casting. Casting was carried out in castings with thicknesses of 1.5, 2, 3, 4, and 5 mm at pouring temperatures of 900°C, 950°C, and 1000°C using brass with a composition of Cu60% and Zn40%. The highest fluidity was found at a pattern density of 0.012 gr/cm3 at a pouring temperature of 1000°C with a flow length of 150 mm, while the lowest fluidity was obtained at a pattern density of 0.016 gr/cm3 at a pouring temperature of 900°C with a flow length of 13 mm. The results of scanning electron microscope (SEM) observations can be observed in spesimens with a density of polystyrene foam and a high casting temperature, an increase in the porosity formed.
Uji performansi motor listrik sebagai penggerak kendaraan listrik Mara, M.; Yudhyadi, I.G.N.K.; Adhi, I.G.A.K.C.; Setyawan, P.D.; Triadi, A.A.A.
Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin Vol 13, No 1 (2023): Dinamika Teknik Mesin: Jurnal Keilmuan dan Terapan Teknik Mesin
Publisher : Universitas Mataram

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29303/dtm.v13i1.607

Abstract

Co-Authors A.A.A. Triadi, A.A.A. Adhi, I.G.A.K.C. M. Mirmanto, M. Nuarsa, I.M. P.D. Setyawan, P.D. Priambadi, I.G.N. Sugita, I.K. Tira, H.S. Yudhyadi, I.G.N.K. Zulfitri, Z.